top - download
⟦e0b62187a⟧ Wang Wps File
Length: 8366 (0x20ae)
Types: Wang Wps File
Notes: Spelunked
Names: »~ORPHAN71.00«
Derivation
└─⟦17e14ee1a⟧ Bits:30006162 8" Wang WCS floppy, CR 0237A
└─ ⟦this⟧ »~ORPHAN71.00«
WangText
…00……00……00……00……00…G…02……00……00…G G…05…F…0b…F…0e…F…02…F…06…E…0a…E…0f…E…01……86…1 …02… …02… …02…
2845A/ktd/ …02…CPS/TCM/005
…02…KJA/830912…02……02…
CAMPS SITE LEVEL MAINTENANCE MANUAL
…02…Issue 1…02…CAMPS
WATCHDOG TEST PROCEDURES STEP 3000-4000 (cont'd)
STEP PROCEDURE OBSERVATION/ACTION
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
2845A/ktd/ …02…CPS/TCM/005
…02…KJA/830912…02……02…
CAMPS SITE LEVEL MAINTENANCE MANUAL
…02…Issue 1…02…CAMPS
4.3.3.3 W̲a̲t̲c̲h̲d̲o̲g̲ ̲T̲e̲s̲t̲ ̲P̲r̲o̲c̲e̲d̲u̲r̲e̲s̲
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3000 WD TEST ENTRY
The WD monitors and controls
the CAMPS H/W.
If the WD fails, it is automatically
takenout of service and the objects
controlled by the WD will remain
unchanged. The system S/W will
direct the active PU error messages
to the supervisor report printer.
It is still possible to monitor
and reconfigure the CAMPS system
by LED indicatin and switchsettings
on the modules.
If the CAMPS system is reconfigured,
it is possible to communicate
with one of the PUs. The reconfiguration
procedure is described in step
3450. The boot and start commands
are not changed if the system
is reonfigured as described in
step 3450.
If the maintenance position VDU
fails, then the WD operation
not involving the VDU and the
printer continues.
If the maintenance position printer
fails, the system S/W directs
the active PU error messages
o the supervisor report printer.
The WD continues operations not
involving the VDU subsystem at
site level.
In case of an error in the WD,
the only remedy is to order a
new WD from the depot.
The test described in this section
of the WD is reuced to a functional
test in order to decide whether
the WD is working or not.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3005 Analyze the error o If the error report is as foloows:
situation
CCBXXX
then
GO TO step 3300
o If there is an error indication
in:
Mait. Pos. VDU - WD - PU
then
GO TO step 3400
o If there is an error indication
in:
Maint. Pos. MSP - WD - PU
then
GO TO step 3500
o If there is discovered an error
in one of the
CONTROL/ASSIGN commands
or
STATUS setup in FORMAT AREA
described in the
Maintenance Position Operation
Manual Doc. No. CPS/OPM/005
then
GO TO step 3600
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *…86…1 …02… …02… …02… …02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3300 Error detected BY WD ENTRY
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3305 Analyz the error o If one of the following power
level error reports appears
CCB001
CCB005
CCB007
CCB013
CCB014
CCB016
CCB022
CCB024
then GO TO step 3310
o If one of the following switch
setting reports appears
CCB006
CCB008
CCB011 - CCB012
CCB026
then GO TO step 3315
o If one of the following digital
error reports appears:
CCB018
CCB023
CCB025
then GO TO step 3320
o If one of the following temperature
error reportsappears:
CCB003
CCB009
CCB020
then GO TO step 3330
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *…86…1 …02… …02… …02… …02… …02… …02…
3310 Check the power o If the power level is not correct
level in the actual neither on the motherboard
nor on the
crate. The actual CCA (if any) then isolate the
error
stes describing as described in crate check
procedcure.
the power level
test procedure
are listed below.
C̲r̲a̲t̲e̲ ̲ ̲ ̲ ̲S̲t̲e̲p̲
PU 1805
CU 2805
TDX 4805
̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
o If the power level is correct
on the motherbord then it indicates
an error n the WD Subsystem.
Check the cables connected
to the CCBA and the CCA/BSM-X.
Replace the CCA/BSM-X
(if necessary)
If the error still appears
then it indicates an error
in the WD.
Check the WD Crate (refer
to step 3800)
Verify the WD Subsystem
GO TO step 3900.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *…86…1 …02… …02… …02… …02… …02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3315 Check the switchs- o If the switchsettings are as
described
settings in the in the error report then no
eror is
actual crate modules. present.
The switchsset-
tings are des-
cribed in section
4.5.
o If the switchssettings are
not as described in the error
report then it indicates an
error in the WD Subsystem.
Check the cable connectors
o the CCBA and the
CCA/BSMs.
If the error is still present
then the replacement of the
following modules are necessary
in order to isolate the error.
In the PU crate:
CCA/MAP/MIA
In the CU crate:
CCA/CUCP
In theTDX crate:
BSM-X
If the error is still present
then it indicates an error
in the WD.
Check the WD (refer to
step 3800)
Verify the WD Subsystem
GO TO step 3900…86…1 …02…
…02… …02… …02…
…02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3320 Check the LEDs o If there is no LED error indication
in the TDX crate in the TDX crate
(ref. to sec.4.5 then
GO TO step 3325
o If there is error indication
then correct it or replace
the failing item (refer to
step 4300).
Verify the WD Subsystem
GO TO step 3900.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * ** *
3325 It is necessary to o If it is possible to execute
the tests
test the actual using the WD commands then
the error
TDX crate using has disappeared.
S/W commands and
not the switches Verify the WD Subsystem
on the front of
the BSM-. GO TO step 3900.
The tests consist of:
TDX-BUS and
LTUX-STATUS
(These tests are
described in
step 4300-4400)
o If it is not possible to run
the tests then isolate the
error as described in the offline
troubleshooting tree.
(rfer to step 4300)…86…1
…02… …02…
…02… …02… …02… …02…
o If it is necessary to use the
switches then it indicates
an error in the WD subsystem.
Check the cables connected
to the CCBA and the BSM-X.
Replace the BSM-X
(if necessary)
If the error indication has
not disappeared then
Check the WD
(Refer to step 3800) and
Verify the WD Subsystem
GO TO step 3900
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *…86…1 …02… …02… …02… …02… …02… …02…
3330 Check the tempera- o If correct then it indicates
an error
ture level in the in the termostat or in the
WD
actual crate. Subsystem.
The level should
be within the Check that the thermostat is
range connected and adjusted
properly.
05…0e…0…0f… - 40…0e…0…0f… Replace the thermostat
(if necessary)
If the error has not disappeared
then
Replace the BSM-X/CCA
o If the temperature is out of
rangethen
Check (and replace) the
FAN and
then
Verify the WD Subsystem
GO TO step 3900.
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *…86…1 …02… …02… …02… …02… …02… …02…
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3400 Test of the Maint. ENTRY
Pos. VDU-PU
Communication
* * * * * * * * * * * * * * * * * * * * * * * * * **
* * * * *
3405 Analyze the situ- o If one of the PUs is online
then the
ation: system is still operating.
GO TO step 3410
o If none of the PUs is online
then
GO TO step 3450
* * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
3410 Check that it is o If correct then
possible to com- GO TO step 3415
municate with
the online PU.
The command is:
PUNno (ENTER)
"no" is the number
of the online PU
(refer to
Doc.No.CPS/OPM/005)
o If it isnot possible then
GO TO step 3425
* * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * *
