top - download
⟦0e5ebf81d⟧ Wang Wps File
Length: 3066 (0xbfa)
Types: Wang Wps File
Notes: Spelunked
Names: »~ORPHAN73.00«
Derivation
└─⟦1347aae84⟧ Bits:30006174 8" Wang WCS floppy, CR 0315A
└─ ⟦this⟧ »~ORPHAN73.00«
WangText
H…09…H…0e…H
H…06…H…07…G…0c…G…02…G…07…F…0d…F…00…F
C…08…C…0c…C…00…C…05…B…0a…B…0f…B A…09…A…0e…A
@…08…@…0d…@…02…@…07…?…0d…?…02…?…86…1
…02…
…02… …02…
…02…CPS/TPR/038
…02…OJG/830516…02……02…
FACTORY
ACCEPTANCE
TEST SPECIFICATION
AND PROCEDURES,
SITE 12…02……02…CAMPS
3.2.3.2.4 T̲e̲s̲t̲ ̲T̲e̲r̲m̲i̲n̲a̲t̲i̲o̲n̲
Power Down the system as Follows:
a) Depress "START" push button on Disk Drive # 2 and
wait until he "START" and "READY" indicators are
"OFF".
b) Rmove the Disk Pack from Disk Drive # 2, close
the lid and push the drive back in rack B
c) The two scratch Floppy Disks are removed from the
Floppy Disk drive in rack C. Close the lids.
d) The Power Switch (2) on each Mains Switch is set
to "OF".
e) The input power switch on each Frequency Stabilizer
is set to "OFF"
f) Power Down all connected Terminals i.e. VDUs, MSPs,
OC, PTP/PTR, OCR as applicable.
g) Disconnect the OC from the leftmost V24/V28(L/L)
adaptor in the Adaptor crate f rack C, and replace
this adaptor with the originally mounted OPTO transceiver.
h) Disconnect the two V24 cables (at the WDP rear
crate), remove the short extension cable and reconnect
the two cables to J2 and J3 respectively.
i) Interchange te TIA#1 (PU#2 rear crate, slot 15)
TDX connection and the TIA#2 (PU#2 rear crate,
slot 16) TDX connection.
j) Set the host number on the STI (PU#2 front crate,
slot 18) to #02 on switch S1 as follows:
S1,4 : CLOSED
S1,3 : CLOSED
S1,2 : OPE
S1,1 : CLOSED
3.2.3.3 T̲e̲s̲t̲ ̲P̲r̲o̲c̲e̲d̲u̲r̲e̲ ̲3̲
This testprocedure serves to verify the Watchdog Processor
System i.e. the Watchdog Processor Unit (WDP), the
Configuration Control Bus Adapter (CCBA, the Channel
Unit Control Panel (CUCP), the TDX Bus Switching Modules
(BSM-Xs) and the Configuration Control Adapters (CCAs).
3.2.3.3.1 T̲e̲s̲t̲ ̲S̲e̲t̲ ̲U̲p̲
The test is performed via an Operator Console (OC)
which is a printer and keyboard, a TEST VDU1 and a
TEST VDU#2 all with V24/V28 interface and a Medium
Speed Printer (MSP) with OPTO interface.
The above mentioned testequipment is connected to the
system as follows:
1.Substitute the leftmost OPTO transceiver in the
rack C Adapter crate with a V24/V28(L/L) adapter
(1 channel), and connect the OC to the V24 connector
on the front panel of the adaptor.
2. Connect the MSP to the remaining OPTO transceiver
in the dapter crate in rack C.
3. Connect TEST VDU#1 to J26 in the V24 FILTER
BOX.
4. Connect TEST VDU#2 to J27 in the V24 FILTER
BOX.
5. Disconnect the two V24 cables connected to
the J1 and J2 connectors on the leftmost Back
Panel 8 located in the rear of he Adapter crate.
6. Disconnect the V24 cable connected to the MIA
in PU#1 and connect TESTCABLE#1 between above
mentioned (para. 5) J1 and the MIA.
7. Disconnect the V24 cable connected to the MIA
in PU#2 and connect TESTCABLE#2 between abov
