top - download
⟦ab5071cc8⟧ Wang Wps File
Length: 6246 (0x1866)
Types: Wang Wps File
Notes: CPS/TPR/018 (Insp.& Test)
Names: »1677A «
Derivation
└─⟦0c861a53d⟧ Bits:30006079 8" Wang WCS floppy, CR 0122A
└─ ⟦this⟧ »1677A «
WangText
…02…CPS/TPR/018
…02… EV/820210…02……02…#
INSPECTION AND TEST PROCEDURE FOR
ARC V24/V28 L/L ADAPTERS…02……02…CAMPS
T̲A̲B̲L̲E̲ ̲O̲F̲ ̲C̲O̲N̲T̲E̲N̲T̲S̲
1 SCOPE ........................................
4
1.1 DEFINITION ...............................
4
2 APPLICABLE DOCUMENTS .........................
4
3 INCOMING INSPECTION .........................
5
3.1 GENERAL ..................................
5
3.1.1 Registration .........................
5
3.1.2 Failure Reporting ....................
5
3.1.3 Documentation ........................
5
3.1.3.1 Invoice and COC's ................
5
3.2 INCOMING INSPECTION LOG ..................
5
4 VISUAL INSPECTION ............................
6
4.1 GENERAL ..................................
6
4.1.1 Inspection Points ....................
6
5 TEST EQUIPMENT ...............................
6
6 D-CONNECTORS .................................
7
6.1 D-CONN. ..................................
7
6.2 EDGE-CONN. TO TOGGLE-SWITCH ..............
7
7 TEST-CONFIGURATION ...........................
8
8 FUNCTIONAL TEST ..............................
8
8.1 POWER SUPPLY TEST ........................
8
8.2 OUTPUT TEST ..............................
9
APPENDIX A: INCOMING INSPECTION LOG ............ A1
APPENDIX B: TEST CONFIGURATION ................. B1
1 S̲C̲O̲P̲E̲
Described herein are inspections and tests to be done
to the V24/V28 line-to-line adapters delivered from
Atlantic Research Corporation to Christian Rovsing
A/S.
1.1 D̲E̲F̲I̲N̲I̲T̲I̲O̲N̲
T̲Y̲P̲E̲ ̲ ̲ ̲ ̲V̲E̲R̲S̲I̲O̲N̲ ̲ ̲ ̲ ̲ ̲ ̲B̲U̲I̲L̲T̲-̲I̲N̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲Q̲U̲A̲N̲T̲I̲T̲Y̲ ̲ ̲ ̲
4 CH 1 2M CAMAC 118
1 CH 2 1M CAMAC 100
2 A̲P̲P̲L̲I̲C̲A̲B̲L̲E̲ ̲D̲O̲C̲U̲M̲E̲N̲T̲S̲
SD/STD/017
Incoming Inspection Standard
PAD/PRC/002
Non-Conformance Handling
Acceptance Test Procedure
Date: Revision 1 December 8, 1981
CPS/AUX/009
Quality Requirements for Equipment
Purchased for the CAMPS Project
3 I̲N̲C̲O̲M̲I̲N̲G̲ ̲I̲N̲S̲P̲E̲C̲T̲I̲O̲N̲
3.1 G̲E̲N̲E̲R̲A̲L̲
Unpacking, registration, inspection for shipping damage,
and visual inspection of the modules shall be performed
by the ILS-Incoming Inspection Personnel.
3.1.1 R̲e̲g̲i̲s̲t̲r̲a̲t̲i̲o̲n̲
Registration shall be performed in agreement with the
lines laid down in SD/STD/017, Incoming Inspection
Standard.
3.1.2 F̲a̲i̲l̲u̲r̲e̲ ̲R̲e̲p̲o̲r̲t̲i̲n̲g̲
All failures, discrepancies etc shall be reported in
agreement with the lines laid down in PAD/PRC/002 Non-Conformance
Handling.
3.1.3 D̲o̲c̲u̲m̲e̲n̲t̲a̲t̲i̲o̲n̲
3.1.3.1 I̲n̲v̲o̲i̲c̲e̲ ̲a̲n̲d̲ ̲C̲O̲C̲'̲s̲
Invoice and Certificates of Conformance shall in copies
be distributed to the Project Office.
3.2 I̲N̲C̲O̲M̲I̲N̲G̲ ̲I̲N̲S̲P̲E̲C̲T̲I̲O̲N̲ ̲L̲O̲G̲
The Incoming Inspection Log Appendix A shall be filled
in consistent and carefully during the whole inspection
and test operation. This log will be an appendix to
the concerned Incoming Inspection Report (IKR).
4 V̲I̲S̲U̲A̲L̲ ̲I̲N̲S̲P̲E̲C̲T̲I̲O̲N̲
4.1 G̲E̲N̲E̲R̲A̲L̲
The following visual inspection points shall be inspected
by the ILS-Inspection personnel.
4.1.1 I̲n̲s̲p̲e̲c̲t̲i̲o̲n̲ ̲P̲o̲i̲n̲t̲s̲
a) Verify that all ordered items are presented.
b) Inspect the modules for possible shipping damage.
c) Verify that the workmanship is in accordance with
CPS/AUX/009.
5 T̲E̲S̲T̲ ̲E̲Q̲U̲I̲P̲M̲E̲N̲T̲
The following test equipment will be utilized during
the test:
a) Oscilloscope, Tektronix 465.
b) Communication Tester, Tektronix 834.
c) Multimeter, Fluke 8020A.
d) Pulse-generator, Philips PM5715.
e) Adapter Power Supply, Metrix.
6 D̲-̲C̲O̲N̲N̲E̲C̲T̲O̲R̲S̲
The configuration of the connectors with interconnection-cable-length
is shown in Appendix B.
6.1 D̲-̲C̲O̲N̲N̲.
The following links on the D-connectors:
F̲O̲U̲R̲ ̲L̲O̲O̲P̲-̲B̲A̲C̲K̲ ̲R̲S̲2̲3̲2̲
PIN 2-3
PIN 6-20
PIN 5-8
6.2 E̲D̲G̲E̲-̲C̲O̲N̲N̲.̲ ̲T̲O̲ ̲T̲O̲G̲G̲L̲E̲-̲S̲W̲I̲T̲C̲H̲
To indicate connection to card edge receptable (dual
43): notation A or B refers to sides of board.
The following links on the edge-connector to the toggle-
switch are made:
B7 - B8
A6 - A7
B16 - B15
A14 - A15
B24 - B25
A23 - A24
B32 - B33
A31 - A32
A27 - B27 (ground)
A8 - A16 - A25 - A33
7 T̲E̲S̲T̲-̲C̲O̲N̲F̲I̲G̲U̲R̲A̲T̲I̲O̲N̲
The test-configuration is shown in Appendix B.
The L/L-adapter under test is connected to the loop-back
cable.
All four D-connectors are used on the 4-channel version.
The 2x9 VAC is supplied from a Metrix Adapter Power
Supply to the edge connector A/B pin 9 and A/B pin
26. The pulse-generator is connected to the loop-back
cable input and a dual-channel oscilloscope is monitoring
the input and using a flying probe measuring the 15
output pins.
8 F̲U̲N̲C̲T̲I̲O̲N̲A̲L̲ ̲T̲E̲S̲T̲
8.1 P̲O̲W̲E̲R̲ ̲S̲U̲P̲P̲L̲Y̲ ̲T̲E̲S̲T̲
Measure the voltage and ripple on plug U1 between ground
connection and:
PIN 16 to be within +12V 5%, RIPPLE 50mV
PIN 9 to be within -12V 5%, RIPPLE 50mV
PIN 3 to be within + 5V 5%, RIPPLE 1mV
Vary the input from the mains plus and minus 15% and
control that the above mentioned voltages are still
within 5%.
8.2 O̲U̲T̲P̲U̲T̲ ̲T̲E̲S̲T̲
Connect the pulse-generator to the input A8 and adjust
the generator to supply 600 Hz square wave plus/minus
2.2V amplitude.
Connect an oscilloscope between ground and the test-points
mentioned in the Incoming Inspection Log.
Measure the output amplitude to be within 5.5V to
6.5V (11Vpp - 13Vpp).
Measure the risetime to be:
a) VERSION 1: 80 usec plus/minus 20%.
b) VERSION 2: 10 usec plus/minus 20%.
