top - download
⟦12ad3761a⟧ Wang Wps File
Length: 13585 (0x3511)
Types: Wang Wps File
Notes: Spelunked
Names: »~ORPHAN69.00«
Derivation
└─⟦3fbecbc6f⟧ Bits:30006206 8" Wang WCS floppy, CR 0307A
└─ ⟦this⟧ »~ORPHAN69.00«
WangText
c…00……00……00……00…E…02……00……00…E
D…0a…D…0b…D…00…D
D…07…C…0a…C…0f…C C…06…B…0b…B…0d…B…01…B
B…07…A…09…A…0e…&…02…&…06…%…0b…%…0f…%
$…08…$…0c…$…01…$…05…#…0a…#…0e…#
#…07…"…08…"…0a…"…0f…" "…07…!…0a…!…0d…!…02…!…06… …08… …0c… …0f… …1f……86…1 …02… …02… …02…
2767A/ktd …02… CPS/TCM/005
…02……0f…KJA/830714…02……02…
CAMPS SITE LEVEL MAINTENANCE MANUAL
…02……02… CAMPS…0e…
4.7 O̲F̲F̲ ̲L̲I̲N̲E̲ ̲M̲&̲D̲ ̲T̲E̲S̲T̲ ̲P̲R̲O̲G̲R̲A̲M̲S̲
4.7.1 I̲n̲t̲r̲o̲d̲u̲c̲t̲i̲o̲n̲
Section 4.7.1 describes the
- Purpose
- Characteristic
- Operation
of the offline M&D test programs.
a) P̲u̲r̲p̲o̲s̲e̲
Te purpose of the offline test programs is to help
the maintenance personnel pinpoint a hardware malfunction
to a module/unit and to verify that a tested module/unit
is able to function properly.
b) C̲h̲a̲r̲a̲c̲t̲e̲r̲i̲s̲t̲i̲c̲
The test programs are characteized as o̲f̲f̲l̲i̲n̲e̲ test
programs. This means that the activated test programs
requires total control of a Processor Unit (PU),
i.e. it is necessary to take the standby PU offline
before operating the offline test programs.
c) O̲p̲e̲r̲a̲t̲i̲o̲n̲
The offlin test programs are stored on a storage
medium (SMD disk pack or floppies). It is, therefore,
necessary to boot the actual test program into
the (offline) Processor Unit (PU) before activating
it.
The boot and activation commands are entered on
te maintenance position VDU. Table 4.7.1-1 shows
schematically the operation of the offline test
programs.
When the program is booted, it outputs: "-- " and
is ready to accept and execute commands.
When a test is stated, then the program takesfull
control of the off-line PU and does not accept
commands from the maintenance position VDU before
it has finished the test.
It is, however, possible to stop the test by pressing
the "ATTN" key on the Maintenance Position VDU
keyboard or by pessing the MC button on the MAP
module situated in the Offline PU crate.
Figure 4.7.1-1
4.7.2 U̲s̲e̲r̲ ̲I̲n̲t̲e̲r̲f̲a̲c̲e̲
Section 4.7.2 describes for each of the offline M&D
Test Programs:
- The boot and activation command (section 4.7.2.1).
- The expected output from the Tes Programs (section
4.7.2.2).
Certain general rules were described in the "MAINTENANCE
POSITION OPERATION MANUAL" for command entry, editing
and validation. In the following the more specific
rules concerning:
- Data Entry
- Validation
- Dat Exit Conditions
are presented.
a) D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
It is possible to boot the offline M&D test program
when the DAMOS BootLoader is activated. (This can
be done by pressing the "MC" button on the front
of the MAP Module in the actual PU Crate.
After the test program is booted, the activation
command is entered.
This is done by entering the test command or
Do body
This commandtype is used to activate a testsequence
resident in main memory, i.e. the actual test program
nowaccepts testcommands from this testsequence
and not from the maintenance position.
When the activated testsequence has finished, command
inputs are again taken from the maintenance position.
b) V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
Full validation is performed only after data entry
is complete and ENTERED.
If the entered command is valid the program will
execute the specified commandfle.
If an invoiced command is entered the system will
inform you by providing an errorcode on the VDU
screen.
c) E̲x̲i̲t̲ ̲C̲o̲n̲d̲i̲t̲i̲o̲n̲s̲
If an exit of a test command is wanted then it
is accomplished by pressing the "ATTN" key and
a new command cn be entered.
This command activates the DAMOS bootLoader and
a masterclear is issued.
4.7.2.1 I̲n̲p̲u̲t̲
This section describes the activation procedures of
the Offline M&D Test Programs.
The section is divided in the following sections:
S̲e̲c̲t̲i̲o̲n̲ C̲o̲n̲t̲e̲n̲t̲s̲ N̲o̲t̲e̲
4.7.2.1.1 Initial Format A description of the
actions to be executed
before the bootcommand
can be executed.
4.7.2.1.2 CPU A description of the
activation commands
of the CPU Test.
4.7.2.1.3 MAP A description of the
activation commands
of the MAP Test.
4.7.2.1.4 RAM A description of the
activation commands
of the RAM Test.
4.7.2.1.5 DISK A description of the
activation commands
of the DISK Tests.
4.7.2.1.6 FD A descrition of the
activation commands
of the FD Tests.
4.7.2.1.7 LTU A description of the
activation commands
of the LTU Tests.
4.7.2.1.8 TDX A description of the
activation commands
of the TDX Tests.
4.7.2.1.1 INITIAL FORMAT
NO COMMAND
1 Switch "ON" the VDU Go to step 2.
2 Turn the keylock to the
"ON" position. Go to step 3.
3 Pressthe MC button on The following output
the front of the MAP appears on the screen:
Module situated in the
actual PU. 07 MAP/BIT: OK
DAMOS BOOT LOADER
VERSION..
CPU [
Go to step 4.
4 It is now possible to The disk boot commands
are
boot the test programs described in step
5-6.
from either a disk or
a floppy disk. The floppy disk
boot commands are
described in step
7-8.
4.7.2.1.1 INITIAL FORMAT (cont'd)
5 D̲i̲s̲k̲ ̲B̲o̲o̲t̲ ̲C̲o̲m̲m̲a̲n̲d̲s̲: - If the correct
disk is
mounted on the disk
drive.
Before booting the actual
test program, it is Go to stp 6.
necessary to verify that the
correct disk pack is situa- - If the mounted
disk is not
ted in the SMD disk drive the correct, then
it is
in Rack B. necessary to replace
the
The identity name of the disk pack.
disk pack in the SMD disk
must
be:
MD.TEST
When it is replaced,
go to step 6.
6 D̲I̲S̲K̲ ̲B̲o̲o̲t̲ ̲C̲o̲m̲m̲a̲n̲d̲s̲:̲ The elapsed time
of the boot
command is app 30
sec. The valid (bfd)
options
Type in the following and the sections
commands: describing the tsts
are
listed below:
BA 1[25 (CR)
BM 14[ (CR)
BE (BFD) (CR) T̲e̲s̲t̲ ̲ ̲ ̲(̲B̲F̲D̲)̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲S̲e̲c̲t̲i̲o̲n̲
CPU 4
4.7.2.1.2
MAP 5
4.7.2.1.3
RAM 6
4.7.2.1.4
DISK 7
4.7.2.1.5
FD 8
4.7.2.1.6
LTU 9
4.7.2.1.7
TDX A
4.7.2.1.8
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲…86…1 …02…
…02…
…02… …02… …02…
4.7.2.1.1 INITIAL FORMAT (cont'd)
7 F̲l̲o̲p̲p̲y̲ ̲D̲i̲s̲k̲ ̲B̲o̲o̲t̲ ̲C̲o̲m̲m̲a̲n̲d̲s̲:̲
- If the correct
floppy is
Before booting the actual mounted.
test program it is necessary Go to ste 8.
to verify that the correct
floppy disk is situated - If it is not the
correct
in the floppy disk in Rack floppy, it is necessary
to
B. replace the floppy
with the
There is a floppy for each correct floppy (refer
to
M&D offline test section 4.4).
The following options are When it is replaced,
given: Go to step 8
T̲E̲S̲T̲ ̲ ̲F̲l̲o̲p̲p̲y̲ ̲N̲a̲m̲e̲
CPU CPU ̲Test
MAP MAP ̲Test
RAM RAM ̲Test
TDX TDX ̲Test
LTU LTU ̲Test
FD FD ̲Test
DISK DISK ̲Test
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
8 F̲D̲ ̲B̲o̲o̲t̲ ̲C̲o̲m̲m̲a̲n̲d̲s̲: (The elapsed time
of the boot command
is app 30 sec)
Type in the following The BU command specifies
commands: the identification
of the
drive from which
the
BA 1[[1 (CR) program is booted.
BT FD5[ (CR) BU 1 specifies FD
drive No 1
BU [ or BU 1 (CR) BU [ specifies FD
drive No [
BE (CR) No [ is default
value
4.7.2.1.1 INITIAL FORMAT (cont'd)
The sections
describing the tests
are
listed below:
T̲E̲S̲T̲ ̲ ̲S̲e̲c̲t̲i̲o̲n̲ ̲ ̲
̲ ̲ ̲ ̲ ̲
CPU 4.7.2.1.2
MAP 47.2.1.3
RAM 4.7.2.1.4
DISK 4.7.2.1.5
FD 4.7.2.1.6
LTU 4.7.2.1.7
TDX 4.7.2.1.8
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲
4.7.2.1.2 CPU TEST
CPU TEST: The CPU test boot
command are as follows:
- D̲i̲s̲k̲ ̲b̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[25 (CR)
BM 14[ (CR)
̲B̲E̲ ̲ ̲4̲ ̲ ̲ ̲(̲C̲R̲)̲
̲ ̲ ̲ ̲ ̲
- F̲D̲ ̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[[1 (CR)
BT FD5[[ (CR)
BU [ or 1 (CR)
̲B̲E̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲(̲C̲R̲)̲
̲ ̲
When the test program
is booted the following
output appears on
the VDU:
CSS/718 TEST CPU-CACHE
VS...
CPU [ IN TEST:
----
1 Enter frm the maintenance
position:
REPORTLEVEL = [ (CR) Elapsed time of
test: 30 sec
ACTIVATE CPU [ (CR)
ACTIVATE CPU 1 (CR) N̲o̲t̲e̲:
ACTIVATE CPU 2 (CR)
TEST CPU [ 1 2 (CR) If the test time
exceeds the
specified elapsed
time plus
25% max 5 min),
or the test stopped
when testing one
of the CPU's, then
the test program
has detected an
unrecognizable error
and it is necessary
to break from the
test by pressing
the "ATTN" key on
the Maintenance
Position VDU keyboard
or by pressing he
MC button on the
front if the offline
PU MAP module.
4.7.2.1.2 CPU TEST (cont'd)
The expected result
is listed in section
4.7.2.2
Go to step 2.
2 QUIT the CPU Test by The "QUIT" command
activates
entering: the DAOS Boot Loader
and
the following output
QUIT (CR) appears:
7 MAP BIT OK:
DAMOS BOOT LOADER
VERSION...
CPU [
It is now possible
to boot other test
programs (refer
to section 4.7.2.1.1)
4.7.2.1.3 MAP TEST
MAP TEST: The MAP test boot
commands are as
follows:
- D̲i̲s̲k̲ ̲b̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[25 (CR)
BM 14[ (CR)
̲B̲E̲ ̲ ̲5̲ ̲ ̲(̲C̲R̲)̲ ̲
̲ ̲ ̲ ̲ ̲
- F̲D̲b̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1001 (CR)
BT FD 5[[ (CR)
BU [ or 1 (CR)
̲B̲E̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲(̲C̲R̲)̲
When the test program
is booted, the following
output appears on
the VDU:
CSS/721 CR80M MAP
TEST VS.103
CPU [
-----
1 Enter from te maintenance
position:
REPORTLEVEL = 2 (CR) Elapsed time of
test: app
TEST ALL (CR) 15 min
N̲o̲t̲e̲:
If the test time
exceeds the
specified elapsed
time plus
25%, then the test
program has detected
an unrecognizable
error andit is necessary
to break from the
test by pressing
the "ATTN" key on
the Maintenance
Position VDU keyboard.
4.7.2.1.3 MAP TEST (cont'd)
The expected result
is listed in section
4.7.2.2.
Go to step 2.
2 QUIT the MAP test by THE "QUIT" command
activates
entering: the DAOS Boot Loader
and
the following output
QUIT (CR) appears:
07 MAP BIT OK:
DAMOS BOOT LOADER
VERSION...
CPU [
It is now possible
to boot other programs
(refer to section
4.7.2.1.1.)
4.7.2.1.4 RAM TEST
RAM TEST: The RAM test boot
commands are as
follows:
- D̲i̲s̲k̲ ̲b̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[25 (CR)
BM 14[ (CR)
̲B̲E̲ ̲6̲ ̲(̲C̲R̲)̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲
- F̲D̲ ̲b̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[[1 (CR)
BT FD5[[ (CR)
BU [ or 1 (CR)
̲B̲E̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲(̲C̲R̲)̲
̲
When the test program
is booted the following
output appears on
the VDU:
CSS/0709 CR80M MEMORY
TEST
VS. 100.
CPU [
----
1 Enter from th maintenance
position:
REPORTLEVEL = 2 (CR) Elapsed time of
test: 15
TEST ALL (CR) min.
N̲o̲t̲e̲:
If the test time
exceeds the specified
elapsed time plus
25%, then the test
program has detected
an unrecognizable
error and it is
necesary to break
from the test by
pressing the "ATTN"
key on the Maintenance
Position VDU keyboard.
4.7.2.1.4 RAM TEST (cont'd)
The expected result
is
listed in section
4.7.2.2.
Go to step 2.
2 QUIT the RAM test by The "QUIT" command
activates
entering: theDAMOS Boot Loader
and
the following output
QUIT (CR)appears:
07 MAP BIT OK:
DAMOS BOOT LOADER
VERSION...
CPU O.
It is now possible
to boot other test
programs.
(refer to section
4.7.2.1.1.)
4.7.2.1.5 DISK TEST
DISK/DCA/DISK DRIVE TEST: NOTE: The DISK test
boot commands are
as follows:
- D̲i̲s̲k̲ ̲b̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[25 (CR)
BM 14[ (CR)
̲B̲E̲ ̲7̲ ̲C̲R̲)̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲
- F̲D̲ ̲b̲o̲o̲t̲ ̲c̲o̲m̲m̲a̲n̲d̲s̲:
BA 1[[1 (CR)
BT FD5[[ (CR)
BU [ or 1 (CR)
̲B̲E̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲(̲C̲R̲)̲
When the test program
is booted the following
output appears on
the VDU:
CSS/730 CR80M DISK
FD TEST
VS.101.
CPU [.
----
1 There are three different
offline M&D disk test N̲O̲T̲E̲
programs.
Verify that a disk
pack is
The steps describing them mounted in the drive
(if it
are listed below: is a SMD)
T̲E̲S̲T̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲S̲T̲E̲P̲ When the test isselected
it
DISK 2 is necessary to
identify the
DISK-RW 6 actual DISK CONTROLLER/DCA/
D̲I̲S̲K̲-̲F̲O̲R̲M̲A̲T̲ ̲ ̲ ̲1̲1̲ ̲ DISK DRIVE.
The identification
numbers
(no's) are as follows:
no DISK
DISK
CTRL
DRIVE
̲ ̲ ̲ ̲ ̲ ̲ ̲s̲l̲o̲t̲ ̲N̲o̲ ̲ ̲ ̲i̲n̲ ̲r̲a̲c̲k̲
1 20
A
2 18
B
̲ ̲3̲ ̲ ̲ ̲ ̲ ̲ ̲1̲6̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲C̲ ̲ ̲ ̲…86…1 …02… …02…
…02… …02…
…02…
4.7.2.1.5 DISK TEST (cont'd)
2 DISK TEST: NOTE: The "DISK"
Test contains an
offline test of
the Disk System.
This test does not
destroy the data
stored on the disk.
Go to step 3.
It is possible to
activate a Disk
Test to each of
the three DISK CONTROLLER/DCAs/
DISK DRIVE's.
3 Enter from the maintenance The valid no's are:
position: 1, 2, 3.
DO DISKno (CR) Elapsed time of
test: app. 30 sec.
N̲
