top - download
⟦a6ce5a786⟧ Wang Wps File
Length: 4699 (0x125b)
Types: Wang Wps File
Notes: Spelunked
Names: »~ORPHAN66.00«
Derivation
└─⟦61695b6f0⟧ Bits:30006170 8" Wang WCS floppy, CR 0291A
└─ ⟦this⟧ »~ORPHAN66.00«
WangText
Z…00……00……00……00…B…02……00……00…B
B…05…A…08…A…0d…A…00…A @…09…@…0c…@…0d…@…02…@…07…?…0b…?…00…? >…09…>…0a…>…0e…>…01…>…05…=…0a…=…0e…=
=…07…<…0b…<…00…<…05…;…08…;…0d…;…01…;…05…:…09…:…0d…:…02…:…06…9…0b…9…00…9…05…8…0a…8…0f……86…1 …02… …02… …02…
2891A/rt …02… CPS/OPM/003
…02… CLA/840801…02……02…
CAMPS MDCO OPERATION MANUAL
…02… Issue 2 …02…CAMPS
2.3.3 Initial Setup
1 Verify that the MSP is Figure 2.2.3-1.a.
installed and connected
and that the circuit breaker
and power switch are OFF.
2 Verify hat the ribbon is Refer to Sec. 2.2.2.
properly installed.
3 Load the unit with Refer to Sec. 2.2.2.
paper.…86…1 …02… …02… …02… …02…
2.3.3 Initial Setup (cont'd)
4 Turn the audio control Refer to Figure
2.2.3-2.a.
on the front panel
to the
loudest position.
5 Set all facility circuit Refer t Figure 2.2.3-1.a.
breakers for this set
to ON. Set the TCM power
switch to ON.
6 Verify that the POWER lamp Refer to Figure
2.2.3-2.b.
on the front panel lights.
7 Insert the security key in Refer to Figure
2.2.3-2.c.
the key-lock an turn to
the ON position.…86…1 …02… …02…
…02… …02…
2.3.3 Initial Setup (cont'd)
8 Depress the LINE FEED push Refer to Figure
2.2.3-3.a.
button on the TCM front Verify that one
line feed
panel for at least one of papr occurs,
followed by
second. continuous line
feeds for as
long as the LINE
FEED push
button is depressed.
9 Continue to depress the Refer to Figure
2.2.3-3.a.
LINE FEED push button for
single line feeds until
the serrated edge of oe
sheet passes the print-
head by 3 to 6 lines.
10 Depress the FORM FEED button Refer to Figure
2.2.3-3.b.
on the TCM front panel. Verify the paper
feeds to the same
popsition on the
next sheet. This
operation establishes
the form feed posiion.
11 Depress the TEST push button Refer to Figure
2.2.3-3.c.
on the TCM front panel for Verify that the
following
at least 5 seconds. is printed:
NO ERRORS IN ROM
NO ERRORS IN RAM
(Printer prints
66 lines barberpole
pattern). (Tere
may be a time delay
between printouts).…86…1
…02… …02…
…02… …02…
2.3.3 Initial Setup (cont'd)
The MSP is now ready
to receive message
traffic from the
line. Arrange to
have one or more
messages sent to
the MSP and verify
message cotent with
the transmitting
station. During
this time, the key-lock
switch should be
tested by setting
it to the OFF position
and verifying printing
has stopped. The
CAMPS system is
able to verify when
the switch has been
set to ON.
12 Set the keylock switch to Refer to Figure
2.2.3-4.a.
OFF.
13 Remove the key. Refer to Figure
2.2.3-4.a.
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
^W̲A̲R̲N̲I̲N̲G̲^ Do not operate the
MSP with the cover open.…86…1 …02… …02…
…02… …02…
3.1.1 Sign On (SION) (cont'd)
After the boot sequence
and start up procedure
from the maintenance
position is finished,
the system will
present you for
a standard layut
on the VDU screen.
Refer to Figure
3.1.1-1.
1 On keyboard, press the Refer to Figure
3.1.1-2.a.
control function key- Pressing the ATTN-key
causes
ATTN the VDU to present
ENTER in the system
line. The cursor
will be found in
the system ine and
await a command
code.
2 On keyboard, enter the
command code SION.
3 Press ENTER key Refer to Figure
3.1.1-2.a.
4 On keyboard, enter your The identification
code and
3 letter ID code and the password will
NOT be
your 8 letter pasword. displayed on the
screen.
Comma or space are
used as
separator.
5 Press ENTER key Refer to Figure
3.1.1-2.b.
3.1.1 Sign On (SION) (cont'd)
6 If you enter invalid ID Blocking the terminal
will
code or password, you must take place after
three
go back to step 4 and try invald attempts.
again.
7 If the terminal displays If the actual terminal
also
BLOCKED in the response have supervisor
capability,
line, proceed either to real blocking of
the terminal
step 1 and try again or will never take
place. You
contat supervisor for must press the Attn-key,
further help. which will bring
you back
Otherwise, proceed to to sign on mode
again.
step 8. Otherwise, you must
contact supervisor
for further help.
8 Proceed either to sec- When the sign-on
procedre
tion HIGH LEVEL MENU is OK, the system
will pre-
or section SECURITY sent you for the
high level
PROCEDURES, dependent menu or the MDCO
menu.
on what the system If high level menu
is
displays. presented proceed
to the high level
menu
