DataMuseum.dk

top - download

    Length: 4002 (0xfa2)
    Types: TextFile
    Names: »RELDESCR.T«

└─⟦e0c43619c⟧ Bits:30005797 CR80 Disc pack ( Vol:FNJ1 861029/EC CR80 S/W Package II+III+IV+V+VII )
    └─ ⟦this⟧ »CSP003_V0701.D!CSS182.D!RELDESCR.T« 

TextFile

*******************************************************

         R E L E A S E   D E S C R I P T I O N

*******************************************************




Module id number: CSS/182
--------------------------

Module name:      MAG-TAPE BACKUP
-----------------------------------

Actual release:   04.02            Release date: 860527
-----------------------            --------------------

Previous release: 04.01            Release date: 860408
-----------------------            --------------------




New facilities:
---------------

   >> V0402 <<

   None.

   >> V0401 <<

   -  Two new parameters added: R and D specifying the tape controller
      RAM address and device address. These parameters overrun the
      contents of the MT_CONFIG.T file.
   -  The program now exists in two versions: the usual version that
      requires support from TOS, and a new version supplied as a
      boot module, that reads its parameters interactively from
      the main console.

   >> V0301 <<

   -  The program is capable of restarting a backUP at a
      specified tapenumber.
   -  The program can use 2 tapestations alternating.
   -  The new, extended alternative sector file is supported.

   >> V0202 <<

   -  The configuration parameters are fetched from a disk file.
      This solution is more flexible and makes it possible to
      support all kinds of MX-AMOS installations.
      The name of the disk file is

      MT_CONFIG.T

      and it must reside in the same directory as MT_BACKUP

      This file must be edited to contain two lines :

      D:<device addr> <NL>
      R:<RAM    addr> <NL>

      where <device addr> is an integer with three compartments
      bit 12-15 : crate no (AMOS & XAMOS : 0)
      bit  6-11 : 0
      bit  0- 5 : device address (AMOS & XAMOS : #1F)

      and <RAM addr> is an integer stating the start address of the
      magtape controller RAM in units of one K relative to start of
      crate (AMOS & XAMOS : 240(page3 version) or 172(page2 version))
      A file with (X)AMOS defaults is deliverable.

Changes:
--------

   >> V0402 <<

   -  The buffer for alternative sector file is now only allocated
      at backDOWN and only as large as required by the volume
      stored on the tape.
   -  DAMOS version now deleted completely.

   >> V0401 <<

   -  The tape controller RAM now contains the main buffers.
   -  The buffer for alternative sectors is now externally allocated.

   >> V0301 <<

   -  The program will start using a tape automatically if it is
      ready for use. If not, it will wait for an answer from the
      operator stating that the tape is ready.

   >> V0202 <<

   -  Copy to/from MT controller RAM is done via the transfer monitor
      procedures introduced to ease upgrading of programs to MX-AMOS.
      Performance is slightly reduced when running AMOS but improved
      for XAMOS.
      This means that one and the same version may run under all three
      AMOS based systems.

Errors corrected:
-----------------

   >> V0402 <<

   -  Sectors are now only tried substituted when relevant
      completion codes are received from the disk I/O
      operations.
   -  ':'s and '.'s are now allowed as separators when reading
      the time to be set in the bootversion.
   -  Linked with version 0204 of MTC module.

   >> V0401 <<

   -  This and all earlier versions requires ECO #2136 done on the
      CR8045M Dual bus tape ctrl.

   >> V0302 <<

   -  The program is linked with MTC version 2.3 with better handling
      of interrupts.

Reported errors, not corrected:
-------------------------------

CPECRs implemented in current release:
--------------------------------------

  PR 86363

Comments:
---------

               !!!!!!   W A R N I N G   !!!!!!

   The operator must be very careful to inspect, that no other
   tapes are mounted on the tapestation(s) than the ones, that
   shall be used for the backup, as the program now may start an
   automatic copy onto them.