|
DataMuseum.dkPresents historical artifacts from the history of: CP/M |
This is an automatic "excavation" of a thematic subset of
See our Wiki for more about CP/M Excavated with: AutoArchaeologist - Free & Open Source Software. |
top - metrics - download
Length: 8576 (0x2180)
Types: RcTekst
Names: »99110325.WP«
└─⟦6fdfe4d4d⟧ Bits:30005866/disk5.imd Dokumenter i RcTekst format (RCSL 99-1-*)
└─⟦this⟧ »99110325.WP«
╱04002d4e0a0006000000000301423100000000000000000000000000000000000000000000000000050f19232d37414b555f69737d8791ff04╱
════════════════════════════════════════════════════════════════════════
↓
┆14┆┆b3┆┆06┆ ┆0b┆↲
↲
┆b0┆┆a1┆┆b0┆┆b0┆1┆f0┆┆b0┆. INTRODUCTION↲
↲
┆84┆This manual and the references in appendix A includes ↓
┆19┆┆89┆┄┄information to opgrade the RC3902 unit with additional ↓
┆19┆┆89┆┄┄intelligent communication boards. The only HW difference ↓
┆19┆┆89┆┄┄between F641 and F642 is the EPROM's and some small ↓
┆19┆┆89┆┄┄modification of the printed board. (These modifications ↓
┆19┆┆89┆┄┄do not affect jumpers or internal cabling). The Ref 8. is ↓
┆19┆┆89┆┄┄a prerequisite for this manual.↲
↲
┆b0┆┆a1┆2. GENERAL DESCRIPTION OF RC3931↲
↲
┆84┆The RC3931 Comminication Processor is a functional unit ↓
┆19┆┆89┆┄┄which can be built into an RC3902 processor unit as a ↓
┆19┆┆89┆┄┄subsystem. It includes an ETC611 communication CPU board. ↓
┆19┆┆89┆┄┄RC3931 communicate with the communication boards F64X.↲
════════════════════════════════════════════════════════════════════════
↓
┆b0┆┆a1┆3. PLACE IN CARD CASE↲
↲
┆84┆The ETC611 is installed in slot one the first ↓
┆19┆┆89┆┄┄communications board in position two and the last in ↓
┆19┆┆89┆┄┄position three (See fig 3.1).↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
Fig 3.1 Card positions on the backplane BPL606.↲
════════════════════════════════════════════════════════════════════════
↓
┆b0┆┆a1┆4. EXTERNAL CONNECTIONS↲
↲
┆84┆The section describes external connections from F64X.↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
Fig 4.1 ┆84┆Connectors at backpanel of RC3902. For further ↓
┆19┆┆92┆┄┄informations, see table 4.1.↲
↲
════════════════════════════════════════════════════════════════════════
↓
┆a1┆ Name External device Plug type External cable ↲
↲
J11-J14 Hosts 25 pol d sub F CBL604, X21.↲
J51 Circuit 5 pol DIN M KBL604.↲
--------------------------------------------------------↲
↲
Table 4.1 ┆84┆External connections to F64X. Note that it is ↓
┆19┆┆93┆┄┄possible to change from X21 interface to V24 ↓
┆19┆┆93┆┄┄interface on the connectors J1 and J11 to J14. ↓
┆19┆┆93┆┄┄F : Female and M : Male.↲
↲
┆84┆* ┆84┆KBL620 is only used in micronet (1 Mbit/Sec).↲
════════════════════════════════════════════════════════════════════════
↓
┆b0┆┆a1┆5. INTERNAL CONNECTIONS↲
↲
┆84┆The section describes the internal connections. (See fig ↓
┆19┆┆89┆┄┄5.1.).↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
Fig 5.1 ┆84┆Inside the RC3931 computer with local net on the ↓
┆19┆┆92┆┄┄ETC611 and two communication boards F641 or ↓
┆19┆┆92┆┄┄F642. (COM601 or COM602).↲
════════════════════════════════════════════════════════════════════════
↓
┆a1┆Name Board Plug type at board Internal cable. ↲
↲
J2 ETC611 10 pol Flat F KBL720, LED603.↲
J3 ETC611 20 pol Mini Latch KBL662, V24 *.↲
J4 ETC611 26 pol Mini Latch KBL719, X21.↲
J5 ETC611 16 pol Mini Latch KBL595, LAN.↲
J2 COM60X 10 pol Mini Latch KBL687, circuit 1.↲
J3 COM60X 26 pol Mini Latch KBL719, X21.↲
J4 COM60X 26 pol Mini Latch KBL719, X21.↲
J5 COM60X 10 pol Mini Latch KBL727, LED603.↲
-------------------------------------------------------↲
↲
Table 5.1 ┆84┆Internal connections in RC3931 with ETC611 and ↓
┆19┆┆93┆┄┄two Communication board. F : Female and M : ↓
┆19┆┆93┆┄┄Male.↲
↲
* ┆84┆Note that this cable is CPU610's test consol cable. It ↓
┆19┆┆8b┆┄┄is never included in the standard RC3902 configuration ↓
┆19┆┆8b┆┄┄with CPU691.↲
════════════════════════════════════════════════════════════════════════
↓
┆b0┆┆a1┆┆b0┆┆a1┆┆b0┆┆a1┆6. JUMPERS↲
↲
┆84┆Jumpers on the first and the second communication board ↓
┆19┆┆89┆┄┄is described in this section. Note that if MEX611 is ↓
┆19┆┆89┆┄┄installed on RC3931 (ETC611), then change the jumpers on ↓
┆19┆┆89┆┄┄RC3931. (See ref 8).↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
↲
Fig 6.1 Jumper locations on the F64X.↲
╞ ╞ ↲
↲
┆84┆In Pos 2 an EPROM ROC 448 (COM601) or ROC 449 (COM602) is ↓
┆19┆┆89┆┄┄mounted.↲
════════════════════════════════════════════════════════════════════════
↓
W1 : 2 - 3 W15 : 2 - 3↲
W2 : 1 - 10 W16 : 1 - 2↲
W3 : 2 - 3 W17 : 2 - 3↲
W4 : 2 - 3 W18 : 1 - 2↲
W5 : No jumper W19 : 1 - 2↲
W6 : No jumper W20 : 2 - 3↲
W7 : 2 - 3 W21 : 1 - 2↲
W8 : 1 - 2 W22 : 2 - 3↲
W9 : No jumper W23 : 1 - 2↲
W10 : 1 - 2 W24 : 2 - 3↲
W11 : 1 - 2 W25 : 1 - 2↲
W12 : 2 - 3 W26 : 1 - 2↲
W13 : 2 - 3 W27 : 2 - 3↲
W14 : 2 - 3 W28 : No jumper↲
↲
↲
Table 6.4 ┆84┆Standard jumper configuration on the F64X ↓
┆19┆┆94┆┄┄communication board.↲
↲
┆a1┆ Removed jumpers New jumpers ↲
! ! !↲
! W24 : 2 - 3 ! W24 : 1 - 2 !↲
! W26 : 1 - 2 ! W26 : 2 - 3 !↲
┆a1┆! ! !↲
↲
Table 6.5 ┆84┆Jumper modification of the F64X if it is used ↓
┆19┆┆94┆┄┄as the second communication board. Note that ↓
┆19┆┆94┆┄┄when the ETC611 includes a memory expansion ↓
┆19┆┆94┆┄┄MEX611 (1/2 Mbyte) modul. Then the ETC611 must ↓
┆19┆┆94┆┄┄be modificated (See ref 8).↲
↲
↲
┆a1┆ Removed jumpers New jumpers ↲
! ST4 : 4 - 9 ! ST26: 3 - 4 !↲
! ST23: 4 - 7 ! ST 4: 6 - 7 !↲
! ST26: 1 - 6 ! !↲
┆a1┆! ! !↲
↲
Table 6.6 ┆84┆Jumper modification of the ETC611 with memory ↓
┆19┆┆94┆┄┄exporsion MEX611 (1/2 Mbyte) and one ↓
┆19┆┆94┆┄┄intelligent communication board F64X.↲
↲
════════════════════════════════════════════════════════════════════════
↓
┆a1┆ Removed jumpers New jumpers ↲
! ST4 : 4 - 9 ! !↲
! ST23 : 4 - 7 ! !↲
! ST23 : 5 - 6 ! ST26 : 2 - 5 !↲
! ST26 : 1 - 6 ! ST 4 : 5 - 8 !↲
┆a1┆! ! !↲
↲
Table 6.7 ┆84┆Jumper modification of the ETC611 with memory ↓
┆19┆┆94┆┄┄expansion MEX611 (1/2 Mbyte) and two ↓
┆19┆┆94┆┄┄intelligent communication board F64X.↲
↲
↲
┆a1┆┆b0┆7. INSTALLATION↲
↲
1. Turn off power.↲
↲
2. Remove the right side of the cover.↲
↲
3a. Modify the jumpers.↲
3b. ┆84┆Check that ROC448 (COM601) or ROC449 (COM602) is ↓
┆19┆┆8d┆┄┄placed in position two.↲
↲
4. ┆84┆Place the F64X in slot two if it is the first ↓
┆19┆┆8d┆┄┄communication board, else in slot three.↲
↲
5. Connect circuit 1 from J2 on F64X to KBL687↲
↲
6. If it is the first F64X then :↲
↲
┆84┆Connect KBL719 from J3 on F64X to J11 on the ↓
┆19┆┆8d┆┄┄backpanel and connect another KBL719 from J4 on F64X ↓
┆19┆┆8d┆┄┄to J12 on the backplane.↲
↲
Else :↲
↲
┆84┆Connect KBL719 from J3 on F64X to J13 on the ↓
┆19┆┆8d┆┄┄backpanel and connect another KBL719 from J4 on F64X ↓
┆19┆┆8d┆┄┄to J14 on the backplane.↲
↲
7. Connect KBL727 from J5 on F64X to J2 on LED603.↲
↲
┆8c┆┆83┆┆ec┆↓
8. Remove the back cover.↲
↲
9. Place the label at the J11-J14 connectors.↲
↲
10. ┆84┆Connect a terminal to J41 on the backplane.↲
↲
11. ┆84┆┆84┆┆84┆Turn on the power and Test the F61X from the CPU691 ↓
┆19┆┆8d┆┄┄(See ref. 10).↲
↲
12. ┆84┆If the tests succeded, then place the back ↓
┆19┆┆8d┆┄┄and right side cover on the computer. Disconnect the ↓
┆19┆┆8d┆┄┄terminal from J41.↲
↲
13. ┆84┆Now the hardware installation is finished. Continue ↓
┆19┆┆8d┆┄┄with software installation if necessary. (See ref. ↓
┆19┆┆8d┆┄┄9).↲
════════════════════════════════════════════════════════════════════════
↓
┆b0┆┆a1┆┆f0┆┆e1┆┆b0┆┆a1┆APPENDIX:↲
↲
┆b0┆┆a1┆A. REFERENCES┆b0┆↲
↲
1. ┆84┆RC3902 Processor Unit, General information. RCSL 99-1 ↓
┆19┆┆8d┆┄┄10056.↲
↲
2. ┆84┆ETC601/611 Hardware Reference Manual. RCSL 99-0 ↓
┆19┆┆8d┆┄┄00772.↲
↲
3. ┆84┆MSI601 Hardware Reference Manual. RCSL 99-0 00774.↲
↲
4. ┆84┆MEX601/611 Hardware Reference Manual. RCSL 99-0 ↓
┆19┆┆8d┆┄┄00773.↲
↲
5. ┆84┆ETC601 Hardware Selftest Manual Version 1.0. RCSL 99-↓
┆19┆┆8d┆┄┄1 09944.↲
↲
6. ┆84┆F641/F642 Communication Adapter. Hardware ↓
┆19┆┆8d┆┄┄installation. RCSL 99-1 10059.↲
↲
7. COM601. Hardware Reference Manual. RCSL 44-RT2121.↲
↲
8. ┆84┆RC3931 Communication Processor. HW installation. ↓
┆19┆┆8d┆┄┄RCSL99-1 10058↲
↲
9. ┆84┆RC3931 Communication Processor. Users Guide. RCSL99-1 ↓
┆19┆┆8d┆┄┄10073.↲
↲
10. RC39 Selftest concept. RCSL 99-1 10092.↲
↲
11. F641 COM601 HW Seftest. RCSL 99-1 10097.↲
↲
12. ┆84┆RC3902 Selftest (incl MEM board). Reference Manual. ↓
┆19┆┆8d┆┄┄RCSL 99-1 10094.↲
┆1a┆┆1a┆det med det rigtige navn og så ↓
trykke <RETUR>. Hvis Uniplex har indsat det rigtige opgavenavn p