top - download
⟦cf55817ed⟧ Wang Wps File
Length: 23195 (0x5a9b)
Types: Wang Wps File
Notes: Spelunked
Names: »~ORPHAN75.08«
Derivation
└─⟦17e14ee1a⟧ Bits:30006162 8" Wang WCS floppy, CR 0237A
└─ ⟦this⟧ »~ORPHAN75.08«
WangText
(…00……00……00……00…K…0a……00……00…K…0c…K…0d…K…02…K…06…J…0a…J…0f…J…02…I…08…I…0a…I…0f…I
I…07…H…0a…H…0e…H
H…05…G…0a…G…0c…B…0a…B…0c…B…01…B
A…08…A…0a…A…0f…A…01…A @…09…@…0c…<…08…<…0b…<…02…<…07…2
2…07…1…0a…1…0e…1…86…1 …02… …02… …02…
2982A/rt/237A …02…CPS/TCM/005
…02…KJA/830912…02……02…
CAMPS SITE LEVEL MAINTENANCE MANUAL
…02…Issue 1…02…CAMPS
CHANNEL UNIT TEST PROCEDURES STEP 2000-3000 (cont'd)
STEP PROCEDURE OBSERVATION/ACTION
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
2982A/rt/237A …02…CPS/TCM/005
…02…KJA/830912…02……02…
CAMPS SITE LEVEL MAINTENANCE MANUAL…02…Issue 1…02…CAMPS
4.3.3.2 C̲H̲A̲N̲N̲E̲L̲ ̲U̲n̲i̲t̲ ̲T̲e̲s̲t̲ ̲P̲r̲o̲c̲e̲d̲u̲r̲e̲s̲…86…1 …02… …02… …02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
2000 CU TEST ENTRY
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
Before start of the CUtest procedure,
verify that
1. The commands typed on the
Maint.Pos.VDU is directed
to the PU which should execute
the test.
2. The PU is offline.
3. The PU is enabled
4. The PU is in Normal Mode.
It is possible to obtain these
condtions e̲i̲t̲h̲e̲r̲
a) by commands issued from the
Maint.Pos. VDU via the WD
Subsystem.
b) by manual switchs settings
on the MAP module and a reconfiguration
procedure.
a.1) P̲U̲ ̲-̲ ̲M̲a̲i̲n̲t̲.̲P̲o̲s̲.̲V̲D̲U̲ ̲c̲o̲m̲m̲u̲n̲i̲c̲a̲t̲i̲o̲n̲
̲b̲y̲ ̲t̲h̲e̲ ̲W̲D̲ ̲C̲o̲m̲m̲a̲n̲d̲.̲
PUNno, no isNo of the actual
PU. (refer to section 5.7.6
in (*)).
a.2) P̲U̲ ̲O̲f̲f̲l̲i̲n̲e̲ ̲b̲y̲ ̲t̲h̲e̲ ̲W̲D̲ ̲c̲o̲m̲m̲a̲n̲d̲:̲
OFLI (refer to section 5.7.7
in (*))
a.3) P̲U̲ ̲e̲n̲a̲b̲l̲e̲d̲ ̲b̲y̲ ̲t̲h̲e̲ ̲W̲D̲ ̲c̲o̲m̲m̲a̲n̲d̲:̲
̲E̲N̲P̲U̲
(refer to section 5.7.4 in (*))
a.4 P̲U̲ ̲-̲ ̲n̲o̲r̲m̲a̲l̲ ̲m̲o̲d̲e̲ ̲t̲h̲e̲ ̲W̲D̲c̲o̲m̲m̲a̲n̲d̲:̲
̲N̲O̲R̲M̲
(refer to section 5.7.9 in (*))
(*) CAMPS MAINTENANCE POSITION
OPERATION MANUAL
DOC.No. CPS/OPM/005…86…1 …02…
…02… …02… …02…
b.1) P̲U̲ ̲-̲ ̲M̲a̲i̲n̲t̲.̲P̲o̲s̲.̲ ̲V̲D̲U̲ ̲c̲o̲m̲m̲u̲n̲i̲c̲a̲t̲i̲o̲n̲
̲b̲y̲ ̲r̲e̲c̲o̲n̲f̲i̲g̲u̲r̲a̲t̲i̲o̲n̲
It is possible to connect the
Maint.Pos. VDU directly to the
PU by a reconfiguration procedure.
The procedure isdescribed in
step 3600 - 3700 in section
4.3.3.3.
b.2) P̲U̲ ̲o̲f̲f̲l̲i̲n̲e̲ ̲b̲y̲ ̲s̲w̲i̲t̲c̲h̲s̲e̲t̲t̲i̲n̲g̲:̲
The PU is taken offline by presssing
the MC button situated on the
front of the MAP module in the
actual PU (refer to section
4.5).
b.3) P̲U̲ ̲e̲n̲a̲b̲l̲e̲d̲ ̲b̲y̲ ̲w̲i̲t̲c̲h̲s̲e̲t̲t̲i̲n̲g̲:̲
The PU is enabled by switching
the EN/DIS switch on the front
of the MAP module in the actual
PU to the EN position (refer
to section 4.5)
b.4) P̲U̲ ̲-̲ ̲N̲o̲r̲m̲.̲ ̲M̲o̲d̲e̲ ̲b̲y̲ ̲s̲w̲i̲t̲c̲h̲s̲e̲t̲t̲i̲n̲g̲:̲
The PU is set in normal mode
by switching he MAIN/NRM switch
on the front of the MAP module
to the NRM position. (refer
to section 4.5)
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *…86…1 …02… …02… …02… …02…
2005 Assign the FD Ctrl. o The following output should
to the offline PU appear:
by the Disk Assign-
ment Command (refer "FFFF"
to the Maint.Pos. " "
Operation anual) or
by the CUCP switch AEN
which is switched to o If correct, continue to step
the offline PU. 2010.
Enable the FD Ctrl. o If the expected output does
by typing: not appear then
it indicates that there is no
IR 1A[1 (CR) access to the FD Ctrl.
GO TO step 2015.
o If it is not possible to enter
commands on the VDU then it
indicates a possible error
in the PU subsystem, or in
the VDU - PU connection check
the Maint. Pos. VDU.
GO TO step 6000.
* * * ** * * * * * * * * * * * * * * * * * * * * *
* * * * * *
2010 Analyze the error o If
one
or
more
of
the
following
error
reports
are
printed
on
the
maintenance
position
printer
̲ ̲ ̲ ̲R̲E̲P̲-̲I̲D̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲U̲N̲I̲T̲ ̲N̲o̲
F̲M̲S̲ ̲0̲0̲1̲-̲F̲M̲S̲0̲2̲3̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲1̲ ̲o̲r̲ ̲3̲
or
there is an error indication
in the MMD drive, Disk Ctrl,
DCA.
GO TO step 2300
o If one or more of the following
error reports are printed on
the maintenance position printer.
̲ ̲ ̲ ̲R̲E̲P̲-̲I̲D̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲U̲N̲I̲T̲ ̲N̲o̲
F̲M̲S̲0̲0̲1̲-̲F̲S̲0̲2̲3̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲2̲ ̲ ̲ ̲
or
there is an error indication
in the SMD drive, Disk Ctrl,
DCA.
GO TO step 2400
o If one or more of the following
error reports are printed on
the maintenance position printer.
̲ ̲ ̲ ̲ ̲R̲E̲P̲ ̲I̲D̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲
P̲E̲R̲ ̲0̲0̲6̲ ̲-̲ ̲P̲E̲R̲ ̲0̲0̲8̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲
or
there is an error indication
in the LTU channels
GO TO step 2500
o If one or more of the following
error reports are printed on
the maintenance position.
̲ ̲ ̲ ̲ ̲R̲E̲P̲ ̲I̲D̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲ ̲
M̲S̲0̲2̲4̲ ̲-̲ ̲F̲M̲S̲0̲3̲6̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
̲ ̲ ̲
or
there is an error indication
in the FD drive, FD Ctrl, SFA.
GO TO step 2600
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2015 Open the doors to o Check
that
the
power
LEDS
are
"ON"
in
the CU Crate in the following modules:
Rack B.
- POWER Supplies
- FD Ctrl.
- CUCP
- Disk Ctrl.
- LTUs
- CIAs (rear Crate)
- DCAs (rear Crate)
- MBT (rear Crate)
If correct, continue to step
2020.
o If the power is OFF in one
or more of the modules, it
indicates a possible error
in the CU Crate or in the actual
module(s).
Replace the actual module(s)
Repeat step 2015
If the power is still OFF in
the actual module(s)
GO TO step 2800
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2020 Verification check o Verify
that
the
FD
Ctrl.
and
the
Disk.
Crtl.
No.2
is
switched
to
the
offline
PU
on
the
CUCP.
(Allow
enable
switch).
Check the cable and connectors
btween the MIA (in offline
PU crate) and the CIA.
Check the cable and connectors
between the SFA and the FD
drive.
GO TO step 2025.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *
2025 Turn the power OFF o The
following
outut
should
appear
on
and ON again on the the Maint. Pos. VDU:
FD Drive.
"FFFF"
Remove/Insert the " "
FD Ctrl. from/to
the CU Crate.
Try to enable the If correct, it indicates that
it is
FD Ctrl. by typing: now possibleto access the FD
Ctrl.
IR 1A[1 (CR) Verify the CU Subsystem.
GO TO step 2900
o If the expected output does
not appear then it indicates
that it is not possible to
enable the FD Crtl.
Remove the CUCP
Repeat step 2025
If it i now possible to enable
the FD CTRL then there is an
error in the CUCP.
Replace the CUCP
Verify the CU Subsystem
GO TO step 2900
If it is still not possible to
enable the FD Ctrl then
Remove the CCA (rear of
CU crate)
Repea step 2025
If it is still not possible to
enable the FD Ctrl then
GO TO STEP 2030
If it is now possible to enable
the FD Ctrl then there is an
error in the CCA:
Replace the CCA
Verify the CU Subsystem
GO TO step 2900
* * * * * * * * * * * * * ** * * * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
* * * * * * * * * * * * * * * * * * *
* *
*The SMD DISK CTRL is taken offline *
* *
* * * * * * * * * * ** * * * * * * *
2030 Seat the CUCP
and the CCA mo-
dules in the
CU CRATE
Assign the Disk o The
following
output
should
appear:
Ctrl. No. 2 to the
offline PU by the "FFFF"
Disk Drive Assign- " "
ment Command (refer
to the Mant.Pos.
Operation Manual) If correct, it indicates an
error in the FD ctrl.
or by the CUCP
switch which is Replace FD ctrl. (refer
to
switched to the Section 4.4)
offline PU.
GO TO step 2005.
Enable the DISK
Ctrl. No.2
by typing:
IR 1A25 (CR)
o If the expected output does
not appear then it indicates
that it also is impossible
to enable the DISK Ctrl. No.2
GO TO step 2035.
* * * * * * * * * * * * * * * * ** * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2035 Turn the power OFF o The
following
output
should
appear
on
and ON on the the Maint.pos. VDU:
SMD disk drive
"FFFF"
Remove/Insert the " "
Disk Ctrl. from/o
the CU Crate If correct, it indicates that
it is now
(Slot 18) possible to access the Disk Ctrl.
(Slot 18).
Try to enable the
Disk Ctrl. by
typing:
IR 1A25 (CR) Verify the CU Crate
GO TO step 2900
o If the expected output does
not appear then it indicates
that it is not possible to
enable the Disk Ctrl.
GO TO step 2040.
* * * * * * * * * * * * * * * ** * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2040 It is necessary to o Verify
that
the
MIA-CIA
cable
is
check the MIA-CIA properly connected to the respective
connection. modules.
Continue to step 2045.
* * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *
2045 Enable the FD Ctrl. o The
following
output
should
appear:
by typing:
"FFFF"
IR 1A[1 (CR) " "
If correct, it is now possible
to enable the FD Ctrl.
Verify the CU Crate
GO TO step 2900
o If the expected output does
not appear then it indicates
that it is not possible to
enable the FD Ctrl.
Replace CIA (refer to
Section 4.4)
Repeat step 2045.
If the error is not cleared.
Replace the MIA (efer
to Section 4.4)
Repeat step 2045.
If the error is still not cleared,
the CU Crate and modules included
should be checked.
GO TO step 2050.…86…1 …02…
…02… …02…
…02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *
2050 Remove the o The
following
output
should
appear:
FD CTRL module
"FFFF"
" "
Enable the DISK
Ctrl. #2 by typing:
IR 1A25 (CR) If correct, it indicates an
error in the removed FD CTRL
module.
Replace FD CTRL (refer to Section
4.4)
Repeat step 2050.
a)If it is possible to acess
the DISK
Ctrl. No.2, the error is cleared.
Verify the CU Crate.
GO TO Step 2900
b)If the error is still present,
it is necessary to check the
CU crate.
Check the CU crate
GO TO step 2800…86…1 …02…
…02… …02…
…02… …02…
o If the expected output does
not appear then replace the
original FD CTRL module (refer
to Section 4.4)
Remove the DISK CTRL #2 module
(refer to Section 4.4)
Continue tostep 2055.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *
2055 Enable the FD o The
following
output
should
appear:
Ctrl. by typing:
"FFFF"
" "
IR 1A[1 (CR) If correct, it indicates an
error in the removed ISK CTRL
#2 module.
Replace DISK CTRL #2 (refer
to section 4.4)
Repeat step 2055.
a)If it is possible to access
the FD, the error is cleared.
Verify the CU Crate. GO
TO
step
2900.
b)If the error is still present,
it is necesary to check the CU
crate.
Check the CU crate
GO TO step 2800.
o If the expected output does
not appear then replace the
original DISK Ctrl. #2 module
(refer to Section 4.4)
Continue to step 2060.
* * * * * * * * * * * * * * * * * * ** * * * * * *
* * * * *
2060 Assign the DISK o The
following
output
should
appear:
CTRL. #2 to the on- FFFF"
line PU. (refer to " "
the Maintenance
Position
Operation Manual) If correct, it indicates an
error in the cleared
Deasign and re- DISK CTRL. # 1 module.
move the DISK
CTRL. # 1 (slot 20) Replace DISK CTRL.
in the following way: # 1 (refer to section
4.4)
Repeat step 2060
The DISK CTRL. # 1
is deassigned from
the online PU by a)f it is possible to access
the FD
the DISK Drive CTRL, the error is cleared.
Assignment
command (refer to Verify the CU Crate
the Maint. Pos. GO TO step 2900.
Operation Manual)
b)If the error is still present,
it is necessary to checkthe CU
Crate.
Remove DISK CTRL # 1 Check the CU Crate
(refer to Section 4.4) GO TO step 2800
Enable the FD CTRL
by typing:
IR 1A[1 (CR…86…1 …02…
…02… …02… …02… …02…
o If the expected output does
not appear then replace the
original DISK CTRL. # 1 module
(refer to Section 4.4)
Continue to step 2065.
* * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2065 Assign the DISK CTRL. o The
following
output
should
appear:
#1 to the online PU
in the following way: "FFFF"
" "
a) Verify that the If correct, it inicates an
error in
CUCP switch-AEN is the cleared LTU # 1 module.
switched to the online
PU and
b) Assign the DISK CTRL Replace LTU # 1
# 1 by the DISK Drive (refer to Section 4.4).
Assignment command Repeat step 2065
(refer to the Mint.
Position Operation
Manual a) If it is possible to access
the FD
CTRL., the error is cleared.
Disable and remove Verify the CU Crate
the LTU # 1 (slot 5) GO TO step 2900.
in the followin way:
b)If the error is still present,
it
Users connected to is necessary to check the CU
Crate.
the LTU #1 must be
requested to cease Check the CU Crate.
operation. GO TO step 2800.
When all users
connected to th LTU
# 1 have ceased
operation, the LTU #1
is taken offline by
the LTU Control
(refer to the Maint.
Pos. Operation Manual)
Remove LTU # 1 (slot 5)
(refer to Section 4.4)
Assign the FD CTRL by
typing:
IR 1A[1 (CR)…86…1 …02… …02… …02… …02… …02…
o If the expected output does
not appear then replace the
LTU #1 module (refer to Section
4.4).
Continue to step 2070.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * …86…1 …02… …02… …02… …02… …02…
2070 Enable the LTU # 1 o The
following
output
should
appear:
to the online PU
in the following way: "FFFF"
" "
a)Verify that the
CUCP switch-AEN is If correct, it idicates an
error in
switched to the online the removed LTU # 2 module.
PU and
b) Enable the LTU # 1 Replace LTU # 2
by the LTU (refer to Section 4.4).
Control command Repeat step 2070
(refer to the Maint.
Pos.Operation
Manual) a)If it is possible to access
the FD
CTRL. the error is cleared.
Disable and remove Verify the CU Crate.
the LTU # 2 (slot 6) GO TO step 2900.
from the online PU in
te following way: b)If the error is still present,
it
is necessary to check the CU
Crate.
Users connected to
the LTU # 2 must be Check the CU Crate.
requested to cease
operation. GO TO step 2800.
When all users
connected to the LTU
2 have ceased
operation, the LTU # 2
is taken offline by
the LTU Control
(refer to the Maintenance
Position Operation Manual)
Remove LTU # 2 (slot 6)
(refer to Section 4.4)
Enable the FD CTRL by
typing:
IR 1A[1 CR)…86…1 …02… …02… …02… …02… …02…
o If the expected output does
not appear then replace the
LTU # 2 module (refer to Section
4.4.
Continue to step 2075.
* * * * * * * * * * * * * * * * * * * * * * * * * **
* * * * …86…1 …02… …02… …02… …02… …02…
2075 Enable the LTU # 2 o The
following
output
should
appear:
to the online PU
in the following way: "FFFF"
" "
a)Verify that the
CUCP switch-AEN is If correct, it idicates an
error in
switched to the online the cleared LTU # 3 module.
PU and
b) Enable the LTU # 2 Replace LTU # 2
by the LTU (refer to Section 4.4).
Control command Repeat step 2075
(refer to the Maint.
Pos. Operation
Manual) a)If it is possible to access
the FD
CTRL. the error is cleared.
Disable and remove Verify the CU Crate.
the LTU # 3 (slot 7) GO TO step 2900.
from the online PU in
the following way b)If the error is still present,
it
is necessary to check the CU
Crate.
Users connected to
the LTU # 3 must be Check the CU Crate.
requested to cease GO TO step 2800.
operation.
When all users
connected to the LTU
# 3 have cease
operation, the LTU # 3
is taken offline by
the LTU Control
(refer to the Maint.
Pos. Operation Manual)
Remove LTU # 3 (slot 7)
(refer to Section 4.4)
Enable the FD CTRL by
typing:
IR 1A[1 (CR)…86…1 …02… …02… …02… …02… …02…
o If the expected output does
not appear then replace the
LTU # 3 module (refer to Section
4.4.
Continue to step 2080.
* * * * * * * * * * * * * * * * * * * * * * * * * **
* * * * …86…1 …02… …02… …02… …02… …02…
2080 Enable the LTU # 3 o The
following
output
should
appear:
to the online PU
in the following way: "FFFF"
" "
a)Verify that the
CUCP switch-AEN is If correct, it idicates an
error in
switched to the online the cleared LTU # 4 module.
PU and
b) Enable the LTU # 3 Replace LTU # 4
by the LTU (refer to Section 4.4).
Control command Repeat step 2080
(refer to the Maint.
Pos. Operation
Manual) a)If it is possible to access
the FD
CTRL. the error is cleared.
Disable and remove Verify the CU Crate.
the LTU # 4 (slot 8) GO TO step 2900.
from the online PU in
the followingway: b)If the error is still present,
it
is necessary to check the CU
Crate.
Users connected to
the LTU # 4 must be Check the CU Crate.
requested to cease GO TO step 2800.
operation.
When all users
connected to the LTU
# 4 have cased
operation, the LTU # 3
is taken offline by
the LTU Control
(refer to the Maint.
Pos. Operation Manual)
Remove LTU # 4 (slot 8)
(refer to Section 4.4)
Enable the FD CTRL by
typing:
IR 1A[1 (CR)…86…1 …02… …02… …02… …02… …02…
o If the expected output does
not appear then replace the
LTU # 4 module (refer to Section
4.4.
Continue to step 2085.
* * * * * * * * * * * * * * * * * * * * * * * * * **
* * * * …86…1 …02… …02… …02… …02… …02…
2085 Enable the LTU # 4 o The
following
output
should
appear:
to the online PU
in the following way: "FFFF"
" "
a)Verify that the
CUCP switch-AEN is If correct, it idicates an
error in
switched to the online the removed LTU # 3 module.
PU and
b) Enable the LTU # 4 Replace LTU # 3
by the LTU (refer to Section 4.4).
Control command Repeatd step 2085
(refer to the Main.
Position Operation
Manual) a)If it is possible to access
the FD
CTRL. the error is cleared.
Disable and remove
the DISK CTRL # 3
(slot 16) in the Verify the CU Crate.
following way: GO O step 2900.
The DISK CTRL. # 3 b)If the error is still present,
it
is deassigned by is necessary to check the CU
Crate.
the DISK Drive Assign-
ment command Check the CU Crate.
(refer to the Maint.
Pos. OperationManual) GO TO step 2800
Remove Disk Ctrl.# 3
(slot 16)
(refer to Section 4.4)
Enable the FD CTRL by
typing:
IR 1A[1 (CR)…86…1 …02… …02… …02… …02… …02…
o If the expected output does
not appear then replace the
LTU # 3 module (refer to Section
4.4.
Continue to step 2090.
* * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * …86…1 …02… …02… …02… …02… …02…
2090 Assign the DISK CTRL. o It
is
still
impossible
to
access
the
# 3 to the online PU FD CTRL, and it is therefore
necessary
in the following way: to check the CU Crate.
)Verify that the Check the CU Crate
CUCP switch-AEN is
switched to the online GO TO step 2800
PU and
b) Assign the DISK CTRL.
# 3 by the Disk Drive
Line Control command
(refer to the Maintenance
Position Operation Manal)
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * …86…1 …02… …02… …02… …02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *
2300 ERROR IN THE ENTRY
MMD DISK DRIVE # -
DCA # ̲
DISK CTRL. # ̲
* * * * * * * * * * * * * * * * * * * * * ** * * *
* * * * *
2305 Deassign the DISK CTRL. o The
following
output
should
#
̲
appear:
in the following way:
"FFFF"
a) The DISK CTRL. # ̲ "----"
is deassigned by If correct, continue to
step 2310
the Disk Drive Assign-
ment command.
(refer to the Maint.
Pos. Operation
Manual) or
b) The CUCP
switch-AEN
is switched
to the offline PU.
Enable the DISK CTRL.
# ̲ by typing:
IR 1Axx (CR)
xx is the I/O
address of the DISK
CTRL. # ̲, i.e.
DISK DISK
CTRL # ̲
Slot xx
N̲o̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
20 1 23
1̲6̲ ̲ ̲ ̲ ̲ ̲3̲ ̲ ̲ ̲ ̲ ̲2̲6̲
o If the xpected output does
not appear then it indicates
an error in the DISK CTRL.
# ̲ module.
GO TO step 2700.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2310 Check the confi- o The
following
configuration
should
guration of the appear:
CU crate by en-
tering: See figure 4.3.3.2-1
UM1 (CR) If correct, continue to step
315.
o If the I/O address and the
RAM displacement of the DISK
Ctrl. are not correct.
Replace the Disk Ctrl.
# ̲
(Refer to sec. 4.4)
Repeat step 2305 and 2310
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *
UM1
Figure 4.3.3.2-1
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * *…86…1 …02… …02… …02… …02… …02…
2315 It is now possible to o The
following
output
should
appear:
boot the DISK test
program. "CSS/730 CR 80 M DISK FD
A detailed step-b- TEST VS.....
step procedure is "CPU ["
described in sec- "----"
tion 4.7.2.1.
If correct, continue to step
2320
Below are listed the
main steps in the
boot procedure of
the DISK test.
Before entering
the boot command,
verify that:
a) The actual DISK or FD
CTRL is assigned to
the offline PU.
b) The actual disk
pack/diskette is
mounted
in the Drive.
The FD bootcommand is
as follows:
F̲D̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
BA 1[[1(CR)
BT FD5[[(C)
BU [ or 1 (CR)
B̲E̲ ̲(̲C̲R̲)̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
The Disk boot
command is as
follows:
S̲M̲D̲ ̲D̲I̲S̲K̲
BA 1[25 (CR)
BM 14[ (CR)
B̲E̲ ̲7̲ ̲ ̲ ̲ ̲ ̲(̲C̲R̲)
