DataMuseum.dk

Presents historical artifacts from the history of:

CR80 Wang WCS documentation floppies

This is an automatic "excavation" of a thematic subset of
artifacts from Datamuseum.dk's BitArchive.

See our Wiki for more about CR80 Wang WCS documentation floppies

Excavated with: AutoArchaeologist - Free & Open Source Software.


top - download

⟦fed950dd0⟧ Wang Wps File

    Length: 109712 (0x1ac90)
    Types: Wang Wps File
    Notes: CPS/TPR/044               
    Names: »4544A «

Derivation

└─⟦3b1a2164c⟧ Bits:30006188 8" Wang WCS floppy, CR 0428A
    └─ ⟦this⟧ »4544A « 

WangText



4…08…4…09…4…0e…4
3…08…3…0e…3…0f…3
3…06…2…0b…2…0f…2
2…07…1…0b…1…00…1…05…0…0a…0…0f…0
/…08…/…0c…/…01…/…06….…0a….…0d….…02….…07…-…0c…-…01…-…06…,…0b…,…0f…,…02…,…07…+…0c…+…01…+…06…*…0c…*…00…*…05…)…09…)…0e…)
)…06…(…0b…(…00……86…1 
      
      
      
      
      
      
      
  …02…    
      
 …02…   …02…  
      

…02…CPS/TPR/044

…02…FS[/840125…02……02…
FACTORY
 ACCEPTANCE
 TEST SPECIFICATION
AND PROCEDURES,
 SITE 7…02……02…CAMPS








3.2.3.2  T̲e̲s̲t̲ ̲P̲r̲o̲c̲e̲d̲u̲r̲e̲ ̲2̲

         This testprocedure serves to verify functional capabilities
         of PU#2, the associated part of the CU and the connected
         TDX#2 system as identified in the VCRI. 



3.2.3.2.1    T̲e̲s̲t̲ ̲S̲e̲t̲ ̲U̲p̲

         The test is performed via an Operator Console (OC)
         which is a printer and keyboard.

         The OC is connected to the system as follows:

             1.  Substitute the leftmost OPTO transceiver in
                 the rack C Adapter crate with a V24/V28(L/L)
                 adapter (1 channel), and connect the OC to
                 the V24 connector on the front panel of the
                 adaptor.

             2.  Remove the two V24 cables from J2 and J3 located
                 on the front panel of the WCA (rear crate of
                 the Watchdog Processor crate).

             3.  Connect the two V24 cables.

         The OC is now connected to the V24 port on the MIA
         in the rear crate of PU#2 (ref. fig. 3.2.3.2.1-1).

         Carry out/control the following:

         a)  OC Set up:

             The communication part of the OC is set to:

             1)  Asynchronous communication
             2)  7 bit character length
             3)  Even parity check/generation
             4)  1 stop bit
             5)  1200 Baud communication speed
















































                    FIGURE 3.2.3.2.1-1

            C̲o̲n̲n̲e̲c̲t̲i̲o̲n̲ ̲o̲f̲ ̲t̲h̲e̲ ̲O̲p̲e̲r̲a̲t̲o̲r̲ ̲C̲o̲n̲s̲o̲l̲e̲


         b)  Switch settings in PU#1 and PU#2 front crate modules:

             1)  The NRM/MAIN switch on the MAP module front
                 panel is set to NRM.

             2)  The EN/DIS switch on the MAP module front panel
                 is set to EN.

             3)  The host number switch (S1) on the PU#2 STI
                 is set to #01 as follows:

                 S1,4 : CLOSED
                 S1,3 : CLOSED
                 S1,2 : CLOSED
                 S1,1 : OPEN

         c)  Switch settings in PU#1 and PU#2 rear crate modules:

             1)  The Baudrate select switches 1-4 (S1) on the
                 MAP Interface Adapter (MIA) Printed Circuit
                 Board (PCB) is set to #7 which corresponds
                 to a transmission speed of 1200 Baud:

                 Switch 1:  OPEN
                 Switch 2:  OPEN
                 Switch 3:  OPEN
                 Switch 4:  CLOSE

             2)  The RESET switch on the Configuration Control
                 Adaptor (CCA) front panel is set to RESET.

         d)  Switch settings in CU front crate modules:

             1)  Switches on the Channel Unit Control Panel
                 (CUCP) front panel is set as:

                 a)  The CU Bus A Switch DIS/AUTO is set to
                     AUTO

                 b)  The CU Bus B switch DIS/AUTO is set to
                     AUTO

                 c)  The Disk Ctrl. No. 1 switch AAEN/AUTO/BAEN
                     is set to AUTO



                 d)  The Disk Ctrl. No. 2 switch AAEN/AUTO/BAEN
                     is set to AUTO

                 e)  The Disk Ctrl. No. 3 switch AAEN/AUTO/BAEN
                     is set to AUTO

                 f)  The LTU No. 1 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 g)  The LTU No. 2 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 h)  The LTU No. 3 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 i)  The LTU No. 4 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 k)  The LTU No. 5 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 l)  The SD.FD.CTRL switch AAEN/AUTO/BAEN is
                     set to AUTO

         e)  Switch settings in CU rear crate modules:

             1)  The RESET switch on the CCA module front panel
                 is set to RESET

         f)  Switch settings in TU modules

             1)  All BSM-Xs:

                 a)  The AUTO/MAN/OFF switch is set to MAN

                 b)  The BUS 1/Bus 2 switch is set to BUS 2.

             2)  All LTUX-Ss:

                 a)  The CH 1 switch ON/OFF is set to ON

                 b)  The CH 2 switch ON/OFF is set to ON

                 c)  The CH 3 switch ON/OFF is set to ON

                 d)  The CH 4 switch ON/OFF is set to ON

         g)  Switch settings on frequency stabilizer rack:



             1)  The input power switch on all three stabilizers
                 are set to off.

             2)  The three rotary switches on the By-Pass panel
                 are all set to the Frequency Stabilizer position.

         h)  Setting of power switches in Computer racks:

             1)  Power switch (2) on each Mains switch is set
                 to OFF.

             2)  Power switch (2) on the Disk Drive rear panel
                 is set to "ON"

             3)  Power switch (1) on the Floppy Disk Drive rear
                 panel is set to "ON".

             4)  Power switch (1) on the Watchdog Processor
                 Unit rear panel is set to "OFF".

             5)  Power switch (2) in the rear crate of PU#1
                 is set to "ON"

             6)  Power switch (2) in the rear crate of the CU
                 is set to "ON"

             7)  Power switch (2) in the rear crate of the PU#2
                 is set to "ON".

             8)  Power switch (2) in the rear panel of each
                 80D fan unit is set to "ON".

             9)  Power switch (2) in the rear crate of the Adaptor
                 Crate is set to "ON"

             10) Power switch (1) in the rear panel of the 80S
                 Blower Unit is set to "ON"

             11) Power switch (1) on each CR80D Power supply
                 (6 front crate mounted modules) is set to "ON".

         i)  Setting of Power Switche in Line Termination racks:

             1)  Power Switch (2) on each Mains Switch is set
                 to "OFF".



             2)  Power Switch (1) on the rear panel of each
                 80S Blower Unit is set to "ON".

             3)  Power Switch (2) in the rear crate of each
                 TU is set to "ON".

             4)  Power Switch (1) on each CR80S Power Supply
                 (1 in the front crate of each TU) is set to
                 "ON".

         k)  PU#2 cable interchanges

         Interchange the TIA#1 (rear crate, slot 15) TDX connection
         and the TIA#2 (rear crate, slot 16) TDX connection.



3.2.3.2.2    T̲e̲s̲t̲ ̲I̲n̲i̲t̲i̲a̲l̲i̲z̲a̲t̲i̲o̲n̲

         The testengineers and testwitnesses are in the testroom
         and ready to perform and supervise the test.

         Power Up the System as follows 

         a)  Power Up all connected terminals i.e. VDUs, MSPs,
             OC, PTP/PTR, OCR as applicable.

         b)  The input Power Switch on the front panel of each
             Frequency Stabilizer is set to "ON".

         c)  The power switch (2) on Mains switch no. 1 is set
             to "ON" wait 15 secs.

         d)  The power switch (2) on each of the remaining Mains
             Switches is set to "ON".

         e)  Mount a Disk Pack with the test software in Disk
             Drive no. 2, close the lid and push the drive back
             in rack B. Activate the WRITE PROTECT pushbutton.

         f)  Activate "START" push button on Disk Drive No.
             2 and wait until the "READY" indicator stays "ON".

         g)  Insert a scratch Floppy Disk in each of the two
             drives in the Floppy Disk drive of rack B, and
             close the lids.



3.2.3.2.3    T̲e̲s̲t̲ ̲S̲t̲e̲p̲s̲

         The teststeps for testgroup no. 2, testprocedure no.
         2 (2/2), are given in the following preceded by a testoverview.




T̲E̲S̲T̲ ̲O̲V̲E̲R̲V̲I̲E̲W̲                                  T̲E̲S̲T̲ ̲N̲O̲.̲:̲ ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲C̲a̲p̲a̲b̲i̲l̲i̲t̲i̲e̲s̲                                 
    

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

Test Case/
Reference        Action                        SRS Reference
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

1.               CPU test                      N/A

2.               MAP test                      N/A

3.               RAM test                      N/A

4.               Disk/Floppy Disk              N/A
                 test

5.1              LTU #1                        N/A

5.2              LTU #2                        N/A

5.4              LTU #3                        N/A

6.               Load Test                     N/A

7.2              LTUX-S Link 11x-21x           N/A

7.3              LTUX-S Link 12x-22x           N/A

7.4              LTUX-S Link 13x               N/A

7.5              LTUX-S Link 14x               N/A

7.6              LTUX-S Link 24x               N/A

7.7              LTUX-S Link 15x               N/A

7.9              LTUX-S Link 25x               N/A

7.10             LTUX-S Link 1Bx               N/A


                                            /Continued....…86…1        
         …02…                             …02…                     

T̲E̲S̲T̲ ̲O̲V̲E̲R̲V̲I̲E̲W̲                                  T̲E̲S̲T̲ ̲N̲O̲.̲:̲ ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲C̲a̲p̲a̲b̲i̲l̲i̲t̲i̲e̲s̲  (Continued)                    
    

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

Test Case/
Reference        Action                        SRS Reference
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

7.12             LTUX-S Link 2Bx               N/A

7.14             LTUX-S Link 231               N/A

7.15             LTUX-S Link 171               N/A

7.16             LTUX-S Link 254               N/A

7.18             LTUX-S Teletype Test          N/A

All              Power line filtering          sec. 3.4.5.1.o

All              CPU instruction set           sec. 3.4.5.7.a.4

All              Hardware addressing           sec. 3.4.5.7.a.7




T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

1.1      OC          Examine printout on OC    Refer to Appendix
                                               B sec. 1.1

1.2      OC          Boot the CPU test pro-
                     gram as follows:

                     Enter from the OC:
                     BA 1025(CR)
                     BM 140(CR)
                     BO 621(CR)                Refer to Appendix
                                               B sec. 1.2

1.3      OC          Enter from the OC
                     REPORTLEVEL = 0(CR)
                     ACTIVATE CPU 0(CR)
                     ACTIVATE CPU 1(CR)
                     ACTIVATE CPU 2(CR)
                     TEST CPU 0 1 2(CR)        Refer to Appendix
                                               B section 1.3.

1.4      OC          Quit the CPU test by en-
                     tering from the OC:
                     QUIT(CR)                  Refer to Appendix
                                               B section 1.4




 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

2.1      OC          Boot the MAP test pro-
                     gram as follows:

                     Enter from the OC:
                     BA 1025(CR)
                     BM 140(CR)
                     BO 61F(CR)                Refer to Appendix
                                               B sec. 2.1

2.2      OC          Enter from the OC:

                     REPORTLEVEL = 0(CR)
                     TEST ALL(CR)              Refer to Appendix
                                               B section 2.2

2.3      OC          Quit the MAP test by en-
                     tering from the OC:
                     QUIT(CR)                  Refer to Appendix
                                               B section 1.4









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.1      OC          Boot the RAM test pro-
                     gram as follows:

                     Enter from the OC:
                     BA 1025(CR)
                     BM 140(CR)
                     BO 620(CR)                Refer to Appendix
                                               B sec. 3.1

3.2      OC          Enter from the OC:

                     REPORTLEVEL = 0(CR)
                     TEST ALL(CR)              Refer to Appendix
                                               B section 3.2

3.3      OC          Quit the RAM test by en-
                     tering from the OC:
                     QUIT(CR)                  Refer to Appendix
                                               B section 3.3









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.4      OC          Enter from the OC:
                     IR 1A23(CR)
                     IR 1A25(CR)
                     IR 1A26(CR)
                     IR 1A07(CR)
                     IR 1A08(CR)
                     IR 1A0B(CR)
                                               Refer to Appendix
                                               B 
                                               section 3.4

3.5      OC          Enter from the OC:
                     ZP(CR)                    Either:
                                               ZP
                                               Or:
                                               ZP
                                               Parity error(s)
                                               X












 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.6      OC          Enter from the OC:
                     ZP1(CR)                   Either:
                                               ZP1
                                               Or:
                                               ZP1
                                               Parity error(s)
                                               X
3.7      OC          Enter from the OC:
                     IR 1823(CR)
                     IR 1825(CR)
                     IR 1826(CR)
                     IR 1807(CR)
                     IR 1808(CR)
                     IR 180B(CR)
                                               Refer to Appendix
                                               B 
                                               section 3.5

                     The steps from 3.4
                     to 3.7 incl. have reset
                     possible parity errors
                     in the CU memories








 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

4.1      OC          Boot the Disk test-
                     program as follows:
                     Enter from the OC:
                     BA 1025(CR)
                     BM 140(CR)
                     BO 634(CR)                Refer to Appendix
                                               B 
                                               sec. 4.1

4.2      N/A         Depress the "START"       N/A.
                     pushbutton on disk
                     drive #2 and wait un-
                     til the "START"and
                     "READY" indicators are
                     "OFF". Replace the test
                     software disk pack in
                     Disk Drive # 2 with a
                     scratch disk pack.
                     Push the drive back
                     into rack B.
                     Activate the "START"
                     pushbutton on Drive #2
                     and wait until the
                     "READY"indicator stays
                     "ON". Depress the
                     WRITE PROTECT push-
                     button. (WRITE PROTECT
                     indicator "OFF")


 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

4.3      OC          Activate the Disk test
                     as follows:

                     Enter from the OC:        Refer to Appendix
                                               B 
                     DO TEST                   sec. 4.2
                     (Appendix A, sec. 2.1)

4.4      OC          Quit the Disk test
                     by entering from the OC:  Refer to Appendix
                                               B 
                     QUIT(CR)                  sec. 1.4

4.5      N/A         Depress the "START"       N/A.
                     pushbutton on disk
                     drive #2 and wait un-
                     til the "START"and
                     "READY" indicators are
                     "OFF". Replace the
                     scratch disk pack in
                     Disk Drive # 2 with the
                     test software disk pack.
                     Push the drive back
                     into rack B.
                     Activate the "START"
                     pushbutton on Drive #2
                     and wait until the
                     "READY"indicator stays
                     "ON". Activate the WRITE
                     PROTECT pushbutton.
                     (WRITE PROTECT indicator '"ON")
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.1.1    OC          Boot the LTU test-
                     program as follows:
                     Enter from the OC:
                     BA 1025(CR)
                     BM 140(CR)                Refer to Appendix
                                               B 
                     BO 635(CR)                sec. 5.1

5.1.2    N/A         Connect the TEST VDU      N/A
                     to J30 in the V24 fil-
                     ter box via testcable A.

5.1.3    OC          Activate the LTU#1
                     channel 1 test as follows:

                     Enter from the OC:        Refer to Appendix
                                               B 
                     DO LTU11(CR)              sec. 5.2
                     (Appendix A, sec. 3.1)

5.2.1    N/A         Connect the TEST VDU      N/A
                     to J31 in the V24 fil-
                     ter box via testcable A.

5.2.2    OC          Activate the LTU#2
                     channel 1 test as follows:

                     Enter from the OC:        Refer to Appendix
                                               B 
                     DO LTU21(CR)              sec. 5.3
                     (Appendix A, sec. 3.2)
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.2.3    OC          Quit the LTU test by en-  Refer to Appendix
                                               B
                     tering from the OC:       sec. 1.4
                     QUIT(CR)

5.3      OC          Boot the sync LTU test    Refer to Appendix
                                               B
                     as follows:               sec. 5.4
                     BA 1025(CR)
                     BM 140(CR)
                     BO 636(CR)

5.4.1    N/A         Connect testconfigu-      N/A
                     ration 1 to J26 in the 
                     V24 filter box via
                     testcable E.
                     The possible testcon-
                     figurations are described
                     in sec. 3.2.1.b2

5.4.2    OC          Activate the LTU#3
                     channel 1 test as follows:

                     Enter from the OC:        Refer to Appendix
                                               B 
                     DO LTU31(CR)              sec. 5.5
                     (Appendix A, sec. 3.3)




 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.4.3    N/A         Remove the loop back      Refer to Appendix
                                               B
                     connector on the re-      sec. 5.6
                     mote site digital patch
                     panel. Repeat step 5.4.2.
                     (The test never enters
                     the compare mode).

5.4.4    OC          Activate the 'BREAK'      Refer to Appendix
                                               B
                     key and enter:            sec. 5.7
                     LTU.SHUTDOWN(#100B)(CR)

5.4.5    N/A         Reinsert the loop back    Refer to Appendix
                                               B
                     plug and repeat step      sec. 5.5
                     5.4.2.














 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.4.6    N/A         Connect testconfigu-      N/A
                     ration 1 to J27 in the 
                     V24 filter box via
                     testcable E.
                     The possible testcon-
                     figurations are described
                     in sec. 3.2.1.b2

5.4.7    OC          Activate the LTU#3
                     channel 2 test as follows:

                     Enter from the OC:        Refer to Appendix
                                               B 
                     DO LTU32(CR)              sec. 5.8
                     (Appendix A, sec. 3.4)

5.4.8    N/A         Remove the loop back      Refer to Appendix
                                               B
                     connector on the re-      sec. 5.9
                     mote site digital patch
                     panel. Repeat step 5.4.7.
                     (The test never enters
                     the compare mode).







 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.4.9    OC          Activate the 'BREAK'      Refer to Appendix
                                               B
                     key and enter:            sec. 5.10
                     LTU.SHUTDOWN(#100B)(CR)

5.4.10   N/A         Reinsert the loop back    Refer to Appendix
                                               B
                     plug and repeat step      sec. 5.8
                     5.4.7.

5.4.11   N/A         Remove the test config-
                     uration from J27 in the
                     V24 filter box            N/A

5.5      OC          Quit the sync LTU         Refer to Appendix
                     test by entering from     B sec. 1.4
                     the OC: QUIT (CR)















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.1      N/A         Connect a TEST VDU        N/A
                     via testcable A to
                     J30 (LTU#11) in the
                     filter box. VDU set-up:
                        9600 Baud
                        Echo Mode
6.2      N/A         Power down PU#1 and add   N/A
                     1 extra memory module 
                     in PU#1 pos.15.
                     Switch setting on RAM 
                     module corresponding to 
                     no.3 RAM. Power up PU#1.
6.3      N/A         Swop Disk Controllers in  N/A
                     CU pos. 18 and 20
6.4                  Push the Master Clear     Refer to Appendix
                                               B sec. 1.1
6.4.1                Depress the WRITE PROTECT
                     push button on Drive#2
                     (WRITE PROTECT indicator
                     is 'OFF')
6.5      OC          Enter from the OC:        OC print out:
                     IR1A23 (CR)               IR1A23
                                               FFFF
                     ZP                         ZP
                                               Parity error(s)
                                               X
                     ZP1                        ZP1
                                               Parity error(s)
                                               X

6.6      OC          BO 610                    Refer to Appendix
                                               B sec. 6.1
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.7      OC          Enter time and date       Refer to Appendix
                                               B sec. 6.2

6.8      OC          Enter from the OC
                     OPEN SYS                  Refer to Appendix
                                               B 
                     DO CONFIG1                sec. 6.3

6.9      OC          Enter from the OC:
                     PRINTER ̲TASK L: Y
                     P: % ̲TMS*TERM0(CR)        Refer to Appendix
                                               B sec 6.4

6.10     OC          Enter from the OC:
                     PRINT PRI                 Refer to Appendix
                                               B sec. 6.5

6.11     OC          Enter from the OC:
                     DO HCLF20                 Refer to Appendix
                                               B sec. 6.6

6.12     OC          To terminate the
                     test enter
                     from the OC:
                     KILL SYS00(CR).
                     If not terminated the     Refer to Appendix
                                               B
                     test runs app. 1/2 hour.  sec. 6.7


 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.13     OC          To terminate the
                     system s/w enter          Refer to Appendix
                                               B
                     from the OC:              sec. 6.8
                     CLOSE(CR)

6.14     N/A         Activate Master Clear     Refer to Appendix
                                               B Sec. 1.1

6.15     N/A         Swop the Disk Control-    N/A                     lers
                                                                       in
                                                                       CU
                                                                       pos.18
                                                                       and
                     20.

6.16     OC          Enter from the OC         OC print out
                     IR1A25                    IR1A25
                                               FFFF
                     ZP1                        ZP1
                                               Parity error(s)
                                               X











 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.17     N/A         Activate the              N/A
                     WRITE PROTECT push-
                     button on Drive#2.
                     (WRITE PROTECT indica-
                     tor is 'ON')

6.18     N/A         Activate Master Clear.    Refer to Appendix
                                               B sec. 1.1




















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.1      OC          Boot the TDX1 test pro-
                     gram as follows:
                     BA 1025(CR)
                     BM 140(CR)                Refer to Appendix
                                               B 
                     BO 62F(CR)                sec 7.1

7.2      OC          Activate the link 11x-21x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:
                     DO OPEN1(CR)
                     (Appendix A, sec. 4.7a)
                     DO VDU8(CR)
                     (Appendix A, sec. 4.1)    OC print out
                                               as
                     DO CLOSE1(CR)             specified in
                                               appen-
                     (Appendix A, sec. 4.7b)   dix B, sec. 7.2

7.3      OC          Activate the link 12x-22x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:
                     DO OPEN2(CR)
                     (Appendix A, sec. 4.8a)
                     DO VDU8(CR)
                     (Appendix A, sec. 4.1)    OC print out
                                               as
                     DO CLOSE2(CR)             specified in
                                               appen-
                     (Appendix A, sec. 4.8b)   dix B, sec. 7.3
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.4.1    N/A         Power down TU#3           N/A
                     Conect 3 Test VDUs
                     via testcable A as
                     follows:
                     1 VDU to J32 in CRT
                     site B filter box.
                     1 VDU to J28 and J32
                     in CRT site A filter
                     box. (V24/V28 I/F)
                     Test VDU set up:
                        2400 Baud
                        Even parity check/
                           generation
                        1 stopbit
                        7 bits/character.
                     Power up TU#3.

7.4.2    OC          Activate the link 13x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:
                     DO OPEN13(CR)
                     (Appendix A, sec. 4.9a)
                     DO VDU4(CR)
                     (Appendix A, sec. 4.2)    OC print out
                                               as
                     DO CLOSE13(CR)            specified in
                                               Appen-
                     (Appendix A, sec. 4.9b)   dix B, sec. 7.4
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.5.1    N/A         Power down TU#4           N/A
                     Connect a Test MSP via
                     testcable C to J31 in CRT
                     site B filter box.
                     Test MSP set up:
                        2400 Baud
                        Even parity check
                        7 bits/character.
                     Power up TU#4

7.5.2    OC          Activate the link 14x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:
                     DO OPEN14(CR)             MSP 14X print
                                               out
                     (Appendix A, sec. 4.12a)  as specified
                                               in ap-
                     DO MSP (CR)               pendix B, sec.8.1
                     (Appendix A, sec.4.2)     
                     DO CLOSE14(CR)            OC print out
                                               as
                     (Appendix A, sec. 4.12b)  specified in
                                               Appen-
                                               dix B, sec. 7.5






 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.6.1    OC          Activate the link 24x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:
                     DO OPEN24(CR)             MSP24X print
                                               out as
                     (Appendix A, sec. 4.13a)  specified in
                                               appen-
                     DO MSP (CR)               dix B, sec. 8.1
                     (Appendix A, sec. 4.2)    
                     DO CLOSE24(CR)            OC print out
                                               as
                     (Appendix A, sec. 4.13b)  specified in
                                               Appen-
                                               dix B, sec. 7.6

7.6.2    N/A         Power down TU#4           N/A
                     Remove the Test MSP
                     from J31 in CRT site B
                     filter box
                     Power up TU#4

                     Quit the test program
                     by entering from the
                     OC: QUIT(CR)              Refer to Appendix
                                               A sec. 1.4
7.7                  Boot the TDX2 test 
                     program as follows:
                     BA 1025 (CR)
                     BM 140 (CR)               Refer to Appendix
                                               B
                     BO 630                    sec. 7.7
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.8.1    N/A         Power down TU#5           N/A
                     Connect the 4 test VDUs
                     to J1-4 in the V24 fil-
                     ter box.
                     Power up TU#5

7.8.2    OC          Activate the link 15x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:        OC print out
                                               as
                     DO OPEN15(CR)             specified in
                                               appen-
                     (Appendix A, sec.4.14a)   dix B sec. 7.8
                     DO VDU4 (CR)              
                     (Appendix A, sec.4.3)     
                     DO CLOSE15(CR)            
                     (Appendix A, sec.4.14b)   

7.9.1    N/A         Power down TU#5           N/A
                     Disconnect W201 from
                     ch. 1 on the V24 L/L
                     pos. A6 and connect it
                     to ch. 2 on V24 L/L in
                     pos. A13. 




 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.9.1    N/A         Disconnect W202 from      N/A
cont.                ch. 2 on the V24 L/L
                     pos. A6 and connect it
                     to ch. 3 on V24 L/L in
                     pos. A13. 
                     Connect the 4 test VDUs
                     to J1,J2,J5 and via test-
                     cable A to J25 in the V24
                     filter box.
                     Test VDU set up:
                        2400 Baud
                        Even parity check/
                           generation
                        7 Bits/character.
                     Power up TU#5.

7.9.2    OC          Activate the link 25x
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:        OC print out
                                               as
                     DO OPEN25(CR)             specified in
                                               appen-
                     (Appendix A, sec. 4.15a)  dix B sec. 7.9
                     DO VDU4 (CR)
                     (Appendix A, sec. 4.3)    
                     DO CLOSE25(CR)            
                     (Appendix A, sec. 4.15b)  

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR




T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.9.3    N/A         Power down TU#5           N/A
                     Disconnect W201 from
                     ch. 2 on the V24 L/L
                     pos. A13 and connect it
                     to ch. 1 on V24 L/L in
                     pos. A6. 
                     Disconnect W202 from
                     ch. 3 on the V24 L/L
                     pos. A13 and connect it
                     to ch. 2 on V24 L/L in
                     pos. A6. 
                     Remove the 4 test VDUs
                     Power up TU#5















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:



                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR




T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.9.4    OC          Quit the TDX2 test by
                     entering from the OC:     Refer to Appendix
                                               B
                     QUIT(CR)                  sec. 1.4























 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.10.1   OC          Boot the TDX3 test as
                     follows:
                     BA 1025(CR)
                     BM 140(CR)                Refer to Appendix
                                               B
                     BO 631(CR)                sec. 7.10

7.10.2   N/A         Power down the main and   N/A
                     remote site stat. mux.
                     Remove the testcable be-
                     tween the main site fil-
                     terbox J33 and the remo-
                     te site filterbox J40.
                     On the main site and the
                     remote site stat. mux.
                     set S1 and S2 on the ba-
                     se board switch group 2
                     to the CLOSED position
                     (extern clock). Power up
                     the main and remote site
                     stat. mux.

7.10.3   N/A         Connect the CRYPTO/MODEM  N/A
                     link between main site
                     filterbox J33 and remo-
                     te site filterbox J40.



  ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.10.4   N/A         Power up both MODEMs and  N/A
                     CRYPTOs. If identical
                     keystores on both CRYPTOs
                     are on then proceed from
                     7.18.5 else load the
                     cryptokey into keystore 1
                     on both cryptos.

7.10.5   N/A         CRYPTO synchronization    CRYPTOs are
                     should be initiated. If   synchronized
                     not CH1.ERR on the
                     RESYNC MODULE is on.
                     Activate the RESET push-
                     button on the RESYNC MO-
                     DULE.

7.10.6   N/A         Set switch S1 on the      RTS on the main
                     MODEM link to OFF         site modem goes
                                               off
                     (MODEM link open circuit) for 1.5 secs
                                               and then on again
                                               for 3 secs.

                     When RTS on the main site CRYPTOS synchronize.
                     goes off the second time
                     set switch S1 to ON.




  ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.10.7   N/A         Set switch S1 to OFF      After 13.5 secs.
                                               the CH1.ERR indicator
                                               goes on

                     Set switch S1 to ON       No synchronization
                                               is initiated

7.10.8   N/A         Activate the RESET push-  After 1.5secs
                                               the
                     button on the RESYNC      CRYPTOS synchronize.
                     MODULE

7.10.9   N/A         Set switch S2 on the      RTS on the main
                     MODEM link to OFF         site modem goes
                                               off
                     (MODEM link open circuit) for 1.5 secs
                                               and then on again
                                               for 3 secs.

                     When RTS on the main site CRYPTOS synchronize.
                     goes off the second time
                     set switch S2 to ON.

7.10.10  N/A         Set switch S2 to OFF      After 13.5 secs.
                                               the CH1.ERR indicator
                                               goes on

                     Set switch S2 to ON       No synchronization
                                               is initiated


 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.10.11  N/A         Activate the RESET push-  After 1.5secs
                                               the
                     button on the RESYNC      CRYPTOS synchronize.
                     MODULE

7.11.1   N/A         Power down TU#11.         N/A
                     Conect 2 test VDUs
                     to J28 and J32 in
                     the CRT V24 filter
                     box. Power up TU#11.

7.11.2   OC          Activate the link 1BX
                     LTUX-S test as fol-
                     lows:

                     Enter from the OC:
                     DO OPEN1B(CR)
                     (Appendix A,sec. 4.24a)
                     DO VDU4(CR)
                     (Appendix A, sec.4.2)

                     When a couple of lines    Output stops.
                     have been transmitted to
                     the remote VDUs set switch
                     S1 to OFF.




 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.11.3   N/A         When the CH1.ERR. indica- CRYPTOs synchronize
                     tor goes on set S1 to ON  and output is
                                               resumed.
                     and activate the RESET    OC print out
                                               as speci-
                     pushbutton on the RESYNC  fied in appendix
                                               B,
                     module. Let the testse-   sec. 7.11
                     quence finish normally

7.11.4   OC          Enter from the OC:
                     DO VDU4(CR)
                     (Appendix A, sec.4.2)

                     When a couple of lines    Output stops.
                     have been transmitted to
                     the remote VDUs set switch
                     S2 to OFF.

7.11.5   N/A         When the CH1.ERR. indica- CRYPTOs synchronize
                     tor goes on set S2 to ON  and output is
                                               resumed.
                     and activate the RESET    OC print out
                                               as speci-
                     pushbutton on the RESYNC  fied in appendix
                                               B,
                     module. Let the testse-   sec. 7.11
                     quence finish normally

                     Enter from the OC:
                     DO CLOSE1B (CR)
                     (Appendix A, sec.4.24b)


 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.11.6   N/A         Power down the CRYPTOs,   N/A
                     the MODEMs and the main
                     and remote site stat.
                     mux. Remove the CRYPTO/
                     MODEM link. Connect the
                     testcable between J33 in
                     the main site filterbox
                     and J40 in the remote site
                     filterbox.
                     On the main site and the
                     remote site stat. mux.
                     set S1 on the ba-
                     se board switch group 2
                     to the OPEN position
                     (intern clock). Power up
                     the main and remote site
                     stat. mux.











 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.12.1   OC          Activate the link 2BX
                     LTUX-S test as follows:

                     Enter from the OC:
                     DO OPEN 2B(CR)            MSP2BX print
                                               out as
                     (Appendix A,sec. 4.25a)   specified in
                                               appen-
                     DO MSP(CR)                dix B sec. 8.1.
                     (Appendix A, sec.4.3)     OC print out
                                               as 
                     DO CLOSE 2B (CR)          specified in
                                               appen-
                     (Appendix A, sec.4.25b)   dix B, sec. 7.12

7.12.2   N/A         Power down TU#B           N/A
                     Power down CRT site B
                     Adaptor crate and remove
                     the Test VDU and Test
                     MSP.
                     Power up the adaptor
                     crate.
                     Power up TU#B.









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.12.3   OC          Quit the TDX3 test by
                     entering from the OC:     Refer to Appendix
                                               B 
                     QUIT(CR)                  sec. 1.4

7.13     OC          Boot the TDX4 test as
                     follows:
                     BA 1025(CR)
                     BM 140(CR)                Refer to Appendix
                                               B
                     BO 632(CR)                sec. 7.13



















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.14.1               Power down TU#3           N/A
                     Connect the test VDU to 
                     J32 via testcable A.
                     Test VDU set up:
                        2400 Baud
                        even parity check/generation
                        1 stop bit
                        7 bit character length
                      Power up TU#3

7.14.2   OC          Activate the Link 231
                     LTUX-S test as follows:
                     
                     Enter from the OC:
                     DO OPEN 231(CR)
                     (Appendix A, sec.4.30a)
                     DO OCR(CR)
                     (Appendix A, sec.4.5)     OC print out
                                               as
                     DO CLOSE 231(CR)          specified in
                                               appen-
                     (Appendix A, sec.4.30b)   dix B, sec.7.14








 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.15.1   N/A         Power down TU#7. Power    N/A
                     down the adaptor crate
                     in CRT site A and connect
                     a Test VDU to J27 in the
                     CRT site A filter box via
                     testcable A.
                     Test VDU set up:
                        2400 Baud
                        Even parity check/
                           generation
                        7 Bits/character
                     Power up the adaptor
                     crate. Power up TU#7.

7.15.2   OC          Activate the link 171     
                     test as follows:
                     Enter from the OC:
                     DO OPEN171(CR)
                     (Appendix A,sec. 4.33a)
                     DO OCR
                     (Appendix A, sec. 4.5)    OC print out
                                               as
                     DO CLOSE171(CR)           specified in
                                               appen-
                     (Appendix A, sec. 4.33b)  dix B, sec. 7.15





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.15.3               Power down TU#7. Power
                     down the adaptor crate
                     in CRT site A. Remove
                     the Test VDU.
                     Power up the adaptor
                     crate. Power up TU#7.






















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.16.1   N/A         Power down TU#5.          N/A
                     Connect the PTP/R to
                     J25 in the V24 fil-
                     ter box. Set switch S2
                     on LTUX-S #25 to:
                     1: Closed
                     2: Closed
                     3: Open
                     4: Closed
                     Power up TU#5.

7.16.2   OC          Activate the link 254
                     LTUX-S test as follows:

                     Enter from the OC:
                     DO OPEN254(CR)
                     (Appendix A, sec.4.31a)
                     DO PTP(CR)                A piece of tape
                                               is
                     (Appendix A, sec.4.4a)    punched. Tear
                                               it off and feed
                                               it into the 
                                               reader with the
                                               reader switch
                                               load/run in position
                                               load.




 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR


T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.16.2   OC          Enter from the OC:
cont.
                     DO PTR(CR)                The load/run
                                               switch
                     (Appendix A,sec.4.4b)     is set to run.
                                               OC print out
                                               as specified
                                               in app.B.sec.
                                               7.16
                     DO CLOSE 254(CR)
                     Appendix A,sec.4.31b)

7.16.3   N/A         Power down TU#5.
                     Remove PTP/R from
                     J25. Set switch S2 on
                     LTUX-S #25 to.
                     1: Closed
                     2: Closed
                     3: Closed
                     4: Closed
                     Power up TU#5.

7.16.4               Quit the TDX4 test by
                     entering from the OC      Refer to Appendix
                     QUIT(CR)                  B sec. 1.4

7.17                 Boot the TDX5 test as
                     follows:

                     BA 1025(CR)
                     BM 140(CR)                Refer to Appendix
                     BO 633(CR)                B sec. 7.17
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.18.1   N/A         Power down TU#5
                     Connect the TTY to J1
                     in the V24 filter box.
                     Set switch S2 on LTUX-S
                     #15 to:
                     1: CLOSED
                     2: OPEN
                     3: OPEN
                     4: OPEN
                     Power up TU#5             N/A

7.18.2   OC          Activate the link 151
                     LTUX-S test as follows:
                     Enter from the OC:        OC print out
                                               as
                     DO OPEN151(CR)            specified in
                                               appen-
                     (Appendix A, sec.4.40a)   dix B sec. 7.18.
                     DO TTY(CR)                TTY print out
                     (Appendix A, sec.4.6)     as specified
                                               in ap-
                     DO CLOSE 151(CR)          pendix B, sec.8.2
                     (Appendix A,sec.4.40b)

7.18.3   N/A         Power down TU#5. Set      N/A
                     switch S2 on LTUX-S
                     #15 to:
                     1: CLOSED
                     2: CLOSED
                     3: CLOSED
                     4: CLOSED
                     Power up to TU#5
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲2̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲P̲U̲#̲2̲/̲C̲U̲/̲T̲D̲X̲#̲2̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲S̲e̲c̲s̲.̲ ̲3̲.̲4̲.̲5̲.̲1̲.̲o̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲4̲,̲ ̲3̲.̲4̲.̲5̲.̲7̲.̲a̲.̲7̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.18.4   OC          Quit the TDX test by
                     entering from the OC:     Refer to Appendix
                     QUIT(CR)                  B, sec. 1.4

























 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR


3.2.3.2.4            T̲e̲s̲t̲ ̲T̲e̲r̲m̲i̲n̲a̲t̲i̲o̲n̲

         Power Down the system as Follows:

         a)          Depress "START" push button on Disk Drive
                     # 2 and wait until he "START" and "READY"
                     indicators are "OFF".

         b)          Remove the Disk Pack from Disk Drive #
                     2, close the lid and push the drive back
                     in rack B

         c)          The two scratch Floppy Disks are removed
                     from the Floppy Disk drive in rack C. Close
                     the lids.

         d)          The Power Switch (2) on each Mains Switch
                     is set to "OFF".

         e)          The input power switch on each Frequency
                     Stabilizer is set to "OFF"

         f)          Power Down all connected Terminals i.e.
                     VDUs, MSPs, OC, PTP/PTR, OCR as applicable.

         g)          Disconnect the OC from the leftmost V24/V28(L/L)
                     adaptor in the Adaptor crate of rack C,
                     and replace this adaptor with the originally
                     mounted OPTO transceiver.

         h)          Disconnect the two V24 cables (at the WDP
                     rear crate), remove the short extension
                     cable and reconnect the two cables to J2
                     and J3 respectively.

         i)          Interchange the TIA#1 (PU#2 rear crate,
                     slot 15) TDX connection and the TIA#2 (PU#2
                     rear crate, slot 16) TDX connection.



         j)  Set the host number on the STI (PU#2 front crate,
             slot 18) to #02 on switch S1 as follows:

             S1,4 : CLOSED
             S1,3 : CLOSED
             S1,2 : OPEN
             S1,1 : CLOSED



3.2.3.3  T̲e̲s̲t̲ ̲P̲r̲o̲c̲e̲d̲u̲r̲e̲ ̲3̲

         This testprocedure serves to verify the Watchdog Processor
         System i.e. the Watchdog Processor Unit (WDP), the
         Configuration Control Bus Adapter (CCBA), the Channel
         Unit Control Panel (CUCP), the TDX Bus Switching Modules
         (BSM-Xs) and the Configuration Control Adapters (CCAs).



3.2.3.3.1    T̲e̲s̲t̲ ̲S̲e̲t̲ ̲U̲p̲

         The test is performed via an Operator Console (OC)
         which is a printer and keyboard, a TEST VDU#1 and a
         TEST VDU#2 all with V24/V28 interface and a Medium
         Speed Printer (MSP) with OPTO interface.

         The above mentioned testequipment is connected to the
         system as follows:

             1.  Substitute the leftmost OPTO transceiver in
                 the rack C Adapter crate with a V24/V28(L/L)
                 adapter (1 channel), and connect the OC to
                 the V24 connector on the front panel of the
                 adaptor.

             2.  Connect the MSP to the remaining OPTO transceiver
                 in the Adapter crate in rack C.

             3.  Connect TEST VDU#1 to J26 in the V24 FILTER
                 BOX.



             4.  Connect TEST VDU#2 to J27 in the V24 FILTER
                 BOX.

             5.  Disconnect the two V24 cables connected to
                 the J1 and J2 connectors on the leftmost Back
                 Panel 8 located in the rear of the Adapter
                 crate.

             6.  Disconnect the V24 cable connected to the MIA
                 in PU#1 and connect TESTCABLE#1 between above
                 mentioned (para. 5) J1 and the MIA.

             7.  Disconnect the V24 cable connected to the MIA
                 in PU#2 and connect TESTCABLE#2 between above
                 mentioned (para. 5) J2 and the MIA.

             8.  Disconnect the two V24 cables connected to
                 J1 and J2 respectively on the WCA front panel
                 in the rear crate of the WDP.

             9.  Connect TESTCABLE#3 between the above mentioned
                 (para. 8) J1 and J2.

         The testequipment is now connected to the system as
         shown in fig. 3.2.3.3.1-1.

         Carry out/control the following:

         a)  OC, TEST VDU#1, TEST VDU#2, and MSP set up:

             1)  Asynchronous communication
             2)  7 bit character length
             3)  Even parity check/generation
             4)  1 stop bit
             5)  2400 Baud communication speed

         TEST VDU#1 and #2 should furthermore be set to echomode
         (ECHO=Y)


         b)  Switch settings in PU#1 and PU#2 front crate modules:

             1)  The NRM/MAIN switch on the MAP module front
                 panel is set to NRM.

             2)  The EN/DIS switch on the MAP module front panel
                 is set to EN.

             3)  The host number switch (S1) on the PU#2 STI
                 is set to #01 as follows:

                 S1,4 : CLOSED
                 S1,3 : CLOSED
                 S1,2 : CLOSED
                 S1,1 : OPEN

         c)  Switch settings in PU#1 and PU#2 rear crate modules:

             1)  The Baudrate select switches 1-4 (S1) on the
                 MAP Interface Adapter (MIA) Printed Circuit
                 Board (PCB) is set to #A which corresponds
                 to a transmission speed of 2400 Baud:

                 Switch 1:  CLOSED
                 Switch 2:  OPEN
                 Switch 3:  CLOSED
                 Switch 4:  OPEN


















































                    FIGURE 3.2.3.3.1-1

             C̲o̲n̲n̲e̲c̲t̲i̲o̲n̲ ̲o̲f̲ ̲t̲h̲e̲ ̲t̲e̲s̲t̲e̲q̲u̲i̲p̲m̲e̲n̲t̲


             2)  a)  The RESET switch on the Configuration Control
                     Adaptor (CCA) front panel is set away from
                     RESET.

                 b)  PU#1:
                     The CCA address switch on the CCA printed
                     circuit board (PCB) is set to 01 hexadecimal.
                     PU#2:
                     The CCA address switch on the CCA printed
                     circuit board (PCB) is set to 02 hexadecimal.

         d)  Switch settings in CU front crate modules.

             1)  Switches on the Channel Unit Control Panel
                 (CUCP) front panel is set as:

                 a)  The CU Bus A Switch DIS/AUTO is set to
                     AUTO

                 b)  The CU Bus B switch DIS/AUTO is set to
                     AUTO

                 c)  The Disk Ctrl. No. 1 switch AAEN/AUTO/BAEN
                     is set to AUTO

                 d)  The Disk Ctrl. No. 2 switch AAEN/AUTO/BAEN
                     is set to AUTO

                 e)  The Disk Ctrl. No. 3 switch AAEN/AUTO/BAEN
                     is set to AUTO

                 f)  The LTU No. 1 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 g)  The LTU No. 2 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 h)  The LTU No. 3 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 i)  The LTU No. 4 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 k)  The LTU No. 5 switch AAEN/AUTO/BAEN is
                     set to AUTO

                 l)  The SD.FD.CTRL switch AAEN/AUTO/BAEN is
                     set to AUTO


         e)  Switch settings in CU rear crate modules:

             1)  a)  The RESET switch on the CCA module front
                     panel is set away from RESET

                 b)  The CCA address switch on the CCA printed
                     circuit board (PCB) is set to 03 hexadecimal.

         f)  Switch settings in WDP rear crate modules:

             1)  The EN/DIS switch on the front panel of the
                 CCBA is set to DIS.

         g)  Switch settings in TU modules

             1)  All BSM-Xs:

                 a)  The AUTO/MAN/OFF switch is set to AUTO.

                 b)  The BUS 1/Bus 2 switch is set to BUS 1.

                 c)  The address switch on each BSM-X is set
                     to 1X hexadecimal, where X equals the number
                     of the TU in which the actual BSM-X is
                     placed. E. g. the BSM-X in TU#5 is given
                     the address 15 hexadecimal. (This should
                     be carried out prior to the test but can
                     be verified at this point).

             2)  All LTUX-Ss:

                 a)  The CH 1 switch ON/OFF is set to ON

                 b)  The CH 2 switch ON/OFF is set to ON

                 c)  The CH 3 switch ON/OFF is set to ON

                 d)  The CH 4 switch ON/OFF is set to ON

         h)  Switch settings on frequency stabilizer rack:

             1)  The input power switch on all three stabilizers
                 are set to off.

             2)  The three rotary switches on the By-Pass panel
                 are all set to the Frequency Stabilizer position.


         i)  Setting of power switches in Computer racks:

             1)  Power switch (2) on each Mains switch is set
                 to "OFF".

             2)  Power switch (2) on the Disk Drive rear panel
                 is set to "ON"

             3)  Power switch (1) on the Floppy Disk Drive rear
                 panel is set to "ON".

             4)  Power switch (1) on the Watchdog Processor
                 Unit rear panel is set to "ON".

             5)  Power switch (2) in the rear crate of PU#1
                 is set to "ON"

             6)  Power switch (2) in the rear crate of the CU
                 is set to "ON"

             7)  Power switch (2) in the rear crate of the PU#2
                 is set to "ON".

             8)  Power switch (2) in the rear panel of each
                 80D fan unit is set to "ON".

             9)  Power switch (2) in the rear crate of the Adaptor
                 Crate is set to "ON"

             10) Power switch (1) in the rear panel of the 80S
                 Blower Unit is set to "ON"

             11) Power switch (1) on each CR80D Power supply
                 (6 front crate mounted modules) is set to "ON".

         k)  Setting of Power Switche in Line Termination racks:

             1)  Power Switch (2) on each Mains Switch is set
                 to "OFF".

             2)  Power Switch (1) on the rear panel of each
                 80S Blower Unit is set to "ON".

             3)  Power Switch (2) in the rear crate of each
                 TU is set to "ON".


             4)  Power Switch (1) on each CR80S Power Supply
                 (1 in the front crate of each TU) is set to
                 "ON".

         k)  PU#2 cable interchanges

             Interchange the TIA#1 (rear crate, slot 15) TDX
             connection and the TIA#2 (rear crate, slot 16)
             TDX connection.

3.2.3.3.2    T̲e̲s̲t̲ ̲I̲n̲i̲t̲i̲a̲l̲i̲z̲a̲t̲i̲o̲n̲

         The testengineers and testwitnesses are in the testroom
         and ready to perform and supervise the test.

         Power Up the System as follows:

         a)  Power Up all connected terminals i.e. VDUs, MSPs,
             OC, PTP/PTR, as applicable.

         b)  The input Power Switch on the front panel of each
             Frequency Stabilizer is set to "ON".

         c)  The power switch (2) on Mains switch no. 1 is set
             to "ON" wait 15 secs.

         d)  The power switch (2) on each of the remaining Mains
             Switches is set to "ON".

         e)  Mount a Disk Pack with the test software in Disk
             Drive no. 2, close the lid and push the drive back
             in rack B. Activate the WRITE PROTECT pushbutton.

         f)  Activate "START" push button on Disk Drive No.
             2 and wait until the "READY" indicator stays "ON".

         g)  Insert a scratch Floppy Disk in each of the two
             drives in the Floppy Disk drive of rack B, and
             close the lids.


3.2.3.3.3    T̲e̲s̲t̲ ̲S̲t̲e̲p̲s̲

         The teststeps for testgroup no. 2, testprocedure no.
         3 (2/3), is given in the following preceded by a testoverview.




T̲E̲S̲T̲ ̲O̲V̲E̲R̲V̲I̲E̲W̲                                  T̲E̲S̲T̲ ̲N̲O̲.̲:̲ ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲C̲a̲p̲a̲b̲i̲l̲i̲t̲i̲e̲s̲              
    

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

Test Case/
Reference        Action                        SRS Reference
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

All              WDP test                      N/A

1.               WDP V24 interfaces            N/A

2.               WDP CCBA interface            N/A

3.               PU#1 CCA test                 N/A

4.               PU#2 CCA test                 N/A

5.               CU CCA test                   N/A

6.               TU#1 BSM-X test               N/A

7.               TU#2 BSM-X test               N/A

8.               TU#3 BSM-X test               N/A

9.               TU#4 BSM-X test               N/A



T̲E̲S̲T̲ ̲O̲V̲E̲R̲V̲I̲E̲W̲                                  T̲E̲S̲T̲ ̲N̲O̲.̲:̲ ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲F̲u̲n̲c̲t̲i̲o̲n̲a̲l̲ ̲C̲a̲p̲a̲b̲i̲l̲i̲t̲i̲e̲s̲              
    

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

Test Case/
Reference        Action                        SRS Reference
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲

10.              TU#5 BSM-X test               N/A

11.              TU#7 BSM-X test               N/A

12.              TU#11 BSM-X test              N/A




T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

1.1      N/A         The EN/DIS switch on      N/A
                     the CCBA front panel
                     is set to EN

1.2      OC          Examine print out on      Refer to appendix
                                               B
                     the OC.                   sec 9.1

1.3                  Enter from the OC:
                     PUANSW(SP)D(CR)           Refer to appendix
                                               B
                     CCA(SP)1-3(CR)            sec. 9.2
                     BSMX(SP)11-15(CR)
                     BSMX(SP)17(CR)
                     BSMX(SP)1B(CR)
                     CCBUM(CR)

1.4      N/A         Examine TEST VDU#1 and    Displays in compli-
                     TEST VDU#2 displays       ance with appendix
                                               B
                                               sec. 1.1

1.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     PU1(CR)                   sec. 9.3
                     10 01 00 00
                     54 45 53 54(CR)





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

1.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     PU2(CR)                   sec. 9.4
                     10 02 00 00
                     54 45 53 54(CR)

1.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     LPR(CR)                   sec. 9.5
                     10 01 00 00 0D 0A 54      MSP print out:
                     45 53 54 1B 48 0D(CR)     (CR)(LF)TEST
                                               (Formfeed)


















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

2.1      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.1
                     A4 01 03(CR)

2.2      N/A         The EN/DIS switch on      N/A
                     the CCBA front panel
                     is set to DIS

2.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.2
                     A4 01 03(CR)

2.4      N/A         The EN/DIS switch on      N/A
                     the CCBA front panel
                     is set to EN













 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.1      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.3
                     A4 01 0E(CR)

3.2      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.4
                     A4 01 01(CR)

3.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.5
                     A4 01 02(CR)

3.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.6
                     A4 01 03(CR)

3.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.7
                     A4 01 0F(CR)

3.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.8
                     94 01 0F 00(CR)





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.9
                     98 01 0F 00 00 00(CR)

3.8                  Intentionally deleted     

3.9      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.10
                     98 01 0F 00 01 00(CR)     (Disable PU#1)

3.10     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.11
                     94 01 0F 00(CR)

3.11     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.12
                     98 01 0F 00 04 00(CR)     (Enable PU#1,
                                               Maintenance mode)










 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.12     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.13
                     94 01 0F 00(CR)

3.13     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.14
                     98 01 0F 00 0C 00(CR)     (Set Master Clear
                                               PU#1, Maintenance
                                               Mode)

3.14     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

3.15     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.15
                     98 01 0F 00 04 00(CR)     (Release Master
                                               Clear PU#1, Maintenance
                                               Mode)









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR
                                                …86…1         …02… 
                                                        …02…   
                                                           
                                                       …02…    
                                                           
                                                  

T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

3.16     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.16
                     98 01 0F 00 00 00(CR)     (PU#1 Normal
                                               Mode)

3.17     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.17
                     98 01 0F 00 08 00(CR)     (Set Master Clear
                                               PU#1, Normal
                                               Mode)

3.18     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

3.19     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 10.18
                     98 01 0F 00 00 00(CR)     (Release Master
                                               Clear PU#1, Normal
                                               Mode)

3.20     N/A         Examine TEST VDU#1        Display in accordance
                     Display                   with appendix
                                               B sec. 1.1







 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

4.1      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.1
                     A4 02 0E(CR)

4.2      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.2
                     A4 02 01(CR)

4.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.3
                     A4 02 02(CR)

4.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.4
                     A4 02 03(CR)

4.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.5
                     A4 02 0F(CR)

4.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.6
                     94 02 0F 00(CR)





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

4.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.7
                     98 02 0F 00 00 00(CR)

4.8                  Intentionally deleted

4.9      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.8
                     98 02 0F 00 01 00(CR)     (PU#2 disable)

4.10     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.9
                     94 02 0F 00(CR)

4.11     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.10
                     98 02 0F 00 04 00(CR)     (PU#2 enable,
                                               Maintenance Mode)










 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

4.12     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.11
                     94 02 0F 00(CR)

4.13     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.12
                     98 02 0F 00 0C 00(CR)     (Set Master Clear
                                               PU#2, Maintenance
                                               Mode)

4.14     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

4.15     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.13
                     98 02 0F 00 04 00(CR)     (Release Master
                                               Clear PU#2, Maintenance
                                               Mode)









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR
                                                …86…1         …02… 
                                                        …02…   
                                                           
                                                       …02…    
                                                           
                                                  

T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

4.16     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.14
                     98 02 0F 00 00 00(CR)     (PU#2 Normal
                                               Mode)

4.17     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.15
                     98 02 0F 00 08 00(CR)     (Set Master Clear
                                               PU#2, Normal
                                               Mode)

4.18     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

4.19     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 11.16
                     98 02 0F 00 00 00(CR)     (Release Master
                                               Clear PU#2, Normal
                                               Mode)

4.20     N/A         Examine TEST VDU#2        Display in accordance
                     Display                   with appendix
                                               B sec. 1.1







 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.1      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

5.2      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

5.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.1
                     A4 03 0E(CR)

5.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.2
                     A4 03 01(CR)

5.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.3
                     A4 03 02(CR)

5.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.4
                     A4 03 03(CR)





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
5.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.5
                     A4 03 0F(CR)

5.8      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.6
                     A4 03 06(CR)

5.9      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.7
                     A4 03 07(CR)

5.10     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.8
                     A4 03 08(CR)

5.11     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.9
                     94 03 0F 00(CR)

5.12     N/A         The CU Bus A DIS/AUTO     N/A
                     switch on the CUCP
                     front panel is set to
                     DIS.

5.13     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.10
                     94 03 0F 00(CR)

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.14     N/A         The CU Bus A DIS/AUTO     N/A
                     switch on the CUCP
                     front panel is set to
                     AUTO.

5.15     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.11
                     98 03 0F 00 00 00(CR)

5.16                 Intentionally deleted

5.17     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.12
                     98 03 0F 00 04 00(CR)     (Disable CU Bus
                                               A)

5.18     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

5.19     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.






 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.20     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU #1 display
                     IR 1A25(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.1

5.21     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU #1 display
                     IR 1A01(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.2

5.22     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU #1 display
                     IR 1A07(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.3

5.23     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU #2 display
                     IR 1A25(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.4

5.24     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU #2 display
                     IR 1A01(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.5

5.25     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU #2 display
                     IR 1A07(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.6





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.26     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

5.27     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

5.28     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 12.13
                     98 03 0F 00 08 00(CR)     (Disable CU Bus
                                               B, Enable CU
                                               Bus A)

5.29     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU #1 display
                     IR 1A25(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.4

5.30     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU #1 display
                     IR 1A01(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.5








 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

5.31     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU #1 display
                     IR 1A07(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.6

5.32     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU #2 display
                     IR 1A25(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.1

5.33     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU #2 display
                     IR 1A01(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.2

5.34     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU #2 display
                     IR 1A07(CR)               as specified
                                               in ap-
                                               pendix B, sec.
                                               24.3

5.35     OC          Enter from the OC:        Refer to appendix
                                               D
                     CCB(CR)                   sec. 12.14
                     98 03 0F 00 00 00(CR)     (Enable CU Bus
                                               A and B)








 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.1      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

6.2      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

6.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.1
                     A4 11 00(CR)

6.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.2
                     A4 11 01(CR)

6.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.3
                     A4 11 02(CR)

6.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.4
                     A4 11 03(CR)

6.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.5
                     A4 11 04(CR)

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.8      TESTVDU#1   Boot the TDX1 test        TEST VDU#1 display
                                               in
                     program as follows:       accordance with
                                               appen-
                     BA 1025                   dix B sec. 7.1
                     BM 140
                     BO 62F

6.9      TESTVDU#2   Boot the TDX1 test        TEST VDU#2 display
                                               in
                     program as follows:       accordance with
                                               appen-
                     BA 1025                   dix B sec. 7.1
                     BM 140
                     BO 62F

6.10     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.6
                     94 11 FF FF(CR)

6.11     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.7
                     98 11 FF 00 02 00(CR)     (Switch on TDX
                                               BUS#1)

6.12     TESTVDU#1   Enter from TEST VDU#1:    
                     DO OPEN1(CR)              
                     (Appendix A, sec. 4.7a)   Test VDU#1 display
                                               as 
                     DO CLOSE1(CR)             specified in
                                               appendix 
                     (Appendix A, sec. 4.7b)   B sec. 24.7
                                               
                     

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.13     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                     DO OPEN1(CR)              as specified
                                               in
                     (Appendix A, sec. 4.7a)   appendix B, sec.
                     DO CLOSE1(CR)             24.8
                     (Appendix A, sec. 4.7b)   

6.14     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

6.15     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

6.16     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 13.8
                     98 11 FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)











 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

6.17     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU#1 display
                     DO OPEN1(CR)              as specified
                                               in
                     (Appendix A, sec. 4.7a)   appendix B, sec.
                     DO CLOSE1(CR)             24.8
                     (Appendix A, sec. 4.7b)   

6.18     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                                               as
                     DO OPEN1(CR)              specified in
                                               appendix
                     (Appendix A, sec. 4.7a)    B sec. 24.7
                     DO CLOSE1(CR)             
                     (Appendix A, sec. 4.7b)

















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.1      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

7.2      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

7.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.1
                     A4 12 00(CR)

7.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.2
                     A4 12 01(CR)

7.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.3
                     A4 12 02(CR)

7.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.4
                     A4 12 03(CR)

7.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.5
                     A4 12 04(CR)

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.8      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.6
                     94 12 FF FF(CR)

7.9      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.7
                     98 12 FF 00 02 00(CR)     (Switch on TDX
                                               BUS#1)

7.10     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU#1 display
                                               as 
                     DO OPEN2(CR)              specified in
                                               appendix 
                     (Appendix A, sec. 4.8a)   B sec. 24.9
                     DO CLOSE2(CR)             
                     (Appendix A, sec. 4.8b)   

7.11     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                     DO OPEN2(CR)              as specified
                                               in
                     (Appendix A, sec. 4.8a)   appendix B, sec.
                     DO CLOSE2(CR)             24.10
                     (Appendix A, sec. 4.8b)   
                                                                     







 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.12     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

7.13     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

7.14     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 14.8
                     98 12 FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)

7.15     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU#1 display
                     DO OPEN2(CR)              as specified
                                               in
                     (Appendix A, sec. 4.8a)   appendix B, sec.
                     DO CLOSE2(CR)             24.10
                     (Appendix A, sec. 4.8b)   
                                                                     









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

7.16     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                                               as 
                     DO OPEN2(CR)              specified in
                                               appendix
                     (Appendix A, sec. 4.8a)    B sec. 24.9
                     DO CLOSE2(CR)             
                     (Appendix A, sec. 4.8b)   
                                               






















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

8.1      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

8.2      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

8.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.1
                     A4 13 00(CR)

8.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.2
                     A4 13 01(CR)













 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

8.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.3
                     A4 13 02(CR)

8.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.4
                     A4 13 03(CR)

8.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.5
                     A4 13 04(CR)

8.8      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.6
                     94 13 FF FF(CR)

8.9      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.7
                     98 13 FF 00 02 00(CR)     (Switch on TDX
                                               BUS#1)









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

8.10     TESTVDU#1   Enter from TEST VDU#1:    TEST VDU#1 display
                                               as
                     DO OPEN13(CR)             specified in
                                               appendix
                     (Appendix A, sec. 4.9a)   B sec. 24.11
                     DO CLOSE13(CR) 
                     (Appendix A, sec. 4.9b) 

8.11     TESTVDU#2   Enter from TEST VDU#2:    
                     DO OPEN13(CR)             TEST VDU#2
                     (Appendix A, sec. 4.9a)   display as speci-
                     DO CLOSE13(CR)            fied in appendix
                                               B,
                     (Appendix A, sec. 4.9b)   sec. 24.12

8.12     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.













 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

8.13     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

8.14     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 15.8
                     98 13 FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)

8.15     TESTVDU#1   Enter from TEST VDU#1:     
                     DO OPEN13(CR)             TEST VDU#1
                     (Appendix A, sec. 4.9a)   display as speci-
                     DO CLOSE13(CR)            fied in appendix
                                               B,
                     (Appendix A, sec. 4.9b)   sec. 24.12

8.16     TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                                               as
                     DO OPEN13(CR)             specified in
                                               appendix
                     (Appendix A, sec. 4.9a)    B sec. 24.11
                     DO CLOSE13(CR)            
                     (Appendix A, sec. 4.9b)                         








 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

9.1      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

9.2      N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.





















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

9.3      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.1
                     A4 14 00(CR)

9.4      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.2
                     A4 14 01(CR)

9.5      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.3
                     A4 14 02(CR)

9.6      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.4
                     A4 14 03(CR)

9.7      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.5
                     A4 14 04(CR)









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

9.8      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.6
                     94 14 FF FF(CR)

9.9      OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.7
                     98 14 FF 00 02 00(CR)     (SWITCH ON TDX
                                               BUS#1)

9.10     TESTVDU#1   Enter from TEST VDU#1:                            DO
                                                                       OPEN14(CR) 
                                                                                  
                     (Appendix A, sec. 4.12a)   
                     DO CLOSE14(CR)            TEST VDU#1 display
                                               as
                     (Appendix A, sec. 4.12b)  specified in
                                               appendix B sec.
                                               24.13

9.11     TESTVDU#2   Enter from TEST VDU#2:    
                     DO OPEN14(CR)             TEST VDU#2 display
                     (Appendix A, sec. 4.12a)  as specified
                                               in
                     DO CLOSE14(CR)            appendix B, sec.
                                               24.14
                     (Appendix A, sec. 4.12b)








 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

9.12     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

9.13     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

9.14     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 16.8
                     98 14 FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)

9.15     TESTVDU#1   Enter from TEST VDU#1:    
                     DO OPEN14(CR)             TEST VDU#1 display
                     (Appendix A, sec. 4.12a)  as specified
                                               in
                     DO CLOSE14(CR)            appendix B, sec.
                                               24.14
                     (Appendix A, sec. 4.12a)      
                     
                     









 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

9.16     TESTVDU#2   Enter from TEST VDU#2:    
                     DO OPEN14(CR)             TEST VDU#2 display
                                                                       (Appendix
                                                                       A,
                                                                       sec.
                                                                       4.12a) as
                                                                              specified
                                                                              in   DO
                                                                                   CLOSE14(CR) appendix
                                                                                               B
                                                                                               sec.
                                                                                               24.13
                     (Appendix A, sec. 4.12b)                        
9.17     TESTVDU#1/  Quit the TDX1 test by     TEST VDUs #1,
                                               #2 dis-
         TESTVDU#2   entering from TEST VDU#1  play as shown
                                               in
                     and TEST VDU#2: QUIT(CR)  appendix B sec.
                                               1.4.



















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

10.1     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

10.2     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

10.3     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.1
                     A4 15 00(CR)

10.4     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.2
                     A4 15 01(CR)

10.5     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.3
                     A4 15 02(CR)

10.6     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.4
                     A4 15 03(CR)

10.7     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.5
                     A4 15 04(CR)

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

10.8     TESTVDU#1   Boot the TDX2 test        TEST VDU#1 display
                                               in
                     program as follows:       accordance with
                                               appen-
                     BA 1025                   dix B sec. 7.7
                     BM 140
                     BO 630

10.9     TESTVDU#2   Boot the TDX2 test        TEST VDU#2 display
                                               in
                     program as follows:       accordance with
                                               appen-
                     BA 1025                   dix B sec. 7.7
                     BM 140
                     BO 630

10.10    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.6
                     94 15 FF FF(CR)

10.11    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.7
                     98 15 FF 00 02 00(CR)     (Switch on TDX
                                               BUS#1)

10.12    TESTVDU#1   Enter from TEST VDU#1:    
                     DO OPEN15(CR)             TEST VDU#1 display
                                               
                     (Appendix A, sec. 4.14a)  as specified
                                               in
                     DO CLOSE15(CR)            appendix B sec.
                                               24.15
                     (Appendix A, sec. 4.14b)



 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

10.13    TESTVDU#2   Enter from TEST VDU#2:    
                     DO OPEN15(CR)             TEST VDU#2 display
                     (Appendix A, sec. 4.14a)  as specified
                                               in
                     DO CLOSE15(CR)            appendix B, sec.
                     (Appendix A, sec. 4.14b)  24.16
                     
10.14    N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

10.15    N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

10.16    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 17.8
                     98 15 FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)











 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

10.17    TESTVDU#1   Enter from TEST VDU#1:    
                     DO OPEN15(CR)             TEST VDU#1              (Appendix
                                                                       A,
                                                                       sec.
                                                                       4.14a) display
                                                                              as
                                                                              specified
                     DO CLOSE15(CR)            in appendix B,
                                               sec.
                     (Appendix A, sec. 4.14b)  24.16

10.18    TESTVDU#2   Enter from TEST VDU#2:    
                     DO OPEN15(CR)             TEST VDU#2 display
                     (Appendix A, sec. 4.14a)  as specified
                                               in
                     DO CLOSE15(CR)            appendix B,sec.
                                               24.15
                     (Appendix A, sec. 4.14b)  

















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

11.1     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

11.2     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

11.3     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.1
                     A4 17 00(CR)

11.4     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.2
                     A4 17 01(CR)

11.5     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.3
                     A4 17 02(CR)

11.6     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.4
                     A4 17 03(CR)





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

11.7     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.5
                     A4 17 04(CR)

11.8     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.6
                     94 17 FF FF(CR)

11.9     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.7
                     98 17 FF 00 02 00(CR)     (Switch on TDX
                                               BUS#1)

11.10    TESTVDU#1   Enter from TEST VDU#1:    TEST VDU#1 display
                                               as
                     DO OPEN17(CR)             specified in
                                               appendix
                     (Appendix A, sec. 4.9a)   B sec. 24.17
                     DO CLOSE17(CR) 
                     (Appendix A, sec. 4.9b) 

11.11    TESTVDU#2   Enter from TEST VDU#2:    
                     DO OPEN17(CR)             TEST VDU#2
                     (Appendix A, sec. 4.9a)   display as speci-
                     DO CLOSE17(CR)            fied in appendix
                                               B,
                     (Appendix A, sec. 4.9b)   sec. 24.18





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

11.12    N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

11.13    N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

11.14    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 18.8
                     98 17 FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)

11.15    TESTVDU#1   Enter from TEST VDU#1:     
                     DO OPEN17(CR)             TEST VDU#1
                     (Appendix A, sec. 4.9a)   display as speci-
                     DO CLOSE17(CR)            fied in appendix
                                               B,
                     (Appendix A, sec. 4.9b)   sec. 24.18

11.16    TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                                               as
                     DO OPEN17(CR)             specified in
                                               appendix
                     (Appendix A, sec. 4.9a)    B sec. 24.17
                     DO CLOSE17(CR)            
                     (Appendix A, sec. 4.9b)





 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

11.17    Test VDU#1  Quit the TDX2 test by
         Test VDU#2  entering from Test VDU#1
                     and Test VDU#2: QUIT(CR)  Test VDU's #1,
                                               #2 
                                               display as shown
                                               in
                                               Appendix B, sec.
                                               1.4

11.18    Test VDU#1  Boot the TDX3 test
                     program as follows:
                     BA 1025
                     BM 140
                     BO 631                    Test VDU #1 display
                                               in
                                               accordance with
                                               Appen-
                                               dix B, sec. 7.10















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

11.19    Test VDU#2  Boot the TDX3 test 
                     program as follows:
                     BA 1025
                     BM 140
                     BO 631                    Test VDU#2 display
                                               in
                                               accordance with
                                               Appen-
                                               dix B, sec. 7.10.





















 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

12.1     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

12.2     N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

12.3     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.1
                     A4 1B 00(CR)

12.4     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.2
                     A4 1B 01(CR)

12.5     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.3
                     A4 1B 02(CR)

12.6     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.4
                     A4 1B 03(CR)

12.7     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.5
                     A4 1B 04(CR)

 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

12.8     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.6
                     94 1B FF FF(CR)

12.9     OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.7
                     98 1B FF 00 02 00(CR)     (Switch on TDX
                                               BUS#1)

12.10    TESTVDU#1   Enter from TEST VDU#1:    
                     DO OPEN 1B (CR)           TESTVDU#1 display
                                               as
                     (Appendix A, sec. 4.24a)  specified in
                                               appendix
                     DO CLOSE 1B (CR)          B sec. 24.19
                                               
                     (Appendix A, sec. 4.24b)  
                     














 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

12.11    TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#2 display
                     DO OPEN 1B (CR)           as specified
                                               in
                     (Appendix A, sec. 4.24a)  appendix B, sec.
                     DO CLOSE1B(CR)            24.20
                     (Appendix A, sec. 4.24b)

12.12    N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#1.

12.13    N/A         Depress both …08…CONTROL      N/A
                     SHIFT…08… and …08…CLEAR…08…
                     on TEST VDU#2.

12.14    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.8
                     98 1B FF 00 01 00(CR)     (Switch on TDX
                                               BUS#2)











 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:





                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

12.15    TESTVDU#1   Enter from TEST VDU#1:    TEST VDU#1 display
                     DO OPEN 1B (CR)           as specified
                                               in
                     (Appendix A, sec. 4.24a)  appendix B, sec.
                     DO CLOSE 1B (CR)          24.20
                     (Appendix A, sec. 4.24b)

12.16    TESTVDU#2   Enter from TEST VDU#2:    TEST VDU#1 display
                     DO OPEN 1B (CR)           as specified
                                               in
                     (Appendix A, sec. 4.24a)  appendix B, sec.
                     DO CLOSE 1B (CR)          24.19
                     (Appendix A, sec. 4.24b)

12.17    TESTVDU#2   Quit the TDX3 test by     TEST VDU#1,#2
         TESTVDU#2   entering from TEST        display as shown
                     VDU#1 and TEST VDU#2:     in appendix B
                                               sec. 1.4
                     QUIT












 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:


                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR



T̲E̲S̲T̲ ̲S̲T̲E̲P̲S̲                                                           T̲E̲S̲T̲
                                                                     ̲N̲O̲.̲:̲
                                                                     ̲2̲/̲3̲

F̲U̲N̲C̲T̲I̲O̲N̲:̲ ̲ ̲W̲a̲t̲c̲h̲d̲o̲g̲ ̲P̲r̲o̲c̲e̲s̲s̲o̲r̲ ̲S̲y̲s̲t̲e̲m̲ ̲T̲e̲s̲t̲

S̲R̲S̲ ̲R̲E̲F̲E̲R̲E̲N̲C̲E̲:̲ ̲ ̲N̲/̲A̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

Case     Test
Step No. Station     Action                    Expected Results
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲

12.18    N/A         If the CH1.ERR.indica-    N/A
                     tion is on activate the
                     RESET pushbutton on the
                     RESYNC MODULE.

12.19    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec. 19.9
                     94 1B FF FF(CR)

12.20    N/A         Power down the remote     After 13.5 secs.the
                     site stat.mux.            CH1.ERR indication
                                               goes on.
                     Power up the remote
                     site stat.mux.

12.21    OC          Enter from the OC:        Refer to appendix
                                               B
                     CCB(CR)                   sec.19.10
                     94 1B FF FF(CR)

12.22    N/A         Activate the RESET push-  CH1.ERR.indication
                     button on the RESYNC      goes off.
                     MODULE 

12.23    OC          Enter from the OC:        Refer to sppendix
                                               B
                     CCB(CR)                   sec.19.9
                     94 1B FF FF(CR)


 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
 ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
Comments:


                                                ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲ ̲
                                               ̲ ̲
                                               T̲E̲S̲T̲ ̲W̲I̲T̲N̲E̲S̲S̲E̲S̲

                                               TEST QA   QAR


3.2.3.3.4            T̲e̲s̲t̲ ̲T̲e̲r̲m̲i̲n̲a̲t̲i̲o̲n̲

         Power Down the system as Follows:

         a)          Depress "START" push button on Disk Drive
                     # 2 and wait until he "START" and "READY"
                     indicators are "OFF".

         b)          Remove the Disk Pack from Disk Drive #
                     2, close the lid and push the drive back
                     in rack B

         c)          The two scratch Floppy Disks are removed
                     from the Floppy Disk drive in rack C. Close
                     the lids.

         d)          The Power Switch (2) on each Mains Switch
                     is set to "OFF".

         e)          The input power switch on each Frequency
                     Stabilizer is set to "OFF"

         f)          Power Down all connected Terminals i.e.
                     VDUs, MSPs, OC, OCR, as applicable.

         g)          Disconnect the OC from the leftmost V24/V28(L/L)
                     adaptor in the Adaptor crate of rack C,
                     and replace this adaptor with the originally
                     mounted OPTO transceiver.

         h)          Disconnect TEST VDU#1 from J26 in the V24
                     FILTER BOX.

         i)          Disconnect TEST VDU#2 from J27 in the V24
                     FILTER BOX.

         k)          Disconnect TESTCABLE#1 from the MIA in
                     PU#1 and reconnect the originally connected
                     cable.

         l)          Disconnect and remove TESTCABLE#1 from
                     the J1 connector on the leftmost Back Panel
                     8 in the rear of the Adapter crate. Reconnect
                     to J1 the originally connected cable.



         m)  Disconnect TESTCABLE#2 from the MIA in PU#2 and
             reconnect the originally connected cable.

         n)  Disconnect and remove TESTCABLE#2 from the J2 connector
             on the leftmost Back Panel 8 in the rear of the
             Adapter crate. Reconnect to J2 the originally connected
             cable.

         o)  Disconnect TESTCABLE#3 from both J1 and J2 on the
             WCA front panel in the WDP rear crate. Remove TESTCABLE#3
             and reconnect to J1 and J2 respectively the originally
             connected cables.

         p)  Interchange the TIA#1 (PU#2-rear crate, slot 15)
             TDX connection and the TIA#2 (PU#2-rear crate,
             slot 16) TDX connection.

         q)  Set the host number on the STI (PU#2 front crate,
             slot 18) to #02 on switch S1 as follows:

             S1,4 : CLOSED
             S1,3 : CLOSED
             S1,2 : OPEN
             S1,1 : CLOSED