top - download
⟦55478fd42⟧ Wang Wps File
Length: 58100 (0xe2f4)
Types: Wang Wps File
Notes: Spelunked
Names: »~ORPHAN66.02«
Derivation
└─⟦48a409da8⟧ Bits:30006053 8" Wang WCS floppy, CR 0082A
└─ ⟦this⟧ »~ORPHAN66.02«
WangText
…02…CPS/230/ICD/0002
…02…820719 …02……02…
SUPERVISOR COMMANDS AND PROCEDURES
…02…Issue 4.1…02…CAMPS
5.2.5 C̲o̲n̲t̲i̲n̲u̲e̲ ̲A̲b̲b̲r̲e̲v̲i̲a̲t̲e̲d̲ ̲P̲l̲a̲i̲n̲d̲r̲e̲s̲s̲ ̲P̲r̲e̲p̲a̲r̲a̲t̲i̲o̲n̲ ̲(̲C̲A̲P̲P̲)̲
This function is similar to Continue Plaindress Preparation
and is described in section 5.2.4.
5.2.6 C̲o̲n̲t̲i̲n̲u̲e̲ ̲A̲b̲b̲r̲e̲v̲i̲a̲e̲d̲ ̲S̲e̲r̲v̲i̲c̲e̲ ̲M̲e̲s̲s̲a̲g̲e̲ ̲P̲r̲e̲p̲a̲r̲a̲t̲i̲o̲n̲ ̲(̲C̲A̲S̲P̲)̲
This function is similar to the Continue Plaindress
Preparation as described in section 5.2.4.…86…1
…02… …02… …02… …02…
Fig. 5.2.7-1…86…1 …02… …02… …02… …02…
5.2.7 S̲e̲r̲v̲i̲c̲e̲ ̲M̲e̲s̲s̲a̲g̲e̲ ̲D̲e̲l̲e̲t̲i̲o̲n̲ ̲(̲D̲E̲S̲M̲)̲
This Format (Fig. 5.2.7-2) is available for the supervisor
from the service message menu.
5.2.7.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
The supervisor shall enterthe Item Reference identity
of the message. Only deferred messages can be deleted.
5.2.7.2 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
If the reference is to a non-existing message, then
an error is given in the response line. If the reference
is to a message which has alredy been sent, then an
error is given in the response line.…86…1 …02… …02…
…02… …02…
Fig. 5.2.7-2…86…1 …02… …02… …02… …02…
Fig. 5.2.8-1…86…1 …02… …02… …02… …02…
5.2.8 S̲t̲a̲t̲u̲s̲ ̲o̲f̲ ̲O̲u̲t̲g̲o̲i̲n̲g̲ ̲S̲e̲r̲v̲i̲c̲e̲ ̲M̲e̲s̲s̲a̲g̲e̲s̲ ̲(̲O̲S̲M̲S̲)̲
This format (Fig. 5.2.8-2) is available for the supervisor
via the Service Message Menu.
The format is created by the system toinform the supervisor
of the status of service messages prepared at this
terminal since 24.00 hours.
5.2.8.1 D̲a̲t̲a̲ ̲P̲r̲e̲s̲e̲n̲t̲a̲t̲i̲o̲n̲
5.2.8.1.1 M̲e̲s̲s̲a̲g̲e̲s̲ ̲S̲e̲n̲t̲ ̲f̲o̲r̲ ̲T̲r̲a̲n̲s̲m̲i̲s̲s̲i̲o̲n̲
The system gives a list of service messages sent for
transmission showin the Time Stamp and Item Reference
identity.
5.2.8.1.2 D̲e̲f̲e̲r̲r̲e̲d̲ ̲M̲e̲s̲s̲a̲g̲e̲s̲
The system gives a list of service messages deferred,
showing the Time Stamp and Item Reference identity.
5.2.8.1.3 M̲e̲s̲s̲a̲g̲e̲s̲ ̲D̲e̲l̲e̲t̲e̲d̲ ̲S̲i̲n̲c̲e̲ ̲P̲r̲e̲v̲i̲o̲u̲s̲ ̲S̲t̲a̲t̲u̲s̲
The systemgives a list of Item Reference identity of
the messages deleted since previous status.
5.2.8.1.4 N̲u̲m̲b̲e̲r̲ ̲o̲f̲ ̲M̲e̲s̲s̲a̲g̲e̲s̲ ̲P̲r̲e̲p̲a̲r̲e̲d̲ ̲S̲i̲n̲c̲e̲ ̲P̲r̲e̲v̲i̲o̲u̲s̲ ̲S̲t̲a̲t̲u̲s̲
This gives the sum of the number of service messages
prepared since previous periodic status mesage.
5.2.8.2 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
No validation consequent to no data entry.…86…1
…02… …02… …02… …02…
Fig. 5.2.8-2…01…OUTGOING SERVICE MESSAGE STATUS…86…1 …02… …02… …02… …02…
Fig. 5.3.-1…01…RETRIEVAL FOR LOCA USE…86…1 …02… …02… …02… …02…
5.3 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲L̲O̲C̲A̲L̲ ̲U̲S̲E̲ ̲(̲R̲E̲L̲U̲)̲
This command displays the Retrieval keys and their
associated functions for Retrieval (see Fig. 5.3-2).
When the Supervisor Retrieves a messag by this command,
no further processing can be performed on it. The
supervisor can display the message on the VDU and make
a printed copy.
5.3.1 K̲e̲y̲ ̲T̲y̲p̲e̲ ̲E̲n̲t̲r̲y̲
The supervisor enters the code for the key type by
which the message is to be retreved.
In the following the Key Functions and Data Entries
are described.
Fig. 5.3-2…86…1 …02… …02… …02… …02…
5.3.2 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲A̲
This format (Fig. 5.3-3) can be used to retrieve incoming
(Format E1) or outgoing (Format E2) messages.
5.3.2.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.2.3.1.1 T̲i̲m̲e̲ ̲o̲f̲ ̲O̲c̲c̲u̲r̲r̲e̲n̲c̲ ̲(̲T̲O̲C̲)̲ ̲o̲r̲ ̲T̲O̲C̲ ̲W̲i̲n̲d̲o̲w̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
This is the TIME STAMP of the cataloguing of the message.
The cataloguing time for an incoming message is after
ACP127 analysis. For an outgoing message, the cataloguing
time is the time when transmission has ben finished.
5.3.2.1.2 C̲h̲a̲n̲n̲e̲l̲ ̲D̲e̲s̲i̲g̲n̲a̲t̲o̲r̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The Channel Designator identifies the channel of transmission
as of Format Line 1 of ACP127 formatted messages.
5.3.2.1.3 C̲h̲a̲n̲n̲e̲l̲ ̲S̲e̲r̲i̲a̲l̲ ̲N̲u̲m̲b̲e̲r̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The Channel serial number as f format line 1 of ACP127
formatted messages.…86…1 …02… …02… …02… …02…
Fig. 5.3-3…86…1 …02… …02… …02… …02…
5.3.3 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲B̲
This format (Fig. 5.3-4) can be used to retrieve incoming
(Format E1) or outgoing (Format E2) messages.
5.3.3.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.3.3.1.1 T̲i̲m̲e̲ ̲o̲f̲ ̲O̲c̲c̲u̲r̲r̲e̲n̲c̲ ̲(̲T̲O̲C̲)̲ ̲o̲r̲ ̲T̲O̲C̲ ̲W̲i̲n̲d̲o̲w̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
5.3.3.1.2 S̲t̲a̲t̲i̲o̲n̲ ̲I̲D̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The Station ID of the sending station as of format
line 3 in ACP127 formatted messages.
5.3.3.1.3 S̲t̲a̲t̲i̲o̲n̲ ̲S̲e̲r̲i̲a̲l̲ ̲N̲u̲m̲b̲e̲r̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The station serial number as of format lie 3 in ACP127
formatted messages.
5.3.3.1.4 F̲i̲l̲e̲ ̲T̲i̲m̲e̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
Time of Filing refers to the Julian date as derived
from Format Line 3 of ACP127 formatted messages.…86…1
…02… …02… …02… …02…
Fig. 5.3-4…86…1 …02… …02… …02… …02…
5.3.4 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲C̲
This format (Fig. 5.3-5) can be used to retrieve incoming
messages in Format E1, and outgoing messages in format
E2.
5.3.4.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.3.4.1.1 T̲i̲m̲e̲en finished.
5.3.2.1.2 C̲h̲a̲n̲n̲e̲l̲ ̲D̲e̲s̲i̲g̲n̲a̲t̲o̲r̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The Channel Designator identifies the channel of transmission
as of Format Line 1 of ACP127 formatted messages.
5.3.2.1.3 C̲h̲a̲n̲n̲e̲l̲ ̲S̲e̲r̲i̲a̲l̲ ̲N̲u̲m̲b̲e̲r̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The Channel serial number as f format line 1 of ACP127
formatted messages.…86…1 …02… …02… …02… …02…
Fig. 5.3-3…86…1 …02… …02… …02… …02…
5.3.3 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲B̲
This format (Fig. 5.3-4) can be used to retrieve incoming
(Format E1) or outgoing (Format E2) messages.
5.3.3.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.3.3.1.1 T̲i̲m̲e̲ ̲o̲f̲ ̲O̲c̲c̲u̲r̲r̲e̲n̲c̲ ̲(̲T̲O̲C̲)̲ ̲o̲r̲ ̲T̲O̲C̲ ̲W̲i̲n̲d̲o̲w̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
5.3.3.1.2 S̲t̲a̲t̲i̲o̲n̲ ̲I̲D̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The Station ID of the sending station as of format
line 3 in ACP127 formatted messages.
5.3.3.1.3 S̲t̲a̲t̲i̲o̲n̲ ̲S̲e̲r̲i̲a̲l̲ ̲N̲u̲m̲b̲e̲r̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The station serial number as of format lie 3 in ACP127
formatted messages.
5.3.3.1.4 F̲i̲l̲e̲ ̲T̲i̲m̲e̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
Time of Filing refers to the Julian date as derived
from Format Line 3 of ACP127 formatted messages.…86…1
…02… …02… …02… …02…
Fig. 5.3-4…86…1 …02… …02… …02… …02…
5.3.4 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲C̲
This format (Fig. 5.3-5) can be used to retrieve incoming
messages in Format E1, and outgoing messages in format
E2.
5.3.4.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.3.4.1.1 T̲i̲m̲e̲o̲f̲ ̲O̲c̲c̲u̲r̲r̲e̲n̲c̲e̲ ̲(̲T̲O̲C̲)̲ ̲o̲r̲ ̲T̲O̲C̲ ̲W̲i̲n̲d̲o̲w̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
This is the TIME STAMP of the cataloguing of the message.
The cataloguing of an incoming message in E…0f…1…0e… format
is performed after end distribution.
The cataloguing of an outgoing message in E…0f…2…0e… ormat
is performed after release.
5.3.4.1.2 D̲T̲G̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The DAY TIME GROUP refers to the time information that
exists as a part of format line 5 of ACP127 formatted
messages.
The DTG is assigned to a message during Release.
5.3.4.1.3 H̲a̲d̲q̲u̲a̲r̲t̲e̲r̲s̲ ̲I̲D̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
Originating Headquarters refer to the originating headquarters
PLA or PLA reference number as derived from format
line 6 of ACP127 formatted messages.
5.3.4.1.4 S̲I̲C̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
Subject Indicator code.…86…1 …02… …02… …02… …02…
Fig. 5.3-5…86…1 …02… …02… …02… …02…
5.3.5 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲D̲
This format 5.3-6 can be used to retrieve messages,
first draft of messages, Release Notifications and
comments.
5.3.5.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.3.5.1.1 T̲i̲m̲e̲ ̲o̲f̲ ̲c̲c̲u̲r̲r̲e̲n̲c̲e̲ ̲(̲T̲O̲C̲)̲ ̲o̲r̲ ̲T̲O̲C̲ ̲W̲i̲n̲d̲o̲w̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The cataloguing of first draft of a message is upon
completion of initial preparation. The cataloguing
of Release Notification is during release.
The cataloguing of a comment is after submission for
ditribution.
5.3.5.1.2 I̲t̲e̲m̲ ̲R̲e̲f̲e̲r̲e̲n̲c̲e̲ ̲I̲d̲e̲n̲t̲i̲t̲y̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The Item Ref. Id. is a 5 digits number. This number
will always be assigned to objects, by the system,
when the objects are stored.…86…1 …02… …02… …02… …02…
Fig. 5.3-6…86…1 …02… …02… …02… …02…
5.3.6 R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲K̲e̲y̲ ̲E̲
This format 5.3-7 can be used to retrieve incoming
message (E1).
5.3.6.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.3.6.1.1 D̲T̲G̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The DAY TIME GROUP refers to the time nformation that
exists as a part of format line 5 of ACP127 formatted
messages.
The DTG is assigned to a message during release.
5.3.6.1.2 H̲e̲a̲d̲q̲u̲a̲r̲t̲e̲r̲ ̲I̲D̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
Originating Headquarters refer to the originating headquarters
PLA or PLA reerence number as derived from format line
6 of ACP127 formatted messages.…86…1 …02… …02… …02… …02…
Fig. 5.3-7…86…1 …02… …02… …02… …02…
5.3.7 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
If the entered DTG means a search outside the currently
stored Data Base, then a system response message is
returned.
If the TOC window specified is too large,an error code
is returned.
If the retrieve key leads to a search outside the currently
stored Data Base, a system response message is returned
to assure the Supervisor that retrieval is in progress.
If more than one message satisfies the retrieal parameters,
a catalogue is displayed.
On retrieval completion, the catalogue display or the
retrieve message is delivered to the Supervisor, however
if retrieved message is from off-line storage, the
message is placed in the system response quue.
A catalogue display for key type A and B is shown in
Fig. 5.3-8 and for key type C, D, and E in Fig. 5.3-9.
If no message is found, a response message is displayed
in the system response line.
After presentation of a catalogue display or rsponse
message, the supervisor can enter new commands.…86…1
…02… …02… …02… …02…
Fig. 5.3-8…86…1 …02… …02… …02… …02…
Fig. 5.3-9…86…1 …02… …02… …02… …02…
Fig. 5.4-1…86…1 …02… …02… …02… …02…
5.4 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲R̲E̲A̲D̲D̲R̲E̲S̲S̲A̲L̲ ̲(̲R̲E̲A̲D̲)̲
This command displays a format (Fig. 5.4-2) with the
Retrieval Keys for Readdressal. Key types that can
be used under Readdressal are A, B, nd E and are similar
to these described under Retrieval For Local Use in
section 5.3.1, 5.3.2 and 5.3.5 respectively.
5.4.1 K̲e̲y̲ ̲T̲y̲p̲e̲ ̲E̲n̲t̲r̲y̲
The supervisor enters the code for the key type by
which message is retrieved for readdressal (A, B or
E
5.4.2 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲ ̲o̲f̲ ̲R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲D̲a̲t̲a̲
The requested Retrieval Key Format is displayed and
key data is inserted. After entry data is validated
in a similar way as described in section 5.3.8.
5.4.3 R̲e̲a̲d̲d̲r̲e̲s̲s̲a̲l̲
On retrieval, the message is diplayed and the Supervisor
can page through it with the PAGE ON and PAGE BACK
function keys. Readdressal can be continued by depressing
the ENTER-key. By depressing the CANCEL-key, the Readdressal
procedure is terminated.
On display of the forma in Fig. 5.4-4, the system inserts
Time Stamp and Originating Headquarters ID so the Readdressal
Assignment is referenced to the message.
On continuation of Readdresal, the format in Fig. 5.4-3
is displayed and data can be entered as follows.…86…1
…02… …02… …02… …02…
Fig. 5.4-2…86…1 …02… …02… …02… …02…
5.4.4 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
5.4.4.1 F̲r̲o̲m̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
The supervisor enters the name of one of the local
headquarters, using Plain Language Address (PLA), or
PLA reference number. Invali entry returns an error.
5.4.4.2 T̲o̲ ̲(̲M̲a̲n̲d̲a̲t̲o̲r̲y̲)̲
Either one action or one info addressee is mandatory.
5.4.4.3 T̲o̲ ̲A̲c̲t̲i̲o̲n̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The supervisor enters address(es) of the intended action
addressees. The supervisor should begin with Addrss
Indicator Groups (AIGs) if any. This should be followed
with PLAs or PLA reference numbers.
For invalid AIGs, the system will generate an error
after the validation process. If one of the entered
PLAs is not in the current PLA table, then anerror
is returned.
5.4.4.4 T̲o̲ ̲I̲n̲f̲o̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The same procedure is used as described for action.
5.4.4.5 E̲x̲e̲m̲p̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The supervisor enters the PLAs or PLA reference numbers
of the addresses to be excluded from any AIGs he has
used n the To lines. If invalid, then an error is
returned.
If the entry is not part of one of the AIGs in the
To lines, then an error is returned.
5.4.4.6 L̲o̲c̲a̲l̲ ̲P̲r̲i̲n̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)
The Supervisor may request a printed copy of the readdressal
Assignment.
5.4.5 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
When the supervisor depresses the ENTER key after copletion
of the Readdressal instruction, the system will validate
the entries as described above, and generate error
codes for invalid entries. The supervisor will have
to reenter data for invalid entries which is repeated
until all entries are vald.
5.4.6 T̲r̲a̲n̲s̲m̲i̲s̲s̲i̲o̲n̲
When all entries are valid, the message will be transmitted
and the supervisor will be presented with the current
menu. If any errors arise during the routing and transmission,
the message will be presented at the messag service
position.
F̲i̲g̲.̲ ̲5̲.̲4̲-̲3̲…86…1 …02… …02… …02… …02…
Fig. 5.4-4…86…1 …02… …02… …02… …02…
Fig. 5.5-1…86…1 …02… …02… …02… …02…
5.5 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲R̲E̲R̲U̲N̲ ̲(̲R̲E̲R̲N̲)̲
This command displays the associated format for Retrieval
key A, which is described in section 5.3.2, since this
is the only Key Type available forRerun. Only messages
transmitted earlier from this CAMPS site can be retrieved
for rerun. A transmission pilot will be automatically
generated.
5.5.1 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲ ̲O̲f̲ ̲R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲D̲a̲t̲a̲
Key data is entered and validated as described in section
5.3..
5.5.2 R̲e̲r̲u̲n̲
Retrieved message can be reviewed as described in section
5.4.3 and can be sent for Rerun by depressing the ENTER-key,
after which the current menu is displayed.
By depressing the CANCEL-key, the processing of the
message is teminated.…86…1 …02… …02… …02… …02…
Fig. 5.6-1…86…1 …02… …02… …02… …02…
5.6 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲R̲E̲D̲I̲S̲T̲R̲I̲B̲U̲T̲I̲O̲N̲ ̲(̲R̲E̲D̲S̲)̲
This command displays the associated format for Retrieval
Key C, described in section 5.3.4, since this is the
only key type available forredistribution. Only messages
earlier distributed at this CAMPS site can be retrieved
for redistribution.
The Time Stamp and Originating Headquarters ID is inserted
by the System so the assigned Redistribution can be
referenced to the message.
5.6.1 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲ ̲O̲f̲ ̲R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲D̲a̲t̲a̲
Key data is entered and validated as described in section
5.3.8.
5.6.2 R̲e̲d̲i̲s̲t̲r̲i̲b̲u̲t̲i̲o̲n̲
Retrieved message can be reviewed as described in section
5.4.3 and redistribution can be continued by depressing
the ETER-key.
By depressing the CANCEL-key, the Redistribution procedure
is terminated.
5.6.3 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
If the Redistribution shall continue, the format in
fig. 3.4.1 will be presented.
5.6.3.1 T̲o̲ ̲S̲C̲D̲s̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The action and Info SCDs frm the nominal distribution
list contained in the message will be presented in
the unprotected fields.
The supervisor will be able to delete SCD from the
nominal distribution and to specify new SCD to which
the retrieved message shall be distributed. However,
this redistribution wll not change the nominal distribution
list. Either one action or one info SCD is mandatory.
5.6.3.2 L̲o̲c̲a̲l̲ ̲P̲r̲i̲n̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The supervisor may specify a printed copy of the redistribution
instruction.
5.6.4 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
On entry of the Redstribution instruction, the system
will validate the SCD(s) and return an error for invalid
SCDs. The supervisor will have to reenter data for
invalid entries. The validation process will be repeated
until all entries are valid.
5.6.5 D̲i̲s̲t̲r̲i̲b̲u̲i̲o̲n̲
When all entries are valid, the message will be distributed
and the supervisor will be presented with the current
menu. If any errors arise during the distribution,
the message will be presented at the Message Distribution
control position.…86…1 …02… …02… …02… …02…
Fig. 5.6-2…86…1 …02… …02… …02… …02…
Fig 5.7-1…86…1 …02… …02… …02… …02…
5.7 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲D̲E̲L̲E̲T̲I̲O̲N̲ ̲(̲R̲E̲D̲E̲)̲
This command displays the associated format for Retrieval
Key D, described in section 5.3.5, which is the only
key type available for message deetion. Only messages
transmitted from this CAMPS site can be deleted.
5.7.1 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲ ̲O̲f̲ ̲R̲e̲t̲r̲i̲e̲v̲a̲l̲ ̲D̲a̲t̲a̲
Key data is entered as described in section 5.3.5 and
validated as described in section 5.3.7.
5.7.2 D̲e̲l̲e̲t̲i̲o̲n̲
Retrieved message can e viewed as described in section
5.4.3 and can be deleted/not deleted by entering "Y"/"N"
in the format fig. 5.7-2. If "Y" is entered, the message
is deleted and a Deletion Notification will be forwarded
to the user that requested the message to b deleted.
In any case, the Current Menu will be displayed.
If deletion cannot take place an error code is displayed.…86…1
…02… …02… …02… …02…
Fig. 5.7-2
Fig. 5.8-1…86…1 …02… …02… …02… …02…
5.8 R̲E̲S̲P̲O̲N̲S̲E̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲D̲I̲S̲P̲L̲A̲Y̲ ̲(̲R̲E̲S̲P̲)̲
If the supervisor selects the command "RESP" a message
from the response queue will be presented (on FIFO
basis). Messages requested retrieve from the off-line
Data Base are placed in the response queue by the system.
If no message is contained in the queue a system response
will be displayed.…86…1 …02… …02… …02… …02…
Fig. 6-1…01…Supervisor Engineering Functions…86…1 …02… …02… …02… …02…
6̲.̲ ̲ ̲S̲U̲P̲E̲R̲V̲I̲S̲O̲R̲ ̲E̲N̲G̲I̲N̲E̲E̲R̲I̲N̲G̲
The supervisor engineering commands are those engineering
functions implemented to work from the supervisor command
position.
6.1 S̲u̲p̲e̲r̲v̲i̲s̲o̲r̲ ̲E̲n̲g̲i̲e̲e̲r̲i̲n̲g̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲s̲
Two sets of Supervisor Engineering Functions have been
defined - the one set applies for normal mode of operation,
the other set applies where CAMPS is in restart mode
of operation.
6.2 N̲o̲r̲m̲a̲l̲ ̲M̲o̲d̲e̲ ̲(̲S̲E̲N̲F̲)̲
Entry of the Comman SENF will cause the System to display
the Engineering Menu (refer fig. 6.2.-1), listing the
Supervisor Engineering functions available.
6.2.1 S̲I̲C̲H̲ ̲C̲o̲m̲m̲a̲n̲d̲
The entry of the Command SICH will cause the system
to perform a system integrity check The result of
the integrity check will be printed at the supervisor
report printer as a part of the Command Completion
Report…86…1 …02… …02… …02… …02…
FIGURE 6.2-…86…1 …02… …02… …02… …02…
6.2.2 P̲M̲A̲N̲ ̲C̲o̲m̲m̲a̲n̲d̲
The entry of the Command PMAN will cause the system
to perform an analysis of the performance monitoring
data collected during the period since the previous
excution of the PMAN Command
6.3 R̲e̲s̲t̲a̲r̲t̲ ̲M̲o̲d̲e̲
In Restart Mode the only supervisor functions available
are those defined in the Restart Engineering Menu (refer
fig. 6.3-1). When the Supervisor signs on and the
system is in restart mode the menu isplayed will be
the Restart Engineering Menu.
FIGURE 6.3-1…86…1 …02… …02… …02… …02…
6.3.1 C̲a̲n̲c̲e̲l̲ ̲S̲y̲s̲t̲e̲m̲ ̲Q̲u̲e̲u̲e̲ ̲(̲C̲A̲S̲Q̲)
This command makes available the System Queue Cancel
Format (fig. 6.3.1-1). Cancellation via this format
is only allowed at restart.
6.3.1.1 D̲t̲a̲ ̲E̲n̲t̲r̲y̲
6.3.1.1.1 M̲D̲C̲O̲ ̲Q̲u̲e̲u̲e̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
For the max. 4 precedences entered here, cancellation
of messages etc. in the MDCO-Queue will be performed.
6.3.1.1.2 M̲e̲s̲s̲a̲g̲e̲ ̲S̲e̲r̲v̲i̲c̲e̲ ̲I̲n̲c̲o̲m̲i̲n̲g̲ ̲Q̲u̲e̲u̲e̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
For the max. 4 precedences entered hee, cancellation
of messages etc. in the specified queue will be performed.
6.3.1.1.3 M̲e̲s̲s̲a̲g̲e̲ ̲S̲e̲r̲v̲i̲c̲e̲ ̲O̲u̲t̲g̲o̲i̲n̲g̲ ̲Q̲u̲e̲u̲e̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
For the max. 4 precedences entered here, cancellation
of messages etc. in the specified queue will be performed.
.3.1.2 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
Error codes are displayed for invalid entries.
Fig. 6.3.1-1
6.3.2 C̲a̲n̲c̲e̲l̲ ̲A̲l̲l̲ ̲C̲i̲r̲c̲u̲i̲t̲ ̲Q̲u̲e̲u̲e̲s̲ ̲(̲C̲A̲A̲C̲)̲
This command can only be used at restart. It cancels
all Circuit-Queues in the system.
6.3.3 C̲a̲n̲c̲e̲l̲ ̲A̲l̲l̲ ̲T̲e̲r̲m̲i̲n̲a̲l̲ ̲Q̲u̲e̲u̲e̲s̲ ̲(̲C̲A̲A̲T̲)̲
This cmmand can only be used at restart. It cancels
all Terminal-Queues in the system.
6.3.4 C̲a̲n̲c̲e̲l̲ ̲A̲l̲l̲ ̲D̲e̲v̲i̲c̲e̲ ̲Q̲u̲e̲u̲e̲s̲ ̲(̲C̲A̲A̲D̲)̲
This command can only be used at restart. It cancels
all Device-Queues in the system.
6.3.5 C̲A̲C̲Q̲ ̲C̲M̲D̲ (Refer 4.5.7)
6.3. C̲A̲T̲Q̲ ̲C̲M̲D̲ (Refer 4.5.8)
6.3.7 C̲A̲D̲Q̲ (Refer 4.5.9)
6.3.8 C̲A̲G̲O̲ ̲C̲O̲M̲M̲A̲N̲D̲
Entry of the Command CAMPS GO will cause the system
(Supervisor) to exit the restart mode of operation.
The Restart Mode Engineering Functions will be available
no more.
6.3.9 O̲S̲P̲T̲ ̲C̲M̲D̲ (Refer 4.12.3)
6.3.10 S̲O̲D̲C̲ ̲C̲M̲D̲ (Refer 4.12.10)
Fig. 7.1-1…86…1 …02… …02… …02… …02…
7̲.̲ ̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲D̲I̲S̲T̲R̲I̲B̲U̲T̲I̲O̲N̲ ̲C̲O̲N̲T̲R̲O̲L̲
This section describes the Message Distribution Control
functions performed from the CAMPS MDCO position.
After entering of the command "MDCO, the MDCO Menu
will be presented.
7.1 M̲D̲C̲O̲ ̲F̲U̲N̲C̲T̲I̲O̲N̲S̲ ̲(̲M̲D̲C̲O̲)̲
Four functions can be selected by the Message Distribution
Control Menu (see fig. 7.1-2).
- Service Message Preparation
- Retrieval for Redistribution
- Message Distribution Assitance
- Response Message
7.1.1 C̲o̲m̲m̲a̲n̲d̲
The MDCO selects one of the options from the Menu by
entering a command.
7.1.2 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
If the entry is valid, the system replies by presenting
the appropriate format for the selected function.
f the entry is invalid, then the system replies by
representing the Message Distribution Control Menu
and displaying an error message in the system response
line.…86…1 …02… …02… …02… …02…
Fig. 7.1-2…86…1 …02… …02… …02… …02…
7.2 S̲E̲R̲V̲I̲C̲E̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲P̲R̲E̲P̲A̲R̲A̲T̲I̲O̲N̲ ̲(̲S̲M̲P̲R̲)̲
The Service Message Preparation functions available
for the MDCO are the same as for the supervisor. These
functions are described in secton 5.2.
7.3 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲R̲E̲D̲I̲S̲T̲R̲I̲B̲U̲T̲I̲O̲N̲ ̲(̲R̲E̲D̲S̲)̲
The MDCO Retrieval For Redistribution is identical
to that of the Supervisor and is described in section
5.6.…86…1 …02… …02… …02… …02…
Fig. 7.4-1…86…1 …02… …02… …02… …02…
7.4 M̲E̲S̲S̲A̲G̲E̲ ̲D̲I̲S̲T̲R̲I̲B̲U̲T̲I̲O̲N̲ ̲A̲S̲S̲I̲S̲T̲A̲N̲C̲E̲ ̲(̲M̲D̲A̲S̲)̲
If the MDCO selects the command "Message Distribution
assistance" in the Message Distribution control menu,
a message in the common mesage distribution queue will
be selected on FIFO basis. The terminal function field
which displays the name of the current transaction
will inform the MDCO which of the following actions
are being requested:
- Incoming Message assistance
- Alterative Distribution assistance
- Non deliverable objects from SCARS or CCIS
All fields within the Message format are protected
and the MDCO is not capable of modifying or correcting
the message.
The messages/comments will be presented in the folowing
formats:
- Incoming Messages - Format E…0f…1…0e…
- Outgoing Messages - Format E…0f…2…0e…
- Comments - Format G2
- Messages for coordination or Release from SCARS/CCIS
- SCARS/CCIS Format E…0f…1…0e….
If there is no message/comment in the common MDCO quee,
a system response message will be displayed in the
response line.…86…1 …02… …02… …02… …02…
Fig. 7.4.1-1…01…INCOMING MESSAGE DISTRIBUTION ASSISTANCE…86…1 …02… …02… …02… …02…
7.4.1 I̲n̲c̲o̲m̲i̲n̲g̲ ̲M̲e̲s̲s̲a̲g̲e̲ ̲A̲s̲s̲i̲s̲t̲a̲n̲c̲e̲
Incoming Messages are deferred to the MDCO position
for Incoming Message distribution assistance because
of the following reasons:
- Missing o garbled SICs
- Detection of Internal Handling Instructions
- Detection of Special Handling Instructions of category
exclusive or crypto security and no evidence of
a GR in FL10.
- Detection of more than one Special Handling Instruction.
- upervisor specified distribution to MDCO:
1) All incoming messages
2) All incoming messages of specified classification
3) All incoming messages except those of specified
classification
When performing Incoming Message Assistance, the format
hown in fig. 7.4.1-2 will be presented.
An annotation line will contain the reason why the
message was sent for assistance.
The system inserts Time Stamp (DTG) and Originating
Headquarters, so the SCD assignment can be referenced
to the message
7.4.1.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
7.4.1.1.1 S̲C̲D̲ ̲L̲i̲s̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The format contains the SCDs derived from the HQ/SIC/exercise
information if possible. The MDCO will be able to
delete SCDs from the list and to specify new SCDs to
which the message shall e distributed.
The SCD List which the MDCO makes at this time will
be the one which will be stored together with the message.
7.4.1.1.2 L̲o̲c̲a̲l̲ ̲P̲r̲i̲n̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The MDCO will be able to request a hard copy of the
distribution instruction. The Time Stamp and the Originating
headquarters ID are inserted sothe distribution instruction
can reference the message.
7.4.1.2 S̲e̲q̲u̲e̲n̲c̲e̲
7.4.1.2.1 P̲A̲G̲E̲-̲O̲N̲
After presentation of the SCD format, the message will
be presented when the PAGE ON key is depressed. The
MDCO can then page through the message.
7.4.1.2.2 P̲A̲G̲E̲ ̲B̲A̲C̲K̲
If the MDCO wants to return to the SCD format the PAGE
̲BACK key shall be depressed and further SCD updates
can be performed.
7.4.1.2.3 P̲R̲I̲N̲T̲
If the MDCO depresses the PRINT key, he will get a
hard copy of the message.
7.4.1.2.4 E̲N̲T̲E̲R̲
If the MDCO depresses the ENTER key, then the message
will be returned for further processing. If assistance
is needed again, the message will be returned to the
same MDCO position. After end distribution, the MDCO
will get the ext message from the common MDCO queue
displayed.
7.4.1.3 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
The system will validate the SCD lists entered by the
MDCO. If the validation fails, then the format is
returned with the errors indicated.…86…1 …02… …02…
…02… …02…
Fig. 7.4.1-2…86…1 …02… …02… …02… …02…
Fig. 7.4.2-1…01…ALTERNATIVE DISTRIBUTION ASSISTANCE…86…1 …02… …02… …02… …02…
7.4.2 A̲l̲t̲e̲r̲n̲a̲t̲i̲v̲e̲ ̲D̲i̲s̲t̲r̲i̲b̲u̲t̲i̲o̲n̲ ̲A̲s̲s̲i̲s̲t̲a̲n̲c̲e̲
Messages/comments are deferred to the MDCO position
for Alternative Distribution assistance because of
the following reasons:
- The mesage/comment cannot be delivered to all the
SCDs in the SCD list.
- Flash message/comment deferred because of time-out.
When performing Alternative Distribution assistance,
the format shown in Fig. 7.4.2-2 will be presented.
This format will sow the Terminal designators to which
distribution should have been carried out. The SCDs
to which distribution should have been carried out,at
the associated terminal, are presented together with
each designator (not applicable for printers). A dlivery
code is presented at the end of each line. By depressing
the function key "Display error Message" and then entering
the delivery code in the command line, the MDCO can
obtain a display of the delivery message in the response
line.
The sysem inserts Time Stamp (DTG) and Originating
Headquarters so the Alternative Distribution assignment
can be referenced to the message.
7.4.2.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
7.4.2.1.1 S̲C̲D̲ ̲L̲i̲s̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The MDCO will then be able to specify alternative SCDs
towhich the message shall be distributed. However,
this alternative distribution will not change the SCD
list which is stored together with the message.
7.4.2.1.2 L̲o̲c̲a̲l̲ ̲P̲r̲i̲n̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The MDCO will be able to request a hard copy of the
distribution instruction. The Time Stamp and the Originating
Headquarters ID are inserted sothe distribution instruction
can reference the message.
7.4.2.2 S̲e̲q̲u̲e̲n̲c̲e̲
7.4.2.2.1 P̲A̲G̲E̲ ̲O̲N̲
After presentation of the SCD format, the message will
be presented when the PAGE ON key is depressed. The
MDCO can then page through the message.
7.4.2.2.2 P̲A̲G̲E̲ ̲B̲A̲C̲K̲
If the MDCO wants to return to the SCD format, the
PAGE-BACK key shall be depressed and further SCD updates
can be performed.
7.4.2.2.3 P̲R̲I̲N̲T̲
If the MDCO depresses the PRINT key, he will get a
hard copy of the message.
7.4.2.2.4 E̲N̲T̲E̲R̲
If the MDCO depresses the ENTER key then the message
will be returned for further processing. If assistance
is needed again the message will be returned to the
same MDCO position. After end distribution, the MDCO
will get the net message from the common MDCO queue
displayed.
7.4.2.3 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
The system will validate the SCD lists entered by the
MDCO. If the validation fails, then the format is
returned with the errors indicated.…86…1 …02… …02…
…02… …02…
Fig. 7.4.2-2…86…1 …02… …02… …02… …02…
Fig. 7.4.3-1…86…1 …02… …02… …02… …02…
7.4.3 O̲b̲j̲e̲c̲t̲s̲ ̲Q̲u̲e̲u̲e̲d̲ ̲T̲o̲ ̲T̲h̲e̲ ̲M̲D̲C̲O̲
The following objects are queued to the MDCO:
- Objects received from SCARS and CCIS
- Objects from terminal queues due to security changes
i the terminal profiles (Refer section 4.2.1.2.2).
Objects from SCARS/CCIS of the following types will
be queued to the MDCO position if no valid SCD is recognized
and/or if the VDU page name is unknown:
- Messages for coordination
- Messages fr release
- Comments
- VDU pages
7.4.3.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
No entry of data.
7.4.3.2 S̲e̲q̲u̲e̲n̲c̲e̲
7.4.3.2.1 P̲R̲I̲N̲T̲
The MDCO will not be able to distribute these objects,
but only request a hard copy of the objects by depressing
the PRINT key.
7.4.3.2.2 S̲e̲n̲d̲ ̲C̲o̲m̲m̲e̲n̲t̲
The MDCO will also have the possibility of sending
a comment to SCARS or CCIS and requesting a retransmission
of the object with the correct SCD.
If the MDCO wants to send a comment, he must change
to user mode.
7.4.3.3 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
No validation is to be performed.
Fig. 7.5-1…86…1 …02… …02… …02… …02…
7.5 R̲E̲S̲P̲O̲N̲S̲E̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲D̲I̲S̲P̲L̲A̲Y̲ ̲(̲R̲E̲S̲P̲)̲
If the MDCO selects the command "RESP", a message in
the response queue will be displayed (on a FIFO basis).
Messages requested retrieved frm the off-line data
base are placed by the system in the MDCO response
queue.
Re-distribution of the messages can be continued (refer
to section 7.3).…86…1 …02… …02… …02… …02…
Fig. 8.1-1…86…1 …02… …02… …02… …02…
8̲.̲ ̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲S̲E̲R̲V̲I̲C̲E̲ ̲C̲O̲N̲T̲R̲O̲L̲
In this section Message Service Control at the MSO
position is described. Entry of "MSO" command will
cause presentation of MSO Menu.
8.1 M̲S̲O̲ ̲F̲N̲C̲T̲I̲O̲N̲S̲ ̲(̲M̲S̲O̲C̲)̲
One of the following functions can be selected from
the Message Service Menu.
- Service Message preparation
- Retrieval For Readdressal
- Retrieval For Rerun
- Outgoing Message Assistance Service
- Incoming Message AssistanceService
- Response Message
8.1.1 C̲o̲m̲m̲a̲n̲d̲s̲
The MSO selects one of the options from the menu by
entering a command.
8.1.2 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
If entry is valid, the appropriate format for the selected
function is displayed. On invalid entry Messag Service
Menu is displayed with error message in the system
response line.…86…1 …02… …02… …02… …02…
Fig. 8.1-2…86…1 …02… …02… …02… …02…
8.2 S̲E̲R̲V̲I̲C̲E̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲P̲R̲E̲P̲A̲R̲A̲T̲I̲O̲N̲ ̲(̲S̲M̲P̲R̲)̲
The MSO service message functions are identical to
the service message functions for the supervisor.
These are described in the SupervisorMessage Handling
procedures section 5.2.
8.3 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲R̲E̲A̲D̲D̲R̲E̲S̲S̲A̲L̲ ̲(̲R̲E̲A̲D̲)̲
Message Retrieval For Readdressal is similar to a Supervisor
function and is described in section 5.4.
8.4 R̲E̲T̲R̲I̲E̲V̲A̲L̲ ̲F̲O̲R̲ ̲R̲E̲R̲U̲N̲ ̲(̲R̲E̲R̲N̲)̲
Message Retrieval For Reru is similar to a Supervisor
function and is described in section 5.5.…86…1
…02… …02… …02… …02…
8.5 O̲U̲T̲G̲O̲I̲N̲G̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲S̲E̲R̲V̲I̲C̲E̲ ̲A̲S̲S̲I̲S̲T̲A̲N̲C̲E̲ ̲(̲O̲M̲A̲S̲)̲
If the command "Outgoing Message Service Assistance"
is selected, a message from the Outgoing Message Service
Queue is selected on IFO basis.
The required MSO action is displayed in the Information
Field.
- Outgoing RI Assignment
If there is no message in the Outgoing Message Service
Queue, a system response message is displayed.…86…1
…02… …02… …02… …02…
Fig. 8.5.1-1…01…Outgoing RI Assignment…86…1 …02… …02… …02… …02…
8.5.1 O̲u̲t̲g̲o̲i̲n̲g̲ ̲R̲I̲ ̲A̲s̲s̲i̲g̲n̲m̲e̲n̲t̲
Messages are deferred to the MSO position for Outgoing
RI Assignment for the following reasons.
- No channel open in this circuit
- No RI of prope classification could be found
- No circuit of proper classification could be found
- Too many RIs
- X-PLAs
- Unknown RI
User prepared messages deferred to the MSO position
for outgoing RI assignment will be displayed in Format
E2 and releasd messages from SCARS/CCIS will be displayed
in SCARS/CCIS format E1 and complete entered messages
from the PTR will be displayed in format E1.
The Routing List (see Fig. 8.5.1-2) will contain all
PLAs and associated RIs. The message is not yet eparated
and no transmissions of the message have been performed.
8.5.1.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
The System inserts the Time Stamp and originating Headquarters
ID, so the Outgoing RI-assignment can be referenced
to the message.
8.5.1.1.1 R̲I̲ ̲A̲s̲s̲i̲g̲n̲m̲e̲n̲t̲
The PLA List is created from the Action, Info and Exempt
field in format E…0f…2…0e…. All AIGs are converted to PLAs.
The PLAs will have associated an RI which is identified
by the system. If the PLA has no RI associated or
it is an X-PLA, the RI fiel will be empty. The MSO
is allowed to change the RIs in front of the PLA or
to insert one if the field is empty. If the MSO does
not insert an RI in front of an X-PLA, the PLA will
be skipped. On the contrary, the MSO must insert an
RI in front f a normal PLA. If this is not done, the
message will be returned with the error code corresponding
to unknown RI. The MSO is not able to change the PLAs,
but can precede the PLA with a ZEN prosign.…86…1
…02… …02… …02… …02…
8.5.1.1.2 P̲u̲n̲c̲h̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
If the MSO specifies punch in the format, the system
will, during the traffic separation, forward the message
copies, which cannot be transmitted, to te dedicated
PTP.
8.5.1.1.3 C̲l̲e̲a̲r̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
If the MSO specifies "clear" in the format, the system
will clear the message by insert of clear in format
line 12A. The message classification will be unchanged,
but the message attribute classifiction, which is the
classification used by the system, will be changed
to unclassified.
The MSO cannot specify both Punch and clear for the
message; if this is done, the message will be punched.
Clear can only be performed on user prepared messges.
8.5.1.1.4 E̲x̲t̲e̲r̲n̲a̲l̲ ̲A̲s̲s̲i̲g̲n̲e̲d̲ ̲T̲ ̲I̲n̲s̲t̲r̲u̲c̲t̲i̲o̲n̲s̲
Here the System enters the RIs contained in FL4 of
the message for Routing Assignment.
The first RI in the Relay Instruction is the Relaying
Station. If the Relaying Station shall receive a coy
of the message, the second field shall contain the
same RI as the first. The following four fields shall
contain the destination RIs which are used to perform
the Relaying by the Relaying station.
8.5.1.1.5 I̲n̲t̲e̲r̲n̲a̲l̲ ̲A̲s̲s̲i̲g̲n̲e̲d̲ ̲T̲ ̲I̲n̲s̲t̲r̲u̲c̲t̲i̲o̲n̲s̲ ̲(̲O̲t̲i̲o̲n̲a̲l̲)̲
The fields are the same as above except that the MSO
can enter a Relaying station and the destination(s).
The sum of T Instructions can maximum be 3.
8.5.1.1.6 L̲o̲c̲a̲l̲ ̲P̲r̲i̲n̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The MSO is able to request a hard copy of the RI-Assignment.
The Time Stamp and Originating Headquarters are inserted
by the system, so the RI-Asignment can be referenced
to the message.
8.5.1.2 S̲e̲q̲u̲e̲n̲c̲e̲
8.5.1.2.1 P̲A̲G̲E̲ ̲O̲N̲
After presentation of the outgoing RI assignment format,
the message will be presented when the PAGE ON key
is depressed. This way the MSO can page through the
mssage.
8.5.1.2.2 P̲A̲G̲E̲ ̲B̲A̲C̲K̲
By depressing the PAGE BACK key, the MSO can page back
through the message. If Outgoing RI Assignment, as
described in section 8.5.1.1, is desired, PAGE BACK
key is depressed until the Outgoing RI Assignment format
s displayed (No action if PAGE BACK key depressed again).
8.5.1.2.3 P̲R̲I̲N̲T̲
If the MSO depresses the PRINT key, he will get a hard
copy of the message.
8.5.1.2.4 E̲N̲T̲E̲R̲
If the MSO depresses the ENTER key, the message will
be returned for furher conversion. If assistance is
needed again, the message will be returned to the same
MSO position. After end conversion, the next message
from the common outgoing MSO queue is presented.
8.5.1.3 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
The system will validate the data in the Formats.
In cases where the message is protected, no validation
will be performed by the system.
The validation wil be performed when the MSO depresses
the ENTER key.
If the validation fails, then the format will be displayed
again indicating the error.…86…1 …02… …02… …02… …02…
Fig. 8.5.1-2…86…1 …02… …02… …02… …02…
Fig. 8.6-1…01…INCOMING MESSAGE SERVICE…86…1 …02… …02… …02… …02…
8.6 I̲N̲C̲O̲M̲I̲N̲G̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲S̲E̲R̲V̲I̲C̲E̲ ̲A̲S̲S̲I̲S̲T̲A̲N̲C̲E̲ ̲(̲I̲M̲A̲S̲)̲
If the command "Incoming Message Service Assistance"
is selected, a message from the Incoming Message Service
Queue is selected on IFO basis.
In the Information field, the required MSO transaction
is displayed and may be one of the following two functions:
- Garble correction
- Message inspection
If no message is found in the Incoming Message Service
Queue a system respnse message is displayed.…86…1
…02… …02… …02… …02…
Fig. 8.6.1-1…01…Garble Correction…86…1 …02… …02… …02… …02…
8.6.1 G̲a̲r̲b̲l̲e̲ ̲C̲o̲r̲r̲e̲c̲t̲i̲o̲n̲
The message presented for garble correction is in ACP127
format. (CCIS/SCARS in format E1).
All fields within that format are unprotected to allow
modiication and correction as required. The errors
detected during the analysis of the message header
will be indicated by an error code in the Margin Area
of the VDU screen.
If main errors are detected (e.g. non detectable format
lines), the ACP127analysis will be stopped and the
message will be queued for Message Service. Errors
contained in format lines after detection of main errors
will not be indicated. However, if a garbled message
is returned to the system, this will be detected by
he system during the new analysis and the message will
be presented again for further garble correction.
The MSO has the capability to direct an incoming garbled
message for outgoing message processing. If the message
contains external RIs in fomat line 2, when it is returned
from the MSO, then the system will transmit the message
in accordance with those RIs. It is the responsibility
of the MSO to ensure the validity of the RIs (external
RIs if transmission, only local RIs if no transmision)
in the corrected message else the message will be returned
for further MSO assistance.
8.6.1.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
8.6.1.1.1 E̲d̲i̲t̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The MSO edits header or text as appropriate. The whole
message is available by paging as necessary. on printable
characters are replaced by a suitable not normally
used character (e.g ).
8.6.1.1.2 A̲n̲n̲o̲t̲a̲t̲i̲o̲n̲ ̲(̲O̲p̲t̲i̲o̲n̲a̲l̲)̲
The MSO may generate an annotation which will be presented
together with the message at all terminals to which
distribution will be performed. Ths annotation is
stored together with the message.
8.6.1.2 S̲e̲q̲u̲e̲n̲c̲e̲
8.6.1.2.1 P̲R̲I̲N̲T̲
If the MSO depresses the PRINT key, a hard copy of
the message with the annotation will be printed.
8.6.1.2.2 E̲N̲T̲E̲R̲
If the MSO depresses the ENTER key, hen the message
will be returned for further analysis. If assistance
is needed again, the message will be returned to the
same MSO position. After end analysis, the next message
from the common Incoming MSO queue will be displayed
to the MSO.
.6.1.2.3 D̲E̲L̲E̲T̲E̲ ̲A̲N̲D̲ ̲P̲R̲E̲S̲E̲N̲T̲ ̲N̲E̲X̲T̲
If the MSO depresses the DELETE AND PRESENT NEXT, the
message will not be stored in CAMPS.
8.6.1.3 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
No validation will be performed during edit.…86…1
…02… …02… …02… …02…
Fig. 8.6.2-1…01……86…1 …02… …02… …02… …02…
8.6.2 M̲e̲s̲s̲a̲g̲e̲ ̲I̲n̲s̲p̲e̲c̲t̲i̲o̲n̲
The following messages shall be queued for Message
Inspection:
- Messages with Pilot
- Messages with incorrect Transaction Serial No.
- Messages withincorrect Channel Designator.
All fields within that format are protected, and the
MSO is not capable of modifying or correcting the message.
8.6.2.1 D̲a̲t̲a̲ ̲E̲n̲t̲r̲y̲
No data entry.
8.6.2.2 S̲e̲q̲u̲e̲n̲c̲e̲
8.6.2.2.1 P̲R̲I̲N̲T̲
If the MSO depresses thePRINT key a hard copy of the
message will be printed.
8.6.2.2.2 E̲N̲T̲E̲R̲
If the MSO depresses the ENTER key, then the message
will be returned for further analysis. If assistance
is needed again, the message will be returned to the
same MSO posiion. After end analysis the next message
from the common incoming MSO queue will be presented
to the MSO.
8.6.2.2.3 D̲E̲L̲E̲T̲E̲ ̲A̲N̲D̲ ̲P̲R̲E̲S̲E̲N̲T̲ ̲N̲E̲X̲T̲
If the MSO depresses the DELETE AND PRESENT NEXT, the
message will not be stored in CAMPS.
8.6.2.3 V̲a̲l̲i̲d̲a̲t̲i̲o̲n̲
Validation of data is not applicable.
Fig. 8.7-1…01…RESPONSE MESSAGE DISPLAY…86…1 …02… …02… …02… …02…
8.7 R̲E̲S̲P̲O̲N̲S̲E̲ ̲M̲E̲S̲S̲A̲G̲E̲ ̲D̲I̲S̲P̲L̲A̲Y̲ ̲(̲R̲E̲S̲P̲)̲
If the MDCO selects the command "RESP", a message from
the response queue will be displayed (on FIFO basis).
Messages requested retrieved frm the off-line Data
Base are placed in the MSO response queue by the system.
Readdressal and Rerun can be continued (refer to section
8.3 and 8.4).…86…1 …02… …02… …02… …02…
A̲P̲P̲E̲N̲D̲I̲X̲ ̲A̲ ̲-̲ ̲F̲I̲E̲L̲D̲/̲E̲L̲E̲M̲E̲N̲T̲ ̲D̲I̲C̲T̲I̲O̲N̲A̲R̲Y̲
N̲o̲t̲e̲s̲
1) S̲y̲n̲t̲a̲x̲
X = Any character
N = Numeric
A = Alpha
6A = Six alpha
6A…0f…n…0e… = n entries containing 6A
2) S̲e̲m̲a̲n̲t̲i̲c̲s̲
* = Item is defined NAME
NAME DEFINITION SYNTAX SEMANTICS
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲
PRECEDENCE SHORT The precedence with
which a 2A ZZ
FORM transaction shall be handled 00
PP
RR
PRECEDENCE LONG The precedence with which a 14A FLASH
FORM transaction shall be handled IMMEDIATE
PRIORITY
ROUTINE
FROM Designates th source of the
message it may contain
PLAIN LANGUAGE ADDRESS (PLA), or * *
PLA REFERENCE NUMBER * *
for a comment it contains
staff cell Designation (SCD) * *
PLAIN LANGUAGE The designator for the source/ 54X May be pre-
ADDRESS (PLA) destintion headquarters ceded by
an X
LOCAL PLA The designator for the Local 20X Max. 50
Headquarters
PLAIN LANGUAGE The unique number associated with 4N 1-3000
ADDRESS REFERENCE a headquarters PLA.
NUMBER (PLAREF)
CLASSIFICATION Used to define he classification 2A UU
SHORT FORM level of a message or comment RR
CC
SS
TT
CLASSIFICATION Expanded form of class used to 17A NATO UNCLASSIFIED
LONG FORM define level of a message or NATO RESTRICTED
comments NATO CONFIDENTIAL
NATO SECRET
COSMIC TOP SECRET
NAME DEFINITION SYNTAX SEMANTICS
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
SPECIAL HANDLING Defines a set of
special hand- 2A LL
INSTRUCTIO SHORT ling instructions
for messages DD
FORM PP
YY
(OTHERS UP
TO 20)
SPECIAL HANDLING Expanded set of special
handling 69X
INSTRUCTIONS instructions
LONG FORM
MHI Message Handling Instruction Code 3A
MESSAGE HANDLING Operating instrucions 50X Max.
20
INSTRUCTIONS inserted by the user consisting
of an Operating Signal +
parameter
PASSWORD Security feature. Entered during 8A
sign-on to terminal.
USER IDENTIFICA- Defines the user
uniquely to the 3X Max.
400
TION (USER ID) sytem. Restricts sign-on to
terminal with that user in its
profile
MESSAGE TYPE Reference number of the format of 4X
predefined message.
TRANSACTION ID Uniquely defines a transaction on
a terminal. Used as a reference for
logging purposes. It onsists of:
TERMINAL DESIGNATOR 3A
SERIAL NUMBER OF TRANSACTION 3N 000 999
TIMESTAMP * *
INTERNAL ITEM Uniquely defines an item for
RETRIEVE KEY retrieval and reference purposes
within CAMPS consists of:
ITEM REFERENCE IDENTITY * *
TIME TAMP * *
LINE NUMBER Specifies a line in the text part 3N 001 to 999
of a message. First line has
number 1.
NAME DEFINITION SYNTAX SEMANTICS
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
DEVICE TYPE Identify the type of a 3A MSP-
device LSP-
OCR- PTR-
PTP-
TERMINAL TYPE Identify the type of a 3A VDU
VDU
ITEM REFERENCE A serial number given to the 5N 00000 to
at
IDENTITY item during its life in CAMPS least 50.000
Together with a TIME STAMP it
defines a unique ITEM REFE-
RENCEidentity
TIME STAMP Defines the time for reference
purposes it consists of
DAY 2N 1 to 31
HOUR 2N 0 to 24
MINUTE 2N 0 to 59
ZONE SUFFIX 1A Z
(SPACE)
MONTH 3A First 3
letters of
month
(SPACE)
YEAR NN Last two
digits of
yearTO The
destination
addresses
if
a
message or comment.
For a message it consists of
ADDRESS INDICATOR GROUP, or *
ADDRESS GROUP, or *
PLAIN LANGUAGE ADDRESS, or 60X *
PLA REFERENCE NUMBER 4N *
For a comment it consists of
STAFF CELL DESIGNTOR 3A *
STAFF CELL The identity of a staff cell 3A Max. 400
DESIGNATOR (SCD) The staff cell identifiers
are
unique a CAMPS site.
NAME DEFINITION SYNTAX SEMANTICS
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
SUBJECT INDICATOR The subject indicator
code for 2A,3A Max.
390
CODE (SIC) the message
EXER/OPER This is an exercise name or
operation name defining the
context of the message it consists
of:
EXER/free text 77X free text
OPER/free text 106X free text
PERMISSIVE ENTRY 6X
CODE (PEC)
INTERNAL HANDLING ser to user instructions
69X…0f…n…0e… free
text
INSTRUCTIONS on how the message shall be
handled.
SUBJECT Subject of a message 69X…0f…n…0e… free text
TEXT Text of a message or comment 69X…0f…n…0e… free text
COORDINATE A list of staff cells with whom
coordintion is carried out. It
consists of:
Set of SCDs, and *
COORDINATION DESIGNATOR 3A(sp)…0f…10…0e…
LOCAL DISTN INFO A list of staff cells
designated
for local distribution. It con-
sists of a set of SCDs (3A)…0f…9…0e…
WINDOW A time window used to limitthe
search of a catalogue during
retrieval. It consists of:
HOURS 1N
MINUTES 2N
NAME DEFINITION SYNTAX SEMANTICS
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
ITEM TYPE Signifies the type of item in 1A R - RELEASED
a retrival request or catalogue MESSAGE
display D - DRAFT
OF
RELEASED
MESSAGE
L - LOCALLY
DISTRI-
BUTED
OUTGOING
MESSAGE
C - COMMENT
N - RELEASE
NOTIFI-
CATION
I - INCOMING
MESSAGE
ORIGINATOR SCD The Staff Cell Designator (SCD) 3A *
of the originator of a message or
comment as entered during prepara-
tion
ORIGINATOR ID The name, rank and personal 20X free text
identifier of the oriinator
TOC Time of occurrence is a TIME 14X *
STAMP
SECURITY 5A
WARNING CODE
ADDRESS INDICATOR A group of PLAs AIG
4N 0001-9999
GROUP (AIG) (Maximum 200 AIGs)
CHANNEL An unique identifier
of an 3A 64
(two
per
DESIGNATOR (CD) exteral channel channel).
CHANNEL SERIAL NO The number associated
with the 3N
or 001
-
999
3 character Channel Designator 4N 001 - 9999
COMMAND Supervisor command 4A See list
of
commands
EXPIRATION TIME Expiration date for passwords 6N DDMMYY
RUTING An identifier of a routing 4A, 5A...9A
INDICATOR (RI) network and a destination Max. 15 in
local/RI-table
Max. 3000
in
RI-table…86…1
…02…
…02…
…02…
NAME DEFINITION SYNTAX SEMANTICS
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
TERMINAL An identifier of a terminal 3A Max. 32
DESIGNATOR (TD) osition
VOLUME NAME An identifier of a disk pack 1X,2X...16X
(VOL-ID)
SECURITY WARNING Warning text entered
on handling 1X,2X...500X
TEXT a message of specified
classification
ZONE LETTER Letter specifying a time zone 1A (Z)
CIRCUIT NO No idenifying a circuit 2N 01-27
ADDRESS GROUP A group of PLAs
(AG) (Max. 200 AGs) 1A,2A...4A
DEVICE DESIGNATOR A unique identifier of a 3A max. 43
(DD) device
STANDARD DISTRI- Identifies a set
of INFO and 3N 1-800
BUTION LIST (SDL) ACTION SCDs.
DISPLY ID An identifier of a 8X max. 300
VDU display
CONFIRMATION 2A
CODE (CC)…86…1 …02… …02… …02…
A̲P̲P̲E̲N̲D̲I̲X̲ ̲B̲:̲ ̲ ̲S̲Y̲S̲T̲E̲M̲ ̲R̲E̲P̲L̲Y̲ ̲M̲E̲S̲S̲A̲G̲E̲S̲
Invalid Sign-On
Permissive Entry Code Required
Notification of Message Deletion
Invalid Entry
Item Referred To Is Non-Existent
TOC-Window Must Be Less Than 6 Hours
Not Found Try Again
Retrieval In Progress, Please Wait
Queue Is Empty
Enter Confirmation Code
Note: List not complete…86…1 …02… …02… …02… …02…
A̲P̲P̲E̲N̲D̲I̲X̲ ̲C̲:̲ ̲ ̲L̲I̲S̲T̲ ̲O̲F̲ ̲C̲O̲M̲M̲A̲N̲D̲S̲
A̲C̲T̲I̲O̲N̲ ̲F̲I̲E̲L̲D̲ ̲D̲E̲S̲C̲R̲I̲P̲T̲I̲O̲N̲
A̲C̲T̲I̲O̲N̲ A̲C̲T̲I̲O̲N̲ ̲E̲F̲F̲E̲C̲T̲
C (COMMAND) - PEC
-Transaction Id, Log of action
- Completion Code, Command Completion
Report
P (PROCEDURE) - Transaction Id, Log of action
M (MENU) No action applicability…86…1 …02…
…02… …02… …02…
M̲N̲E̲M̲O̲N̲I̲C̲ A̲C̲T̲I̲O̲N̲ D̲E̲S̲C̲R̲I̲P̲T̲I̲O̲N̲ P̲A̲R̲A̲M̲E̲T̲E̲R̲
ABOL C Abandon
Off-Load
ABRO C Abandon
Reorganization
ACPC C CP127
Parameter
Control
ADSC M Addressing
Scheme
Control
AIGP P AIG
Table
Print
AIGT C AIG
Table
Update -
AIG
ASSG P Supervisor
Assign
Command
BLCQ C Block
Queue
For
This
Circuit -
Circuit
#
BLDQ C Block
Queue
For
This
Device -
Device
Designaor
BLTQ C Block
Queue
For
This -
Terminal
Designator
Terminal
CAAC C Cancel
All
Circuit
Queues
At
Restart
CAAD C Cancel
All
Device-Queues
At
Restart
CAAT C Cancel
All
Terminal
Queues
At
CACQ C Circuit
Queue
Cancellation -
Circuit
#
ADQ C Device
Queue
Cancellation -
Device
Designator
CAPP P Continue
Abbreviated
Plaindress
Preparation
CASP P Continue
Abbreviated
Service
Message
Preparation
CASQ C System
Queue
Cancellation
At
Restart
CATQ C Terminal
Queue
Cancellaion -
Terminal
Designator
CHAC C Channel
Control -
Channel
Designator
CHPC C Channel
Parameter
Control
CIOF C Set
Crisis
Indicator
Off
CION C Set
Crisis
Indicator
On
CIRP P Circuit
Table
Print
CIRT C Circuit
Table
Update -
Circuit
#
CMDC C Cmmand
Control -
Command
Code
CMPT C Command
Print
COPY C Copy
System
Parameter
File
CPFP P Continue
Plaindress
Preparation
CPPT P Channel
Profile
Print -
Channel
Designator
DESM P Delete
Service
Message
DEVC M Device
Control
DISC M Disc
ontrol
DPPT P Device
Profile
Print -
Device
Designator
FLQT C Set
Flash
Queue
Time
Out -
Time
Period
GNSC M Global
No
Series
Control
GPLP P Global
PLA
Table
Print
GPLT C Global
PLA
Table
Update -
PLAREF
IMAS P Incoming
Message
Service
Assstance…86…1…02…
…02…
…02…
…02…
M̲N̲E̲M̲O̲N̲I̲C̲ A̲C̲T̲I̲O̲N̲ D̲E̲S̲C̲R̲I̲P̲T̲I̲O̲N̲ P̲A̲R̲A̲M̲E̲T̲E̲R̲
LGLL P CLOSE
LOG
CIF
LGTR P Log
Trace
LORI C Local
RI-Table
Update
LORP P Local
RI-Table
Print
LPLP P Local
PLA-Table
Print
LPL C Local
PLA-Table
Update -
PLAREF
MDAS P Message
Distribution
Assistance
MDCO M Message
Distribution
Control
MDPC C Message
Distribution
Parameter
Control
MSGH M Message
Handling
MSOC M Message
Service
Control
NOCC C Channel
No
Series
Conrol -
Channel
Designator
NOSC C System
No
Series
Control
NOTR C Transaction
No
Series
Reset -
Terminal
or
Device
Designator
OFLD C Off-Load
Until
"Time" -
Time,
Vol-ID
OMAS P Outgoing
Message
Service
Assistance
OPST C Operating
Signa
Table
Update -
MHI
OROF C Off-Line
Retrieval
Off
ORON C Off-Line
Retrieval
On
ORSU C Off-Line
Retrieval
Suspend
OSMS P Outgoing
Service
Message
Status
POSC C PT/OCR/SATP
Control -
Device
Designator,
-
Device
Type
PPPC C Print/Punch
Paramter
Control
PRAP P Prepare
New
Abbreviated
Plaindress
Message
PRAS P Prepare
New
Abbreviated
Service
Message
PRPF P Prepare
New
Plaindress
Message
PWLT C Password
List
QSPT P Queue
State
Print
QUEC M Queue
Control
READ P Retrieval
Fo
Readdressal
REDE C Retrieval
for
Deletion
REDS P Retrieval
For
Redistribution
RELU P Retrieval
For
Local
Use
REMO C Refuse
Mount
Of
Volume -
Volume
ID
REOR C Reorganize
All
Tables
RERN P Retrieval
For
Rerun
RESP P Response
Message
RITA C R
Table
Update -
RI
RITP P RI
Table
Print
SCCP P Display
Table
Print-Out
SCCT C Display
Table
Update -
Display
ID
SCDP P SCD
Table
Print
SCDT C SCD
Table
Update -
SCD…86…1…02…
…02…
…02…
…02…
M̲N̲E̲M̲O̲N̲I̲C̲ A̲C̲T̲I̲O̲N̲ D̲E̲S̲C̲R̲I̲P̲T̲I̲O̲N̲ P̲A̲R̲A̲M̲E̲T̲E̲R̲
SDLP P SDL
Table
Print
SDLT C SDL
Table
Update
-
SDL
SDPC C Special
Distribution
Parameter
Control
SECC C Security
Control
SNF M Supervisor
Engineering
SICP P SIC
Table
Print
SICT C SIC
Table
Update -
SIC
SIOF P Sign-Off
SION P Sign-On
SMPR M Service
Message
Preparation
SPAP P System
Parameter
Print
SQHO C Set
Quiet
Hours
Off
SQHT C Set
Quiet
Hour
Terminal -
Terinal
Designator
STOC P Storage
Occupance
Request
SUPC C Supervisor
Print
Control
SUPV M Supervisor
Control
SYIE M System
Information
Extract
SYPC M System
Parameter
Control
SYSC M System
Control
TAPR M Table
Print
TEPC C Terminal
Position
Cntrol -
Terminal
Designator
TPPT P Terminal
Profile
Print -
Terminal
Designator
TSTP P Table
Status
Print
UBCQ C Unblock
Queue
For
This
Circuit -
Circuit
#
UBDQ C Unblock
Queue
For
This
Device -
Device
Designator
UBTQ C Unblock
Queue
For
This
Terminal
Designator
Terminal
UPPT P User
Profile
Print -
User
ID
UPUP C User
Profile
Update -
User
ID
USER M User
VODL C Delete
Volume -
Volume
ID
VODM C Dismount
Volume -
Volume
ID
VOLI C List
Volumes
Currently
In
Use
VOMO C Mount
Volme -
Volume
ID
VONM C Name
Volume -
Volume
ID
VSMO C Mount
Volume
For
System
Use -
Volume
ID
