top - download
⟦b7bdefa47⟧ Wang Wps File
Length: 5641 (0x1609)
Types: Wang Wps File
Notes: CPS/TPR/047
Names: »4831A «
Derivation
└─⟦f44499b45⟧ Bits:30006204 8" Wang WCS floppy, CR 0303A
└─ ⟦this⟧ »4831A «
WangText
4831A/al…02…CPS/TPR/047
…02…FLY/840412…02……02… #
INSPECTION AND TEST PROCEDURE
FOR V24 MONITOR MODULES…02……02…CAMPS
CAMPS
INSPECTION AND TEST PROCEDURE
FOR V24 MONITOR MODULES
CPS/TPR/047
Flemming Lydeking
Kurt Nybro-Nielsen
KNN, OWE, PMS, LU, FLY, IJO, GQAR, QA, BB
…0f… CPS QA H/W 840412
ILS Maint. Mgr. 840524
1 ILS Config.Mgr. 840524
840412…0e…
4831A/al…02… CPS/TPR/047
INSPECTION AND TEST PROCEDURE…02… FLY/840412…02……02…ii
FOR V24 MONITOR MODULES
…02……02… CAMPS
840412 All Initial issue of document
4831A/al…02…CPS/TPR/047
…02…FLY/840412…02……02…iii
INSPECTION AND TEST PROCEDURE
FOR V24 MONITOR MODULES…02……02… CAMPS
T̲A̲B̲L̲E̲ ̲O̲F̲ ̲C̲O̲N̲T̲E̲N̲T̲S̲
1 SCOPE ........................................
1
2 APPLICABLE DOCUMENTS .........................
2
3 VISUAL INSPECTION ............................
3
3.1 INSPECTION POINTS ........................
3
4 TEST EQUIPMENT ...............................
3
5 TEST CONFIGURATION ...........................
4
5.1 TEST CONNECTION ..........................
4
6 FUNCTIONAL TEST ..............................
5
6.1 POWER SUPPLY .............................
5
6.2 OUTPUT ...................................
5
6.3 PULSE TRAP ...............................
6
6.4 TEST REPORT ..............................
6
7 FRONT PANEL (Figure 6.3-1) ...................
7
APPENDIX A: Test Configuration A1 .............
8
APPENDIX B: Test Report B1 ....................
9
1 S̲C̲O̲P̲E̲
This document describes the procedure for inspection
and test of V24 Monitor Module.
2 A̲P̲P̲L̲I̲C̲A̲B̲L̲E̲ ̲D̲O̲C̲U̲M̲E̲N̲T̲S̲
SD/STD/017
INCOMING INSPECTION STANDARD
PAD/PRC/0002
NON-CONFORMANCE HANDLING
CPS/AUX/009
QUALITY REQUIREMENTS FOR EQUIPMENT
PURCHASED FOR THE CAMPS PROJECT
3 V̲I̲S̲U̲A̲L̲ ̲I̲N̲S̲P̲E̲C̲T̲I̲O̲N̲
3.1 I̲N̲S̲P̲E̲C̲T̲I̲O̲N̲ ̲P̲O̲I̲N̲T̲S̲
a) Inspect the module for possible damage.
b) Verify that the workmanship is in accordance with
CPS/AUX/009.
4 T̲E̲S̲T̲ ̲E̲Q̲U̲I̲P̲M̲E̲N̲T̲
The following test equipment will be utilized during
the test.
a) Pulse-generator, Philips PM 5715
b) Multimeter, Fluke 8020A
c) Adapter Power Supply, Metric
d) Test Adapter, CR
e) Test box, CR
5 T̲E̲S̲T̲ ̲C̲O̲N̲F̲I̲G̲U̲R̲A̲T̲I̲O̲N̲
5.1 T̲E̲S̲T̲ ̲C̲O̲N̲N̲E̲C̲T̲I̲O̲N̲
The test configuration is shown in appendix A.
All inputs to the V24 Monitor Module are interfacing
through a test adapter making it easy to replace the
board under test with another one to be tested.
The V24 Monitor Module requires a 2x9 VAC power supply,
which is supplied from the adapter power supply (ref.
sec. 4).
The necessary test signal is supplied from the pulse
generator (ref. sec. 4) connecting to the Test Adapter.
A rotary switch on the Test Adapter connects the generator
to the selected input on the V24 Monitor Module.
6 F̲U̲N̲C̲T̲I̲O̲N̲A̲L̲ ̲T̲E̲S̲T̲
6.1 P̲O̲W̲E̲R̲ ̲S̲U̲P̲P̲L̲Y̲ ̲T̲E̲S̲T̲
Measure the voltage between ground connection and:
Cap. C3/+ to be within + 13C +̲ 10%
Cap. C5/- to be within - 13V +̲ 10%
Cap. C2/+ to be within + 5V +̲ 5%
6.2 O̲U̲T̲P̲U̲T̲ ̲T̲E̲S̲T̲
Connected the pulse generator to input on the test
adapter and adjust the generator to supply 600 Hz square
wawe plus/minus 2.2V amplitude.
a) Connect the Test Box to connector Ch. 1 on V24
Monitor Module.
b) Connect the pulse generator to Ch. 1 on the Test
Adapter.
c) Set channel switch on V24 Monitor Module to Ch.
1.
d) Now all inputs on the channel concerned are tested
sequentially.
Select the input to be tested by the rotary switch
on the Test Adapter. Inspect visually that the
relevant LED's on the front panel and test box
are turned on/off corresponding to the signal input.
e) Repeat steps a to d testing channel 2,3 and 4 respectively.
6.3 P̲U̲L̲S̲E̲ ̲T̲R̲A̲P̲ ̲T̲E̲S̲T̲
Disconnect the pulse generator, reset the pulse trap
and connect a cable to C2/+.
Now the switch S1 (ref. Figure 6.3-1) is set to position
"1" and switch S2 to position marked "6".
The cable is connected to the input of the Test Adapter
corresponding to the actual switch setting, and it
is visually tested if the LEDs marked "+" and "-" are
turned on.
This procedure is repeated for all combinations of
switch settings of S1 and S2.
6.4 T̲E̲S̲T̲ ̲R̲E̲P̲O̲R̲T̲
All test results shall be reported in a Test Report
(ref. appendix B).
Figure 6.3-1
A̲P̲P̲E̲N̲D̲I̲X̲ ̲A̲…01……01…TEST CONFIGURATION
A̲P̲P̲E̲N̲D̲I̲X̲ ̲B̲…01……01…INSPECTION AND TEST
