top - download
⟦c6cc679c5⟧ Wang Wps File
Length: 6301 (0x189d)
Types: Wang Wps File
Notes: BACK PANEL TYPE 8,CR1100
Names: »1216A «
Derivation
└─⟦2a70d8cf1⟧ Bits:30006046 8" Wang WCS floppy, CR 0073A
└─ ⟦this⟧ »1216A «
WangText
…02…CPS/TCM/001
…02…CSV/820714…02……02…#
BACK PANEL TYPE 8, CR 1100
TECHNICAL MANUAL…02……02…CAMPS
L̲I̲S̲T̲ ̲O̲F̲ ̲C̲O̲N̲T̲E̲N̲T̲S̲
1. INTRODUCTION ...................................
4
1.1 MODULE STATUS ..................................
6
2. INTERFACE SPEC. ................................
8
2.1 INTERFACE SIGNAL SPEC. .........................
8
2.2 ELECTRICAL INTERFACE SPEC. .....................
9
2.3 MECHANICAL INTERFACE SPEC. .....................
9
3. BLOCKED SCHEMATIC ..............................
11
4. PARTS LIST .....................................
13
5. MECHANICAL DRAWINGS ............................
16
6. ACCESSORIES ....................................
21
1̲ ̲ ̲I̲N̲T̲R̲O̲D̲U̲C̲T̲I̲O̲N̲
The Back Panel type 8 is preformed to be the interface
link between the application equipment and the I/O-array
of the I/O-modules in the CTX-Crate.
Back Panel type 8 can be strapped as DTE or DCE Back
Panel.
As shown on figure 1-1, the Back Panel is mounted on
the back side of the CTX-Crate and connected to the
motherboard via a 64 wire flatcable. Protection ground
(CCITT NO. 101) can be connected by a groundwire.
Connectors for the external cable connections are four
25 pin (female) Cannon.
FIGURE 1-1 BACK PANEL TYPE 8 MOUNTED IN A CAMAC 5U CRATE.
1.1 M̲O̲D̲U̲L̲E̲ ̲S̲T̲A̲T̲U̲S̲
CPS/LST/001
Configuration Item Release Record
2̲ ̲ ̲I̲N̲T̲E̲R̲F̲A̲C̲E̲ ̲S̲P̲E̲C̲S̲.̲
2.1 I̲N̲T̲E̲R̲F̲A̲C̲E̲ ̲S̲I̲G̲N̲A̲L̲ ̲S̲P̲E̲C̲I̲F̲I̲C̲A̲T̲I̲O̲N̲S̲
Each of the four line connectors has the following
connections:
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
PIN NO. NAME JUMPER CCITT
NO.
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
1 Protection Ground 101
2 Transmitted Data X17 103
Received Data X18 104
3 Received Data X19 104
Transmitted Data X16 103
4 Request to Send X13 105
Ready for Sending X10 106
5 Ready for Sending X11 106
Request to Send X12 105
6 Data Set Ready X09 107
Data Terminal Ready X14 108
7 Signal Ground 102
8+11 Carrier Detector 104
13 Standby Indicator 117
15 Transmitter Clock X04 113/114
Receive Clock X05 115
17 Receive Clock X07 115
Transmitter Clock X06 113/114
Data Signal rate selector X01 111
19 Select Standby 116
20 Data terminal ready X15 108
Data Set Ready X08 107
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
PIN NO. NAME JUMPER CCITT
NO.
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
22 Standby Indicator 117
24 Transmit clock X03 113/114
Receive Clock X02 115
2.2 E̲L̲E̲C̲T̲R̲I̲C̲A̲L̲ ̲I̲N̲T̲E̲R̲F̲A̲C̲E̲ ̲S̲P̲E̲C̲.̲
No electrical circuits are mounted on the Back Panel
but all signal lines are according to CCITT-V24 Recommendations.
2.3 M̲E̲C̲H̲A̲N̲I̲C̲A̲L̲ ̲I̲N̲T̲E̲R̲F̲A̲C̲E̲ ̲S̲P̲E̲C̲.̲
The Back Panel type 8 consists of a PC-Board, fixed
on a metallic panel to be mounted on the rear of a
CTX-Crate (Figure 1-1).
The connector interface against the Motherboard is
a 64 pin connector. Pin is marked by an arrow and
will always be upwards. Each line communication channel
has allocated four ground wires of the 64 wire flatcable
to perform a proper signal ground. Protection Ground
taken from the power supply has to be connected to
the Back Panel via a Spade Connector.
FIGURE 2.1-1 PIN LAYOUT OF MOTHERBOARD CONNECTOR
3̲ ̲ ̲B̲L̲O̲C̲K̲E̲D̲ ̲S̲C̲H̲E̲M̲A̲T̲I̲C̲
Ref.: Dwg. No. 2-331.
Blocked Schematic
4̲ ̲ ̲P̲A̲R̲T̲S̲ ̲L̲I̲S̲T̲
Ref.: 5.39300-00.
Parts List
Parts List
5̲ ̲ ̲M̲E̲C̲H̲A̲N̲I̲C̲A̲L̲ ̲D̲R̲A̲W̲I̲N̲G̲S̲
3 - 2955 BP-8 ASSEMBLY DRAWING
3 - 2954 BP-8 ASSEMBLY DRAWING
3 - 2956 PCB ASSEMBLY DRAWING
K4 - 605 PCB ASSEMBLY DRAWING
ASSEMBLY DRAWINGS
ASSEMBLY DRAWING
ASSEMBLY DRAWING
ASSEMBLY DRAWING
6̲ ̲ ̲A̲C̲C̲E̲S̲S̲O̲R̲I̲E̲S̲
6.1 J̲U̲M̲P̲E̲R̲
Straps on the PC-Board can be made by using 2 POL.
Jumpers, such as AMP 141767-1 CR P/N 6.25500-00.
6.2 6̲4̲ ̲W̲I̲R̲E̲ ̲F̲L̲A̲T̲ ̲C̲A̲B̲L̲E̲
The connection between motherboard and Back Panel can
be made by Intern. Kable type 1 CR P/N 5.05316-10 (28
CM), or by Intern. Kable type 2 CR P/N 5.05316-11 (35
CM) depending on placement on the rear crate.
6.3 G̲r̲o̲u̲n̲d̲ ̲W̲i̲r̲e̲
Ground for the Back Panel can be taken from the Motherboard
by using Ground wire for BP-8 CR P/N 7.58101-03
Kabel, type 1
Kabel, type 2
Assembly Drawing BP-8
