|
DataMuseum.dkPresents historical artifacts from the history of: RC4000/8000/9000 |
This is an automatic "excavation" of a thematic subset of
See our Wiki for more about RC4000/8000/9000 Excavated with: AutoArchaeologist - Free & Open Source Software. |
top - metrics - download
Length: 59548 (0xe89c)
Types: TextFile
Names: »MENU.TXT«
└─⟦6b0c384a4⟧ Bits:30004163 SW9890I RC9000-10 Monitor Rel. 83.2
└─⟦this⟧ »MENU.TXT«
/* @(#)MENU.TXT 1.39 (RC International) 1/4/93 */\r /* @(#)Text for the menus on the SSP */\r /* Menu commands are defined in mnhsys.ext, */\r /* which defines the command number areas. */\r \r cdefault "Select function ==> "\r cmenu CMN_MAIN 4 "S S P M A I N M E N U"\r hline h cmenu 1 "Healthiness monitoring"\r line l menucmd 1 "Log utilities"\r line c menucmd 4 "Customization utilities"\r line d cmenu 4 "Display utilities"\r line t menucmd 2 "Test and load utilities"\r hline q cmenu 21 "Commands for special test"\r line e menucmd 3 "Exchange diskette"\r cmenu CMN_HEAL 0 "H E A L T H I N E S S M O N I T O R I N G"\r line t menucmd 11 "Temperature monitoring"\r line p menucmd 12 "Power supply monitoring"\r line m menucmd 13 "Module monitoring for one slot"\r line a menucmd 14 "Module monitoring for all slots"\r cmenu CMN_LOG 0 "L O G U T I L I T I E S"\r line l menucmd 21 "List logfile"\r line s menucmd 22 "Start logging on diskette"\r line e menucmd 23 "End logging on diskette"\r line h menucmd 24 "Hardcopy of log wanted"\r line n menucmd 25 "No hardcopy of log wanted"\r line p menucmd 26 "Set log parameters"\r cmenu CMN_CONF 0 "C U S T O M I Z A T I O N U T I L I T I E S"\r line p menucmd 31 "Set PU name"\r hline m menucmd 32 "Module customization"\r hline s menucmd 179 "SCSI controller customization"\r line a menucmd 37 "Set module customization to actual configuration"\r line e menucmd 40 "Set serial number used for ethernet address calculations"\r line o menucmd 38 "Modem customization"\r eline\r line 1 cmenu 43 "Parameters for model 10"\r line 3 cmenu 45 "Parameters for model TX"\r eline\r line r menucmd 35 "Read customization data from diskette"\r line d menucmd 39 "Read another PU's customization data from diskette"\r line w menucmd 36 "Write customization data to diskette"\r eline\r line c menucmd 33 "Real time clock"\r line t menucmd 34 "Timezone and daylight saving"\r cmenu CMN_DISP 0 "D I S P L A Y U T I L I T I E S"\r line m menucmd 61 "Display module status"\r line t menucmd 62 "Display test messages for one slot"\r line a menucmd 225 "Display all test messages"\r line c menucmd 64 "Clear all test messages"\r cmenu CMN_TL_PD 2 "T E S T A N D L O A D U T I L I T I E S"\r line T menucmd 41 "PU power-up and enter manual PU test"\r line L menucmd 42 "PU power-up and enter manual PU load"\r line O menucmd 43 "PU power-up and enter operating state"\r line E menucmd 44 "PU power-up and enter error handling state"\r hline P menucmd 45 "PU power-down"\r hline A menucmd 46 "PU power-up for power adjustment"\r eline\r line b menucmd 146 "Boot new SSP program from diskette"\r cmenu CMN_TL_EH 7 "T E S T A N D L O A D U T I L I T I E S"\r line 1 menucmd 55 "Dump global memory on disk"\r line 2 menucmd 56 "Dump global memory on diskette"\r line 3 menucmd 57 "Dump controller memory on diskette"\r eline\r line A menucmd 58 "Change parameter for global memory dump on diskette"\r line B menucmd 59 "Change parameter for controller memory dump on diskette"\r eline\r line T menucmd 41 "Enter manual PU test"\r line L menucmd 42 "Enter manual PU load"\r line O menucmd 43 "Enter operating state"\r line E menucmd 44 "Stay in error handling state"\r line P menucmd 45 "PU power-down"\r cmenu CMN_TL_AT 0 "T E S T A N D L O A D U T I L I T I E S"\r line M menucmd 41 "Enter manual PU test"\r line E menucmd 44 "Enter error handling state"\r line P menucmd 45 "PU power-down"\r cmenu CMN_TL_MT 0 "T E S T A N D L O A D U T I L I T I E S"\r hline S menucmd 48 "SSP test"\r eline\r hline R menucmd 77 "Read module identifications"\r eline\r hline B menucmd 47 "SSP based module test"\r hline G cmenu 12 "Global memory test"\r hline M menucmd 49 "Module based test"\r hline c menucmd 50 "Re-configure memory"\r eline\r line L menucmd 42 "Enter manual PU load"\r line O menucmd 43 "Enter operating state"\r line e menucmd 44 "Enter error handling state"\r line P menucmd 45 "PU power-down"\r cmenu CMN_TL_ML 0 "T E S T A N D L O A D U T I L I T I E S"\r hline C menucmd 131 "Configure memory"\r eline\r hline M menucmd 122 "Load module"\r hline G menucmd 123 "Load global memory"\r eline\r hline I menucmd 134 "Initialize global memory"\r eline\r hline V menucmd 135 "Start virtual terminals and other SSP services"\r hline R menucmd 136 "Release controllers"\r hline S menucmd 137 "Start main processors and enter operating state"\r eline\r line O menucmd 43 "Enter operating state"\r line E menucmd 44 "Enter error handling state"\r line P menucmd 45 "PU power-down"\r cmenu CMN_TL_REST 0 "T E S T A N D L O A D U T I L I T I E S"\r line E menucmd 44 "Enter error handling state"\r line P menucmd 45 "PU power-down"\r cmenu CMN_SSP_TST 0 "S S P T E S T"\r line 0 menucmd 71 "SSP system bus FIFO test"\r line 1 menucmd 72 "SSP slave interface test"\r line 2 menucmd 73 "SSP interrupt FIFO test"\r line 3 menucmd 74 "Backplane test"\r line 4 menucmd 76 "Lamp and switch test"\r eline\r line N menucmd 95 "Execute normal startup sequence"\r eline\r line C menucmd 93 "Send CONTINUE to local test administrator"\r line S menucmd 94 "Send STOP to local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters"\r cmenu CMN_GMTST 0 "G L O B A L M E M O R Y T E S T"\r line C menucmd 75 "Configure memory"\r eline\r line 0 menucmd 2561 "SSP based global memory test"\r line 1 menucmd 2562 "SSP based write memory test"\r line 2 menucmd 2563 "SSP based read memory test"\r line 3 menucmd 2564 "CPU based global memory test"\r eline\r line A menucmd 2818 "Change parameters for SSP based test (0-2)"\r line B menucmd 2819 "Change parameters for CPU based global memory test"\r eline\r line S menucmd 94 "Send STOP to SSP local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters for SSP"\r cmenu CMN_SSP_MEMTST 0 "S S P B A S E D M E M O R Y M O D U L E T E S T"\r line 0 menucmd 81 "Functionality test"\r line 1 menucmd 80 "ECC Check test"\r line 2 menucmd 79 "Semaphore test"\r eline\r line N menucmd 95 "Execute normal startup sequence"\r line E menucmd 96 "Execute extended test sequence"\r eline\r line C menucmd 93 "Send CONTINUE to local test administrator"\r line S menucmd 94 "Send STOP to local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters"\r cmenu CMN_SSP_CNTLTST 0 "S S P B A S E D C O N T R O L L E R T E S T"\r line 0 menucmd 82 "Functionality test"\r line 1 menucmd 83 "EPROM test"\r line 2 menucmd 84 "RAM test"\r eline\r line 3 menucmd 85 "Interrupt FIFO test"\r line 4 menucmd 86 "System bus FIFO test"\r eline\r line N menucmd 95 "Execute normal startup sequence"\r line E menucmd 96 "Execute extended test sequence"\r eline\r line C menucmd 93 "Send CONTINUE to local test administrator"\r line S menucmd 94 "Send STOP to local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters"\r cmenu CMN_SSP_CPU9TST 0 "S S P B A S E D R I S C P R O C E S S O R T E S T"\r line 0 menucmd 87 "Functionality test"\r line 1 menucmd 88 "RAM test"\r eline\r line 2 menucmd 89 "Interrupt FIFO test (not CPU901)"\r eline\r line N menucmd 95 "Execute normal startup sequence"\r line E menucmd 96 "Execute extended test sequence"\r eline\r line C menucmd 93 "Send CONTINUE to local test administrator"\r line S menucmd 94 "Send STOP to local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters"\r cmenu CMN_CPU901_TST 0 "R I S C P R O C E S S O R T E S T"\r line L menucmd 51 "Load test program into on-module memory"\r line G menucmd 52 "Load test program into global memory"\r eline\r line D cmenu 23 "Default tests"\r line E cmenu 24 "Extended tests"\r line P cmenu 25 "Separate tests"\r line Q cmenu 26 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_CPU985_TST 0 "R C C P U T E S T"\r line L menucmd 51 "Load microcode"\r line G menucmd 52 "Load test program into global memory"\r eline\r line D cmenu 27 "Default tests"\r line E cmenu 28 "Extended tests"\r line P cmenu 29 "Separate tests"\r line Q cmenu 30 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_IOC901_TST 0 "I P I I O C T E S T"\r line L menucmd 51 "Load test program"\r eline\r line D cmenu 31 "Default tests"\r line E cmenu 32 "Extended tests"\r line P cmenu 33 "Separate tests"\r line Q cmenu 34 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_DLC901_TST 0 "D L C T E S T"\r line L menucmd 51 "Load test program"\r eline\r line D cmenu 35 "Default tests"\r line E cmenu 36 "Extended tests"\r line P cmenu 37 "Separate tests"\r line Q cmenu 38 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_SSP901_TST 0 "S S P T E S T"\r line L menucmd 51 "Load test program"\r eline\r line D cmenu 39 "Default tests"\r line E cmenu 40 "Extended tests"\r line P cmenu 41 "Separate tests"\r line Q cmenu 42 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_SPCTST 0 "**** S P E C I A L T E S T M E N U ****"\r line a menucmd 141 "Assume PU tested"\r line i menucmd 142 "Set ignore"\r line r menucmd 143 "Reset and release system bus"\r line 0 menucmd 144 "Set special customization values"\r line 1 menucmd 161 "Set number of couplings for SSP"\r line 2 menucmd 162 "Set number of couplings for RISC CPU"\r line 3 menucmd 163 "Set number of couplings for RC CPU"\r line b menucmd 146 "Boot new SSP program from diskette"\r line x menucmd 147 "Exclude modules"\r line p menucmd 148 "Debug PI-4 kernel on other modules"\r line m cmenu 44 "Debug RC monitor"\r line s menucmd 149 "Start snoop on system bus"\r line f cmenu 47 "Set file names for load"\r cmenu CMN_PI4DEB 0 "P I - 4 D E B U G"\r line n menucmd 512 "Send NMI to controller"\r line d menucmd 513 "Display PI-4 error value"\r line r menucmd 514 "Restart PI-4 kernel"\r cmenu CMN_CPU901_DLT 0 "R I S C C P U L O C A L D E F A U L T T E S T S"\r line 0 menucmd 1024 "Instruction cache data test" /* first test number */\r line 1 menucmd 1025 "Instruction cache tag test" /* 16 numbers reserved */\r line 2 menucmd 1026 "Instruction cache parity test"\r line 3 menucmd 1027 "Instruction cache function test"\r line 4 menucmd 1028 "Data cache data test"\r line 5 menucmd 1029 "Data cache tag test"\r line 6 menucmd 1030 "Data cache parity test"\r line 7 menucmd 1031 "Data cache function test"\r line 8 menucmd 1032 "Write buffer test"\r line 9 menucmd 1033 "Data cache invalidation test"\r line A menucmd 1034 "Floating point chip test"\r line B menucmd 1035 "Timer test"\r line C menucmd 1036 "Global memory default test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU901_ELT 0 "R I S C C P U L O C A L E X T E N D E D T E S T S"\r line 0 menucmd 1040 "Cache driver test" /* 16 numbers reserved */\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU901_SLT 0 "R I S C C P U L O C A L S E P A R A T E T E S T S"\r line 0 menucmd 1056 "Global memory test" /* 16 numbers reserved */\r line 1 menucmd 1057 "Wait function test"\r eline\r line A menucmd 2052 "Change parameters for global memory test"\r line B menucmd 2054 "Change parameters for wait test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU901_QLT 0 "R I S C C P U L O C A L S E Q U E N C E T E S T S"\r line 0 menucmd 1072 "Normal start up sequence" /* 16 numbers reserved */\r line 1 menucmd 1073 "Extended test sequence"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU985_DLT 0 "R C C P U L O C A L D E F A U L T T E S T S"\r line 0 menucmd 1088 "Instruction test" /* first test number + 64 */\r line 1 menucmd 1089 "Floating point instruction test"/* 16 numbers reserved */\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU985_ELT 0 "R C C P U L O C A L E X T E N D E D T E S T S"\r line 0 menucmd 1104 "Snoop test" /* 16 numbers reserved */\r line 1 menucmd 1105 "Interrupt test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU985_SLT 0 "R C C P U L O C A L S E P A R A T E T E S T S"\r line 0 menucmd 1120 "Global memory test" /* 16 numbers reserved */\r line 1 menucmd 1121 "Data cache test"\r eline\r line A menucmd 2053 "Change parameters for global memory test"\r line B menucmd 2055 "Change parameters for data cache test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CPU985_QLT 0 "R C C P U L O C A L S E Q U E N C E T E S T S"\r line 0 menucmd 1136 "Normal start up sequence"/* 16 numbers reserved */\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC901_DLT 0 "I P I I O C L O C A L D E F A U L T T E S T S"\r line 0 menucmd 1152 "Local RAM test"\r line 1 menucmd 1153 "Timer test"\r line 2 menucmd 1154 "System bus interface test"\r line 3 menucmd 1155 "Slave interface test"\r line 4 menucmd 1156 "Global memory access test 1"\r line 5 menucmd 1157 "Tridirectional FIFO test"\r line 6 menucmd 1158 "DMA system bus interface test"\r line 7 menucmd 1159 "DMA global memory access test 1"\r line 8 menucmd 1160 "IPI interface test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC901_ELT 0 "I P I I O C L O C A L E X T E N D E D T E S T S"\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC901_SLT 0 "I P I I O C L O C A L S E P A R A T E T E S T S"\r line 0 menucmd 1184 "Global memory access test 2"\r line 1 menucmd 1185 "DMA global memory access test 2"\r line 2 menucmd 1186 "Write memory pattern"\r line 3 menucmd 1187 "Read memory pattern"\r line 4 menucmd 1188 "DMA write memory pattern"\r line 5 menucmd 1189 "DMA read memory pattern"\r line 6 menucmd 1190 "IPI communication test (old format)"\r line 7 menucmd 1191 "IPI load test (old format)"\r line 8 menucmd 1192 "IPI communication test"\r line 9 menucmd 1193 "IPI load test"\r eline\r line A menucmd 2049 "Change parameters for global memory test (0-5)"\r line B menucmd 2057 "Change parameters for IPI communication test (6, 8)"\r line C menucmd 2056 "Change parameters for IPI load test (7, 9)"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC901_QLT 0 "I P I I O C L O C A L S E Q U E N C E T E S T S"\r line 0 menucmd 1200 "Normal start up sequence"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLC901_DLT 0 "D L C L O C A L D E F A U L T T E S T S"\r line 0 menucmd 1216 "Local RAM test"\r line 1 menucmd 1217 "Timer test"\r line 2 menucmd 1218 "System bus interface test"\r line 3 menucmd 1219 "Slave interface test"\r line 4 menucmd 1220 "Global memory access test 1"\r line 5 menucmd 1221 "LAN buffers test"\r line 6 menucmd 1222 "LAN controller 1 test"\r line 7 menucmd 1223 "LAN controller 2 test"\r line 8 menucmd 1224 "DMA system bus interface test"\r line 9 menucmd 1225 "DMA global memory access test 1"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLC901_ELT 0 "D L C L O C A L E X T E N D E D T E S T S"\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLC901_SLT 0 "D L C L O C A L S E P A R A T E T E S T S"\r line 0 menucmd 1248 "Write memory pattern"\r line 1 menucmd 1249 "Read memory pattern"\r line 2 menucmd 1250 "Global memory access test 2"\r line 3 menucmd 1251 "DMA global memory access test 2"\r line 4 menucmd 1252 "LAN external loop-back test"\r line 5 menucmd 1253 "LAN cable test"\r line 6 menucmd 1254 "LAN to LAN test"\r eline\r line A menucmd 2049 "Change parameters for global memory test (0-2)"\r line B menucmd 2050 "Change parameters for global memory test (3)"\r line C menucmd 2051 "Change parameters for LAN test (4-6)"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLC901_QLT 0 "D L C L O C A L S E Q U E N C E T E S T S"\r line 0 menucmd 1264 "Normal start up sequence"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_SSP901_DLT 0 "S S P L O C A L D E F A U L T T E S T S"\r line 0 menucmd 1280 "Local RAM test"\r line 1 menucmd 1281 "Timer test"\r line 2 menucmd 1282 "Real time clock test"\r line 3 menucmd 1283 "LAN interface test"\r line 4 menucmd 1284 "System bus interface test"\r line 5 menucmd 1285 "Slave interface test"\r line 6 menucmd 1286 "Global memory access test 1"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_SSP901_ELT 0 "S S P L O C A L E X T E N D E D T E S T S"\r line 0 menucmd 1296 "LAN cable test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_SSP901_SLT 0 "S S P L O C A L S E P A R A T E T E S T S"\r line 0 menucmd 1312 "Global memory access test 2"\r line 1 menucmd 1313 "Write memory pattern"\r line 2 menucmd 1314 "Read memory pattern"\r eline\r line A menucmd 2049 "Change parameters for global memory test (0-2)"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_SSP901_QLT 0 "S S P L O C A L S E Q U E N C E T E S T S"\r line 0 menucmd 1328 "Normal start up sequence"\r line 1 menucmd 1329 "Extended test sequence"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_CONF_10 0 "P A R A M E T E R S F O R M O D E L 1 0"\r line b menucmd 150 "Basic system parameters"\r hline x menucmd 160 "Extra system parameters"\r line m menucmd 159 "Memory usage"\r eline \r hline c menucmd 151 "Controller customization"\r eline\r line 1 menucmd 152 "Parameters for LAN controller no. 1"\r eline\r line 2 menucmd 153 "Parameters for LAN controller no. 2"\r eline\r line 3 menucmd 154 "Parameters for LAN controller no. 3"\r eline\r line 4 menucmd 155 "Parameters for LAN controller no. 4"\r cmenu CMN_OSDEB 0 "D E B U G G I N G R C M O N I T O R"\r line h menucmd 520 "Halt RC clock"\r line s menucmd 521 "Start RC clock"\r cmenu CMN_CONF_30 0 "P A R A M E T E R S F O R M O D E L T X"\r line b menucmd 170 "Basic system parameters"\r line c menucmd 171 "Capability parameters"\r hline s menucmd 172 "I/O system parameters"\r hline i menucmd 173 "I/O controller customization"\r hline l menucmd 174 "LAN and SIB controller customization"\r line 0 menucmd 175 "Parameters for LAN controller no. 0"\r line 1 menucmd 176 "Parameters for LAN controller no. 1"\r line 2 menucmd 177 "Parameters for LAN controller no. 2"\r line 3 menucmd 178 "Parameters for LAN controller no. 3"\r cmenu CMN_RCLAN 0 "M O D E L 1 0 L A N P A R A M E T E R S"\r line D menucmd 190 "Device handler parameters"\r line I menucmd 191 "IMC parameters"\r hline X menucmd 192 "Extra parameters"\r cmenu CMN_LFNAME 0 "S E T F I L E N A M E S F O R L O A D"\r line 1 menucmd 530 "Test program file names for model 10"\r line 2 menucmd 531 "Test program file names for model TX"\r line 3 menucmd 532 "Operating program file names for model 10"\r line 4 menucmd 533 "Operating program file names for model TX"\r cmenu CMN_TL_OPER 0 "T E S T A N D L O A D U T I L I T I E S"\r line R menucmd 53 "Controller software reset"\r hline A menucmd 54 "Controller software abort"\r eline\r hline E menucmd 44 "Enter error handling state"\r hline P menucmd 45 "PU power-down"\r cmenu CMN_SSP_CPU8TST 0 "S S P B A S E D R C P R O C E S S O R T E S T"\r line 0 menucmd 87 "Functionality test"\r eline\r line C menucmd 93 "Send CONTINUE to local test administrator"\r line S menucmd 94 "Send STOP to local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters"\r cmenu CMN_IOC911_TST 0 "S C S I I O C T E S T"\r line L menucmd 51 "Load test program"\r eline\r line D cmenu 51 "Default tests"\r line E cmenu 52 "Extended tests"\r line P cmenu 53 "Separate tests"\r line Q cmenu 54 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_IOC911_DLT 0 "S C S I I O C L O C A L D E F A U L T T E S T S"\r line 0 menucmd 1344 "Local RAM test" /* 16 numbers reserved */\r line 1 menucmd 1345 "Timer test"\r line 2 menucmd 1346 "System bus interface test"\r line 3 menucmd 1347 "Slave interface test"\r line 4 menucmd 1348 "Global memory access test 1"\r line 5 menucmd 1349 "Tridirectional FIFO test"\r line 6 menucmd 1350 "DMA system bus interface test"\r line 7 menucmd 1351 "DMA global memory access test 1"\r line 8 menucmd 1352 "SCSI Controller test"\r line 9 menucmd 1353 "SCSI DMA test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC911_ELT 0 "S C S I I O C L O C A L E X T E N D E D T E S T S"\r eline /* 16 numbers reserved */\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC911_SLT 0 "S C S I I O C L O C A L S E P A R A T E T E S T S"\r line 0 menucmd 1376 "Global memory access test 2" /* 16 numbers reserved */\r line 1 menucmd 1377 "DMA global memory access test 2"\r line 2 menucmd 1378 "Write memory pattern"\r line 3 menucmd 1379 "Read memory pattern"\r line 4 menucmd 1380 "DMA write memory pattern"\r line 5 menucmd 1381 "DMA read memory pattern"\r line 6 menucmd 1382 "SCSI tape test"\r line 7 menucmd 1383 "SCSI disk test"\r line 8 menucmd 1384 "SCSI format test"\r eline\r line A menucmd 2049 "Change parameters for global memory test (0-5)"\r line B menucmd 2058 "Change parameters for scsi tape test"\r line C menucmd 2059 "Change parameters for scsi disk test"\r line D menucmd 2060 "Change parameters for scsi format test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_IOC911_QLT 0 "S C S I I O C L O C A L S E Q U E N C E T E S T S"\r line 0 menucmd 1392 "Normal start up sequence" /* 16 numbers reserved */\r line 1 menucmd 1393 "Extended test sequence"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLU901_TST 2 "D L U T E S T"\r line B cmenu 60 "Special Tests"\r eline\r line D cmenu 56 "Default tests"\r line E cmenu 57 "Extended tests"\r line P cmenu 58 "Separate tests"\r line Q cmenu 59 "Sequence tests"\r eline\r line U menucmd 2560 "Execute unknown test"\r line A menucmd 2048 "Change parameter for unknown separate test"\r line X menucmd 2817 "Change primary test parameter for unknown test"\r eline\r line C menucmd 91 "Send CONTINUE to local test administrator"\r line S menucmd 92 "Send STOP to local test administrator"\r eline\r line M menucmd 227 "Display test messages"\r cmenu CMN_DLU901_DLT 0 "D L U D E F A U L T T E S T S"\r line 0 menucmd 1408 "Channel A fifos test" /* 16 numbers reserved */\r line 1 menucmd 1409 "Channel B fifos test"\r line 2 menucmd 1410 "Channel A receiver test"\r line 3 menucmd 1411 "Channel B receiver test"\r line 4 menucmd 1412 "Channel A internal loop back test"\r line 5 menucmd 1413 "Channel B internal loop back test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLU901_ELT 0 "D L U E X T E N D E D T E S T S"\r line 0 menucmd 1424 "Channel A external Loop back test"/*16 numbers reserved*/\r line 1 menucmd 1425 "Channel B external Loop back test"\r line 2 menucmd 1426 "Concurrent A/B external loop back test"\r eline \r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLU901_SLT 0 "D L U S E P A R A T E T E S T S"\r line 0 menucmd 1440 "Concurrent channel test"/* 16 numbers reserved */\r eline\r line A menucmd 2061 "Change parameters for concurrent channels test"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_DLU901_QLT 0 "D L U S E Q U E N C E T E S T S"\r line 0 menucmd 1456 "Normal start up sequence" /* 16 numbers reserved */\r line 1 menucmd 1457 "Extended test sequence"\r eline\r line x menucmd 2816 "Change primary test parameters"\r cmenu CMN_SSP_DLUTST 0 "S S P B A S E D D L U M O D U L E T E S T" \r line 0 menucmd 90 "Functionality test"\r eline\r line C menucmd 93 "Send CONTINUE to local test administrator"\r line S menucmd 94 "Send STOP to local test administrator"\r eline\r line X menucmd 2820 "Change primary test parameters"\r fmenu FMN_SETPCNF 0 201 "S E T P U N A M E"\r line 0 0 string 10 "PU name"\r fmenu FMN_SETMCNF 0 202 "M O D U L E C U S T O M I Z A T I O N"\r line 1 255 modules 7 "Slot 0"\r line 1 255 modules 7 "Slot 1"\r line 1 255 modules 7 "Slot 2"\r line 1 255 modules 7 "Slot 3"\r line 1 255 modules 7 "Slot 4"\r line 1 255 modules 7 "Slot 5"\r line 1 255 modules 7 "Slot 6"\r line 1 255 modules 7 "Slot 7"\r line 1 255 modules 7 "Slot 8"\r line 1 255 modules 7 "Slot 9"\r line 1 255 modules 7 "Slot 10"\r line 1 255 modules 7 "Slot 11"\r line 1 255 modules 7 "Slot 12"\r line 1 255 modules 7 "Slot 13"\r line 1 255 modules 7 "Slot 14"\r line 1 255 modules 7 "Slot 15"\r fmenu FMN_SETRTC 0 203 "S E T R E A L T I M E C L O C K"\r line 1968 2067 decimal 4 "Year"\r line 1 12 months 3 "Month"\r line 1 31 decimal 2 "Date"\r line 0 23 decimal 2 "Hour"\r line 0 59 decimal 2 "Minute"\r line 0 59 decimal 2 "Second"\r fmenu FMN_SETZONE 0 204 "S E T T I M E Z O N E A N D D A Y L I G H T S A V I N G"\r line -720 720 signed 4 "Timezone"\r line 1 2 yesno 3 "Daylight saving"\r line 0 10 decimal 2 "Daylight saving type"\r fmenu FMN_SETRC 0 205 "M O D E L 1 0 B A S I S S Y S T E M P A R A M E T E R S"\r line 1 92 decimal 2 "Number of internal processes"\r line 20 1951 decimal 4 "Number of external processes"\r line 4 2047 decimal 4 "Number of areas"\r line 7 2047 decimal 4 "Number of message buffers"\r line 1 32 decimal 2 "Number of chain tables"\r line 0 1000 decimal 4 "Number of s terminal descriptors"\r eline " "\r line 0 3000 decimal 4 "Device number for BOOT disk"\r line 0 7 decimal 1 "Slave address of BOOT DCM"\r line 0 3 decimal 1 "Facility address of BOOT disk"\r eline " "\r line 1 10 decimal 2 "Length of SSP time slice in units of 20 ms"\r fmenu FMN_SETRCCNTL 0 206 "M O D E L 1 0 C O N T R O L L E R C U S T O M I Z A T I O N"\r line 20 35 decimal 2 "SSP is called sspmain on device number"\r line 0 15 decimal 2 "IOC no. 1 slot number"\r line 20 35 decimal 2 "called iocmain1 on device number"\r line 0 15 decimal 2 "IOC no. 2 slot number"\r line 20 35 decimal 2 "called iocmain2 on device number"\r line 0 15 decimal 2 "IOC no. 3 slot number"\r line 20 35 decimal 2 "called iocmain3 on device number"\r line 0 15 decimal 2 "IOC no. 4 slot number"\r line 20 35 decimal 2 "called iocmain4 on device number"\r line 0 15 decimal 2 "DLC no. 1 slot number"\r line 20 35 decimal 2 "called lanmain1 on device number"\r line 0 15 decimal 2 "DLC no. 2 slot number"\r line 20 35 decimal 2 "called lanmain2 on device number"\r line 0 15 decimal 2 "DLC no. 3 slot number"\r line 20 35 decimal 2 "called lanmain3 on device number"\r line 0 15 decimal 2 "DLC no. 4 slot number"\r line 20 35 decimal 2 "called lanmain4 on device number"\r fmenu FMN_SET_RCLAN 0 207 "MODEL 10 LAN DEVICE HANDLER PARAMETERS"\r line 0 65535 string 8 "Host name"\r eline " "\r line 0 200 decimal 3 "Number of CSP terminal handlers"\r line 0 200 decimal 3 "Number of CSP consoles"\r line 0 400 decimal 3 "Number of shared CSP buffers"\r line 0 127 decimal 3 "Interrupt character for CSP terminals"\r line 0 20 decimal 2 "Number of CSP printers"\r line 1 600 decimal 3 "CSP printer deselect timeout (seconds)"\r line 0 50 decimal 2 "Number of 3270 device handler pairs"\r line 0 100 decimal 3 "Number of 3270 CUs (CU00, CU01, etc.)"\r line 10 120 decimal 3 "3270 input timeout (seconds)"\r fmenu FMN_SET_RCLANX 0 208 "MODEL 10 LAN CONTROLLER EXTRA PARAMETERS"\r line 3 10 decimal 2 "Number of 3270 receive buffers/device handlers"\r line 128 3861 rclanv 4 "Size of 3270 receive buffers or VER3"\r line 512 3860 decimal 4 "Size of 3270 transmit buffers"\r line 129 4097 decimal 4 "Size of CSPT transmit buffers"\r line 129 1025 decimal 4 "Size of CSPT receive buffers"\r line 129 4097 decimal 4 "Size of CSPP transmit buffers"\r eline " "\r line 0 65535 hex 4 "Test mask"\r line 1 2 decimal 1 "Hardware LAN port used"\r fmenu FMN_SETMPS 0 209 "M O D E L T X B A S I C S Y S T E M P A R A M E T E R S"\r line 1 63 decimal 2 "Logical network number (on SIB)"\r line 1 63 decimal 2 "Logical PU-number (on SIB)"\r fmenu FMN_DSPLOG 0 210 "D I S P L A Y S S P L O G"\r line 1 2 logno 8 "Log"\r line 1 12 procs 4 "Process name"\r line 1 4 loglevel 11 "Severity level"\r fmenu FMN_TPMON 0 211 "T E M P E R A T U R E M O N I T O R I N G"\r line 0 600 decimal 3 "Temperature monitoring interval (in 100 ms)"\r eline " "\r line 1 65500 decimal 5 "Temperature warning repeat frequency"\r line 0 65500 decimal 5 "Temperature log frequency"\r eline " "\r line 1 2 yesno 3 "Activate left PU temperature indicator"\r line 1 2 yesno 3 "Activate centre PU temperature indicator"\r line 1 2 yesno 3 "Activate right PU temperature indicator"\r line 1 2 yesno 3 "Activate left PS temperature indicator"\r line 1 2 yesno 3 "Activate centre PS temperature indicator"\r line 1 2 yesno 3 "Activate right PS temperature indicator"\r fmenu FMN_PSMON 0 212 "P O W E R S U P P L Y M O N I T O R I N G"\r line 0 600 decimal 3 "Power supply monitoring interval (in 100 ms)"\r line 1 65500 decimal 5 "Power warning repeat frequency"\r line 0 65500 decimal 5 "Power supply log frequency"\r eline " "\r line 0 4 decimal 1 "Number of power supplies needed"\r fmenu FMN_MODIMON 0 213 "C O N T R O L L E R M O N I T O R I N G"\r line 0 600 decimal 3 "Module status read interval (in 100 ms)"\r eline " "\r line 0 65500 decimal 5 "Module hardware monitoring frequency"\r line 0 65500 decimal 5 "Module watchdog monitoring frequency"\r line 0 65500 decimal 5 "Module status log frequency"\r fmenu FMN_MODCMON 0 214 "C P U M O N I T O R I N G"\r line 0 600 decimal 3 "Module status read interval (in 100 ms)"\r eline " "\r line 0 65500 decimal 5 "Module hardware monitoring frequency"\r line 0 65500 decimal 5 "Module status log frequency"\r fmenu FMN_MODMMON 0 215 "M E M O R Y M O D U L E M O N I T O R I N G"\r line 0 600 decimal 3 "Module status read interval (in 100 ms)"\r eline " "\r line 0 65500 decimal 5 "Module hardware monitoring frequency"\r line 0 65500 decimal 5 "Module status log frequency"\r eline " "\r line 0 65500 decimal 5 "ECC monitoring frequency"\r line 0 65500 decimal 5 "ECC limit"\r line 0 65500 decimal 5 "ECC log frequency"\r fmenu FMN_SLOTNO 0 216 " "\r line 0 15 decimal 2 "Slot number"\r fmenu FMN_FNAME 0 217 "L O A D C P U L O C A L M E M O R Y"\r line 0 0 string 16 "File name"\r fmenu FMN_UTST 0 3073 "E X E C U T E U N K N O W N L O C A L T E S T"\r line 4 7 testtypes 8 "Test type"\r line 0 63 decimal 2 "Test number"\r line 1 2 yesno 3 "Loop in test"\r line 4 6 erract 8 "Error handling"\r line 1 2 yesno 3 "Log informative messages"\r line 1 2 yesno 3 "Store informative messages"\r fmenu FMN_CHPAR 0 3072 "C H A N G E T E S T P A R A M E T E R S"\r line 1 2 yesno 3 "Loop in test"\r line 4 6 erract 8 "Error handling"\r line 1 2 yesno 3 "Log informative messages"\r line 1 2 yesno 3 "Store informative messages"\r fmenu FMN_STST 0 2304 "P A R A M E T E R S F O R S E P A R A T E L O C A L T E S T"\r line 1 16 decimal 2 "Number of parameter words"\r line 0 65535 hex 4 "Parameter word 0 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 1 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 2 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 3 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 4 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 5 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 6 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 7 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 8 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 9 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 10 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 11 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 12 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 13 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 14 (in hexadecimal)"\r line 0 65535 hex 4 "Parameter word 15 (in hexadecimal)"\r fmenu FMN_FNAMECNTL 0 221 "L O A D C O N T R O L L E R P R O G R A M"\r line 0 0 string 16 "File name"\r line 1 2 yesno 3 "Include debugger"\r line 1 2 yesno 3 "Go"\r fmenu FMN_SIG 0 222 "S E T I G N O R E F O R S P E C I A L T E S T S"\r line 1 2 yesno 3 "Ignore no memory error"\r line 1 2 yesno 3 "Ignore no CPU error"\r line 1 2 yesno 3 "Ignore no IOC error"\r line 1 2 yesno 3 "Ignore no DLC/DLU error"\r eline " "\r line 1 2 yesno 3 "Ignore system bus timeouts"\r line 1 2 yesno 3 "Ignore system bus conditions"\r line 1 2 yesno 3 "Ignore system bus errors"\r eline " "\r line 1 2 yesno 3 "Ignore module errors"\r eline " "\r line 1 2 yesno 3 "Start RC CPU"\r line 1 2 yesno 3 "Start RC timer"\r fmenu FMN_ILOG 0 223 "I N I T I A L L O G S E T T I N G S"\r line 1 2 yesno 3 "Log on printer after power-up"\r line 1 2 yesno 3 "Log on diskette after power-up"\r line 1 4 loglevel 11 "Diskette severity level"\r line 1 4 loglevel 11 "Display severity level"\r fmenu FMN_CNTL_1 0 2305 "C O N T R O L L E R M E M O R Y T E S T"\r line 0 65535 dhex 8 "Start address (hexadecimal)"\r line 0 65279 dhex 4 " "\r eline " "\r line 0 65535 dhex 8 "Block size in bytes (hexadecimal)"\r line 0 65535 dhex 4 " "\r eline " "\r line 2 7 decimal 1 "System bus format (2-7)"\r eline " "\r line 0 65535 hex 4 "Test pattern (0:counting)"\r fmenu FMN_DLC901_1 0 2306 "DLC DMA GLOBAL MEMORY ACCESS TEST 2"\r line 0 65535 dhex 8 "Start address (hexadecimal)"\r line 0 65279 dhex 4 " "\r eline " "\r line 0 65535 hex 4 "Block size in 16-bit word (hexadecimal)"\r eline " "\r line 1 2 decimal 3 "Source buffer number (decimal)"\r line 0 65535 hex 4 "Source buffer offset (hexadecimal)"\r eline " "\r line 1 2 decimal 3 "Destination buffer number (decimal)"\r line 0 65535 hex 4 "Destination buffer offset (hexadecimal)"\r eline " "\r line 0 65535 hex 4 "Test pattern (hexadecimal)"\r line 1 7 decimal 3 "Transfer format (decimal)"\r fmenu FMN_DLC901_2 0 2307 "D L C S E P A R A T E L A N T E S T S"\r line 1 2 decimal 1 "LAN controller number"\r fmenu FMN_CPU901_1 0 2308 "R I S C C P U G L O B A L M E M O R Y T E S T"\r line 0 65531 dhex 8 "Start address (hexadecimal)"\r line 8 65279 dhex 4 " "\r eline " "\r line 0 65535 dhex 8 "Block size in bytes (hexadecimal)"\r line 0 65535 dhex 4 " "\r eline " "\r line 0 2 decimal 1 "System bus format (0-2)"\r fmenu FMN_CPU985_1 0 2309 "R C C P U G L O B A L M E M O R Y T E S T"\r line 0 65534 dhex 6 "Start address (halfword - hexadecimal)"\r line 4 255 dhex 4 " "\r eline " "\r line 0 65535 dhex 6 "Block size in halfwords (hexadecimal)"\r line 0 65535 dhex 4 " "\r fmenu FMN_CPU901_2 0 2310 "R I S C C P U G L O B A L M E M O R Y W A I T T E S T"\r line 0 0 dhex 8 "Word address (hexadecimal)"\r line 0 128 dhex 4 " "\r eline " "\r line 0 0 dhex 8 "Byte address (hexadecimal)"\r line 0 128 dhex 4 " "\r dmenu DMN_MSTAT 61 "D I S P L A Y M O D U L E S T A T U S"\r line 1 3 pstates modules decimal \r "PU state=%s. Main processor=%s. %d Mb global memory" \r line 1 0 \r "Slot Mod.id. State Cust.id. Serial no. FCO Level Soft.Version"\r line 16 8 decimal modules decimal mstates modules string string string\r " %2d %7s%c %13s %7s %10s %10s %17s"\r dmenu DMN_TST 224 "D I S P L A Y T E S T M E S S A G E S"\r line 1 2 decimal modules "Listing messages for slot %d (%s)"\r line 16 1 string "%s"\r dmenu DMN_ATST 226 "D I S P L A Y A L L T E S T M E S S A G E S"\r line 17 1 string "%s"\r dmenu DMN_LOG 228 "D I S P L A Y S S P L O G"\r line 1 3 procs logno loglevel "Listing messages for %s from %s log. Severity = %s"\r line 16 1 string "%s"\r fmenu FMN_SET_SPCCONF 0 229 "S E T S P E C I A L C U S T O M I Z A T I O N V A L U E S"\r line 0 3 decimal 1 "IOSERVER identification"\r line 0 3 decimal 1 "RPU identification"\r line 0 1440 decimal 4 "Minimum OS uptime before automatic reload (minutes)"\r line 1 65 decimal 2 "Waiting time before automatic reload (seconds)"\r line 1 65 decimal 2 "Time allowed for OS close down (seconds)"\r line 8 512 decimal 3 "Memory (in Mbytes) allocated for TX and users"\r line 1 3 yesno 5 "Fast system bus"\r line 1 2 refill 7 "Instruction cache refill size during test"\r line 1 2 refill 7 "Instruction cache refill size for RPU"\r line 1 2 refill 7 "Instruction cache refill size for UPU"\r fmenu FMN_SET_SSPCPL 0 230 "S E T S S P C O U P L I N G S"\r line 0 255 decimal 3 "Number of couplings to RPU"\r line 0 255 decimal 3 "Number of couplings to UPU"\r line 0 255 decimal 3 "Number of couplings to IOSERVER"\r line 0 255 decimal 3 "Number of couplings to CPU8500"\r eline " "\r line 0 255 decimal 3 "Number of couplings to IOC"\r line 0 255 decimal 3 "Number of couplings to SIB"\r line 0 255 decimal 3 "Number of couplings to LAN"\r line 0 255 decimal 3 "Number of couplings to SLAVE SSP"\r fmenu FMN_SET_901CPL 0 231 "S E T R P U / U P U C O U P L I N G S"\r line 0 255 decimal 3 "Number of couplings between RPU and UPU"\r eline " "\r line 0 255 decimal 3 "Number of couplings between RPU and IOC"\r line 0 255 decimal 3 "Number of couplings between RPU and SIB"\r line 0 255 decimal 3 "Number of couplings between RPU and LAN"\r line 0 255 decimal 3 "Number of couplings between RPU and SLAVE SSP"\r eline " "\r line 0 255 decimal 3 "Number of couplings between UPU and IOC"\r line 0 255 decimal 3 "Number of couplings between UPU and SIB"\r line 0 255 decimal 3 "Number of couplings between UPU and LAN"\r line 0 255 decimal 3 "Number of couplings between UPU and SLAVE SSP"\r fmenu FMN_SET_985CPL 0 232 "S E T I O S E R V E R / C P U 8 5 0 0 C O U P L I N G S"\r eline " "\r line 0 255 decimal 3 "Number of couplings between IOSERVER and CPU8500"\r eline " "\r line 0 255 decimal 3 "Number of couplings between IOSERVER and IOC"\r line 0 255 decimal 3 "Number of couplings between IOSERVER and LAN"\r line 0 255 decimal 3 "Number of couplings between IOSERVER and SLAVE SSP"\r eline " "\r line 0 255 decimal 3 "Number of couplings between CPU8500 and IOC"\r line 0 255 decimal 3 "Number of couplings between CPU8500 and LAN"\r line 0 255 decimal 3 "Number of couplings between CPU8500 and SLAVE SSP"\r fmenu FMN_AMODMON 0 233 "M O D U L E M O N I T O R I N G F O R A L L M O D U L E S"\r line 0 600 decimal 3 "Module status read interval (in 100 ms)"\r eline " "\r line 0 65500 decimal 5 "Module hardware monitoring frequency"\r line 0 65500 decimal 5 "Module watchdog monitoring frequency"\r line 0 65500 decimal 5 "Module status log frequency"\r eline " "\r line 0 65500 decimal 5 "ECC monitoring frequency"\r line 0 65500 decimal 5 "ECC limit"\r line 0 65500 decimal 5 "ECC log frequency"\r fmenu FMN_FNAMEMICR 0 234 "L O A D M I C R O P R O G R A M S"\r line 0 0 string 16 "RC CPU micro program file name"\r line 0 0 string 16 "RC FPU micro program file name"\r fmenu FMN_BRATE 0 235 "M O D E M C U S T O M I Z A T I O N"\r line 1 7 baudrate 5 "Modem baud rate"\r fmenu FMN_FNAMEMEM 0 236 "L O A D G L O B A L M E M O R Y P R O G R A M S"\r line 0 0 string 16 "First file name"\r line 0 0 string 16 "Second file name"\r fmenu FMN_SNOOP 0 237 "S T A R T S N O O P O N S Y S T E M B U S"\r line 0 15 decimal 2 "Slot number"\r line 1 2 yesno 3 "First data cycle"\r line 0 999 decimal 3 "Repeat count"\r fmenu FMN_SETRCX 0 238 "EXTRA MODEL 10 BASIS SYSTEM PARAMETERS"\r line 0 65000 decimal 5 "Unused 1"\r line 0 65000 decimal 5 "Unused 2"\r line 0 65000 decimal 5 "Unused 3"\r fmenu FMN_SETMPSIOC 0 239 "M O D E L T X I O C C U S T O M I Z A T I O N"\r line 0 15 decimal 2 "IOC no. 0 slot number"\r line 0 15 decimal 2 "IOC no. 1 slot number"\r line 0 15 decimal 2 "IOC no. 2 slot number"\r line 0 15 decimal 2 "IOC no. 3 slot number"\r fmenu FMN_CPU985_2 0 2311 "R C C P U D A T A C A C H E T E S T"\r line 0 65534 dhex 6 "Start address (halfword - hexadecimal)"\r line 4 255 dhex 4 " "\r eline " "\r line 0 65535 dhex 6 "Block size in halfwords (hexadecimal)"\r line 0 65535 dhex 4 " "\r eline " "\r line 0 8190 hex 4 "Cache offset in halfwords (hexadecimal)"\r fmenu FMN_SERNO 0 240 " "\r line 1 65534 decimal 5 "Serial number"\r fmenu FMN_REMEM 0 241 " "\r line 0 0 dhex 8 "Base address (in bytes)"\r line 0 65152 dhex 1 " "\r line 1 2 memtype 7 "Memory type (MEM8500 or MEM9000)"\r fmenu FMN_SETMPSLAN 0 242 "M O D E L T X L A N P A R A M E T E R S"\r line 0 0 string 8 "IMC node name"\r line 0 0 hstring 12 "Ethernet address"\r line 0 0 hstring 12 "IMC multicast address (IMCNETID)"\r line 1 255 decimal 3 "IMC region number"\r line 100 230 decimal 3 "LAN links (number of other stations)"\r line 120 1000 decimal 4 "IMC port name table size (IMCNAMES)"\r line 1 2730 decimal 4 "IMC relay table size (IMCRELAY)"\r line 0 20 decimal 2 "Number of TCP/IP send buffers"\r eline " "\r line 1 2 decimal 1 "Hardware LAN port used"\r fmenu FMN_SETLFNAME1 0 243 "SET LOAD FILE NAMES FOR MODEL 10 TEST PROGRAMS"\r line 0 0 string 16 "Test program for IPI IOC"\r line 0 0 string 16 "Test program for SCSI IOC"\r line 0 0 string 16 "Test program for DLC"\r line 0 0 string 16 "Test program for slave SSP"\r line 0 0 string 16 "Microprogram for RC CPU"\r line 0 0 string 16 "Microprogram for RC FPU"\r line 0 0 string 16 "First memory based test program for RC CPU"\r line 0 0 string 16 "Second memory based test program for RC CPU"\r fmenu FMN_GMEM_PAR 0 3074 "S S P B A S E D G L O B A L M E M O R Y T E S T"\r line 0 65535 dhex 8 "Start address (hexadecimal)"\r line 0 65279 dhex 4 " "\r line 0 65535 dhex 8 "Block size in bytes (hexadecimal)"\r line 0 65535 dhex 4 " "\r line 2 7 decimal 1 "System bus format (2-7)"\r line 0 65535 hex 4 "Test pattern (0=counting)"\r fmenu FMN_GCMEM_PAR 0 3075 "C P U B A S E D G L O B A L M E M O R Y T E S T"\r line 0 15 decimal 2 "CPU slotnumber"\r line 0 65531 dhex 8 "Start address (hexadecimal)"\r line 8 65279 dhex 4 " "\r line 512 65535 dhex 8 "Block size in bytes (hexadecimal)"\r line 0 65535 dhex 4 " "\r fmenu FMN_DG8MEM_PAR 0 244 "D U M P G L O B A L M E M O R Y O N D I S K E T T E"\r line 0 16383 decimal 8 "Start address of first dump in KHW (decimal)"\r line 0 790 decimal 8 "Size of first dump in KHW (decimal)"\r eline " "\r line 0 16383 decimal 8 "Start address of second dump in KHW (decimal)"\r line 0 790 decimal 8 "Size of second dump in KHW (decimal)"\r fmenu FMN_DCMEM_PAR 0 245 "D U M P C O N T R O L L E R M E M O R Y O N D I S K E T T E"\r line 1 15 decimal 2 "Controller slotnumber"\r line 0 9216 decimal 4 "Start address of dump in KB (decimal)"\r line 0 1024 decimal 4 "Size of dump in KB (decimal)"\r fmenu FMN_IOC901_1 0 2312 "I P I L O A D T E S T"\r line 0 65535 dhex 8 "Start address (hexadecimal)"\r line 0 65279 dhex 4 " "\r line 3 65535 hex 4 "Number of 16 bit words in the total data transfer (hexadecimal)"\r line 3 65535 hex 4 "Number of 16 bit words in each DMA transport (hexadecimal) " \r line 1 2 yesno 3 "Data check"\r eline " "\r line 1 2 yesno 3 "IPI slave 0 included in test"\r line 1 2 yesno 3 "IPI slave 1 included in test"\r line 1 2 yesno 3 "IPI slave 2 included in test"\r line 1 2 yesno 3 "IPI slave 3 included in test"\r line 1 2 yesno 3 "IPI slave 4 included in test"\r line 1 2 yesno 3 "IPI slave 5 included in test"\r line 1 2 yesno 3 "IPI slave 6 included in test"\r line 1 2 yesno 3 "IPI slave 7 included in test"\r fmenu FMN_IOC901_2 0 2313 "I P I C O M M U N I C A T I O N T E S T"\r line 1 2 yesno 3 "IPI slave 0 included in test"\r line 1 2 yesno 3 "IPI slave 1 included in test"\r line 1 2 yesno 3 "IPI slave 2 included in test"\r line 1 2 yesno 3 "IPI slave 3 included in test"\r line 1 2 yesno 3 "IPI slave 4 included in test"\r line 1 2 yesno 3 "IPI slave 5 included in test"\r line 1 2 yesno 3 "IPI slave 6 included in test"\r line 1 2 yesno 3 "IPI slave 7 included in test"\r fmenu FMN_SET_RCIMC 0 246 "M O D E L 1 0 L A N I M C P A R A M E T E R S"\r line 0 50 decimal 2 "Number of port handlers"\r line 1 100 decimal 3 "Max. number of connections per port"\r line 1 200 decimal 3 "Number of extra operations"\r line 1 10 decimal 2 "Number of port handler send buffers"\r line 2064 32000 decimal 5 "Size of port handler send buffers"\r line 0 0 hstring 12 "Ethernet address"\r line 0 0 hstring 12 "IMC multicast address (IMCNETID)"\r line 1 255 decimal 3 "IMC region number"\r line 100 230 decimal 3 "LAN links (number of other stations)"\r line 120 1000 decimal 4 "IMC port name table size (IMCNAMES)"\r line 200 1000 decimal 4 "IMC relay table size (IMCRELAY)"\r fmenu FMN_SETLFNAME2 0 247 "SET LOAD FILE NAMES FOR MODEL TX TEST PROGRAMS"\r line 0 0 string 16 "Test program for IPI IOC"\r line 0 0 string 16 "Test program for SCSI IOC"\r line 0 0 string 16 "Test program for DLC"\r line 0 0 string 16 "Test program for slave SSP"\r line 0 0 string 16 "Local test program for RISC CPU"\r line 0 0 string 16 "First memory based test program for RISC CPU"\r line 0 0 string 16 "Second memory based test program for RISC CPU"\r fmenu FMN_SETLFNAME3 0 248 "SET LOAD FILE NAMES FOR MODEL 10 OPERATING PROGRAMS"\r line 0 0 string 16 "Operating program for IPI IOC"\r line 0 0 string 16 "Operating program for DLC"\r line 0 0 string 16 "Operating program for slave SSP"\r line 0 0 string 16 "Microprogram for RC CPU"\r line 0 0 string 16 "Microprogram for RC FPU"\r line 0 0 string 16 "Operating program for RC CPU (MONITOR)"\r line 0 0 string 16 "Second operating program for RC CPU"\r fmenu FMN_SETLFNAME4 0 249 "SET LOAD FILE NAMES FOR MODEL TX OPERATING PROGRAMS"\r line 0 0 string 16 "Operating program for IPI IOC"\r line 0 0 string 16 "Operating program for SCSI IOC"\r line 0 0 string 16 "Operating program for DLC (LAN)"\r line 0 0 string 16 "Operating program for DLC (SIB)"\r line 0 0 string 16 "Operating program for slave SSP"\r line 0 0 string 16 "Operating program for local memory on RISC CPU (RPU)"\r line 0 0 string 16 "Operating program for local memory on RISC CPU (UPU)"\r line 0 0 string 16 "Operating program for RISC CPU (Debugger)"\r line 0 0 string 16 "Operating program for RISC CPU (RTE)"\r fmenu FMN_SETMPSCLAN 0 250 "M O D E L T X L A N / S I B C U S T O M I Z A T I O N"\r line 0 15 decimal 2 "LAN DLC no. 0 slot number"\r line 0 65000 string 6 "LAN no. 0 name"\r line 0 15 decimal 2 "LAN DLC no. 1 slot number"\r line 0 65000 string 6 "LAN no. 1 name"\r line 0 15 decimal 2 "LAN DLC no. 2 slot number"\r line 0 65000 string 6 "LAN no. 2 name"\r line 0 15 decimal 2 "LAN DLC no. 3 slot number"\r line 0 65000 string 6 "LAN no. 3 name"\r eline " "\r line 0 15 decimal 2 "First SIB DLC/DLU slot number"\r line 0 65000 string 6 "SIB no. 0 name"\r line 0 65000 string 6 "SIB no. 1 name"\r line 0 15 decimal 2 "Second SIB DLC/DLU slot number"\r line 0 65000 string 6 "SIB no. 2 name"\r line 0 65000 string 6 "SIB no. 3 name"\r fmenu FMN_SETCUST30 0 251 "M O D E L T X C A P A B I L I T Y P A R A M E T E R S"\r line 5 50 decimal 2 "Percent memory used for disk cache"\r line 16 512 decimal 3 "Number of pseudo terminals"\r line 90 400 decimal 3 "Number of text segments"\r line 400 1500 decimal 4 "Number of processes"\r line 400 5000 decimal 4 "Number of inodes"\r line 500 5000 decimal 4 "Number of open files"\r line 400 1500 decimal 4 "Number of callouts"\r line 64 256 decimal 3 "Number of opens to MXIPC files"\r line 60 500 decimal 3 "Reopen timeout value (in seconds)"\r line 30 500 decimal 3 "Number of processes per user"\r line 8 512 decimal 3 "Number of shared memory segments"\r line 4 16 decimal 2 "Number of attached shared memory segments per process"\r fmenu FMN_SETCUST30X 0 252 "I / O S E R V E R P A R A M E T E R S"\r line 1 8 decimal 1 "Number of I/O servers"\r line 1 8 decimal 1 "Number of allocation servers"\r line 1 8 decimal 1 "Number of fast I/O servers"\r line 1 8 decimal 1 "Number of read without inode lock servers"\r line 1 8 decimal 1 "Number of fsquid servers"\r line 1 8 decimal 1 "Number of nameservers"\r line 176 1024 decimal 4 "RTE heap size in pages (4 kbytes)"\r line 1500 4576 decimal 5 "Maximum size of SIB frame in bytes"\r fmenu FMN_SETMPSC_SCSI 0 253 "M O D E L T X S C S I C U S T O M I Z A T I O N"\r line 1 7 decimal 1 "Own initiator target no."\r line 0 0 decimal 1 "Own test target no. (fixed)"\r eline " "\r line 1 9 decimal 1 "Other initiator target no."\r line 0 0 decimal 1 "Other test target no. (fixed)"\r fmenu FMN_IOC911_1 0 2314 "S C S I T A P E T E S T"\r line 1 2 yesno 3 "Reset SCSI bus before execution"\r line 0 7 decimal 1 "SCSI initiator no."\r line 0 7 decimal 1 "SCSI target no."\r line 66 77 bufmed 6 "Test drive Buffer or Medium"\r line 65 67 countalt 5 "Test pattern, counting or alternating (5555 AAAA)"\r line 0 252 decimal 3 "Number of blocks per command"\r line 0 65535 decimal 5 "Number of blocks (x 1024) to test (base)"\r line 0 1023 decimal 4 "Number of blocks to test (offset)"\r line 1 2 yesno 3 "Write to drive"\r line 1 2 yesno 3 "Read from drive"\r line 1 2 yesno 3 "Data check"\r line 0 65535 dhex 8 "Global memory address (hexadecimal)"\r line 0 65279 dhex 4 " "\r line 1 2 yesno 1 "Retension before operation"\r fmenu FMN_IOC911_2 0 2315 "S C S I D I S K T E S T"\r line 1 2 yesno 3 "Reset SCSI bus before execution"\r line 0 7 decimal 1 "SCSI initiator no."\r line 0 7 decimal 1 "SCSI target no."\r line 66 77 bufmed 6 "Test drive Buffer or Medium"\r line 65 67 countalt 5 "Test pattern, counting or alternating (5555 AAAA)"\r line 0 252 decimal 3 "Number of blocks per command"\r line 0 65535 decimal 5 "Number of blocks (x 1024) to test (base)"\r line 0 1023 decimal 4 "Number of blocks to test (offset)"\r line 1 2 yesno 3 "Write to drive"\r line 1 2 yesno 3 "Read from drive"\r line 1 2 yesno 3 "Data check"\r line 0 65535 dhex 8 "Global memory address (hexadecimal)"\r line 0 65279 dhex 4 " "\r line 0 65535 decimal 5 "Start test at block address x 1024 (base)" \r line 0 1023 decimal 4 "Start test at block address (offset)"\r line 65 83 seqalt 3 "Access mode, Sequential or Alternate"\r fmenu FMN_IOC911_3 0 2316 "S C S I F O R M A T T E S T"\r line 1 2 yesno 3 "Reset SCSI bus before execution"\r line 0 7 decimal 1 "SCSI initiator no."\r line 0 7 decimal 1 "SCSI target no."\r line 256 4096 decimal 4 "Logical block (sector) size"\r fmenu FMN_RCMEM 0 254 "M E M O R Y U S A G E"\r line 1024 8192 decimal 4 "Memory (kilo halfwords) allocated for Monitor and users"\r fmenu FMN_DLU901_1 0 2317 "D L U C O N C U R R E N T C H A N N E L T E S T"\r line 0 65535 dhex 8 "Test start address (hex)"\r line 0 65279 dhex 4 " "\r line 384 65535 dhex 8 "Test block size (hex)"\r line 0 65279 dhex 4 " "\r eline "Subtest 1:"\r line 32 65535 hex 4 "Frame size (hex)"\r line 32 32768 hex 4 "Subframe size (hex)"\r line 0 255 hex 2 "Test pattern (hex)"\r line 1 2 yesno 3 "Data Check"\r line 1 3 chan 8 "Transmit channel"\r line 1 3 chan 8 "Receive channel"\r eline "Subtest 2:"\r line 32 65535 hex 4 "Frame size (hex)"\r line 32 32768 hex 4 "Subframe size (hex)"\r line 0 255 hex 2 "Test pattern (hex)"\r line 1 2 yesno 3 "Data Check"\r line 1 3 chan 8 "Transmit channel"\r line 1 3 chan 8 "Receive channel"\r fmenu FMN_CHSSPPAR 0 3076 "C H A N G E S S P T E S T P A R A M E T E R S"\r line 1 2 yesno 3 "Loop in test"\r line 4 6 erract 8 "Error handling"\r line 1 2 yesno 3 "Log informative messages"\r line 1 2 yesno 3 "Store informative messages"\r error MMSG_ILL_SEL "*** Illegal selection ***"\r error MMSG_ILL_CHAR "*** Illegal character ***"\r error MMSG_ILL_VAL "*** Illegal value ***"\r info MMSG_COPYRIGHT "Copyright ICL DATA A/S %s Version: %s (%s)"\r error MMSG_UNKNOWN "*** Function %d not implemented ***"\r info MMSG_TIME_SET "Date and time set"\r info MMSG_ZONE_SET "Timezone set"\r error MMSG_RTCACC "Unable to access real time clock"\r info MMSG_MODID_SET "Module customization set to actual configuration"\r error MMSG_ILL_DATE "*** Illegal date ***"\r info MMSG_RC_SET "Model 10 parameters set"\r error MMSG_ILL_RC "*** Illegal model 10 parameters ***"\r error MMSG_ILL_RCNAME "*** Illegal process name ***"\r info MMSG_MPS_SET "Model 30/40 parameters set"\r error MMSG_ILL_MPS "*** Illegal model 30/40 parameters ***"\r info MMSG_CONFREAD "Customization data read"\r info MMSG_CONFWRITTEN "Customization data written"\r error MMSG_NO_TL "*** No test and load utilities in %s state ***"\r error MMSG_ILL_STATE "*** Operation not legal in %s state ***"\r info MMSG_CLOG "Current log mode is %s"\r info MMSG_CSTATE "Current state is %s"\r error MMSG_OSTATE "*** WARNING: Operating system is running ***"\r error MMSG_ILLSET "*** Date/time must be set in operating system ***"\r error MMSG_NOMODMON "*** No module monitoring for %s (Slot %d) ***"\r info MMSG_MODMON "Module monitoring for %s (Slot %d)"\r error MMSG_CNFOLD "*** Customization data on diskette may be obsolete ***"\r error MMSG_DKCERR "*** Unable to close files on diskette ***"\r info MMSG_RMDK "*** Remove diskette and insert new diskette ***"\r info MMSG_CTSTMSG "All test messages cleared"\r error MMSG_NOSSPTST "*** No SSP based tests for %s (Slot %d) ***"\r error MMSG_NO_CUST "*** No customization for %s (Slot %d) ***"\r info MMSG_SSPTST "Execute SSP based tests for %s (Slot %d)"\r error MMSG_NOMODTST "*** No module tests for %s (Slot %d) ***"\r info MMSG_MODTST "Execute module tests for %s (Slot %d)"\r info MMSG_TSTLOAD "Load test program for %s (Slot %d)"\r info MMSG_TSTGLOAD "Load test program into global memory"\r info MMSG_SMODTST "Separate test %d for %s (Slot %d)"\r info MMSG_S_PUTA "Command sent to PU test administrator"\r info MMSG_LDLOAD "Load operating program for %s (Slot %d)"\r info MMSG_LDGLOAD "Load operating program into global memory"\r error MMSG_NOMODLD "*** Cannot load program into %s (Slot %d) ***"\r info MMSG_S_PULA "Command sent to PU load administrator"\r error MMSG_ILL_FNAME "*** Illegal file name ***"\r info MMSG_WEEK "Current weekday is %s"\r error MMSG_UNAPWU "Unable to power up"\r info MMSG_PI4DEB "Debugning of PI 4 kernel on module %s (Slot %d)"\r info MMSG_PI4_NMI "NMI sent to module %s (Slot %d)"\r info MMSG_PI4_ERR "PI4 error %04XH on module %s (Slot %d)"\r info MMSG_PI4_GO "PI4 kernel restarted on module %s (Slot %d)"\r info MMSG_LANCNTL "Parameters for LAN controller %d"\r info MMSG_SCSICNTL "Parameters for SCSI controller (Slot %d)"\r info MMSG_REMEM "Re-configuring %s (slot %d)"\r error MMSG_NO_MEMMOD "Slot %d does not contain a memory module"\r info MMSG_CONFREADING "Reading customization data - please wait"\r info MMSG_CONFWRITING "Writing customization data - please wait"\r error MMSG_EXTP_BIG "Device number must be less than or equal %d"\r error MMSG_SLOT_TWICE "Slot %d used more than once"\r error MMSG_EXTP_TWICE "Device number %d used more than once"\r error MMSG_TARG_TWICE "Target number %d used more than once"\r error MMSG_TARG_BIG "Target number %d too big"\r info MMSG_DG8MEM "Dumping %d KHW from hw-address %06xh into file %s"\r info MMSG_DCMEM "Dumping %d KB from %s(slot %d) address %06xh into file %s"\r info MMSG_DFINI "Dump successfully finished" \r error MMSG_DERR "IO-error %d during dump (file=%s)"\r error MMSG_DSTART "Dump on diskette started"\r info MMSG_PUSET "PU name set"\r info MMSG_CNFSET "Module configuration set"\r info MMSG_DSENT "Dump command sent to IOC's"\r error MMSG_RCLANERR1 "Total number of terminal handlers and consoles must not exceed %d."\r info MMSG_RCLANOK "Lan %d. %d out of %d bytes used. %d out of %d buffers used."\r error MMSG_RCLANNOMEM "Lan %d. %d bytes memory used only %d available. (%d,%d)."\r error MMSG_RCLANNOBUF "Lan %d. %d buffer used only %d available. (%d,%d)."\r info MMSG_POWER "Voltage error on %s. Power supplies %s active"\r info MMSG_MONSIZ "Maximum size of monitor tables is %d words"\r error MMSG_MONBIG "Monitor tables too big : %d word - allowed %d words"\r error MMSG_ILLSET8 "*** Date/time must be set when operating system is not active ***"\r error MMSG_EXTP_ILL "Device number 20-35 are reserved for main processes"\r error MMSG_CUST_RERR "*** Error when reading customization data"\r error MMSG_CUST_WERR "*** Error when writing customization data"\r error MMSG_NO_CNTLMOD "Slot %d does not contain a controller"\r error MMSG_CMDSENT "Command sent to slot %d (%s)"\r error MMSG_NO_SERV_EXC "Number of servers (%d) may not exceed %d"\r