DataMuseum.dk

Presents historical artifacts from the history of:

Regnecentalen RC-900

This is an automatic "excavation" of a thematic subset of
artifacts from Datamuseum.dk's BitArchive.

See our Wiki for more about Regnecentalen RC-900

Excavated with: AutoArchaeologist - Free & Open Source Software. 

top - metrics - download

⟦6f676ef61⟧ TextFile

    Length: 8460 (0x210c)
    Types: TextFile
    Notes: UNIX file
    Names: »Pcap«

Derivation

└─⟦c93a30372⟧ Bits:30004169/disk3.imd Uniplex II+ V.6 release 1.0 (dansk)
└─⟦c93a30372⟧ UNIX Filesystem
    └─⟦this⟧ »up/new/usr/UAP/unsupported/Pcap«

TextFile


*********************************************************************
*
* PRINTER SECTIONS for those printers which have not been setup for
* proportional spacing printing, and use settings formerly used by 
* UPRINT only. 
* NB: If you have created a printer entry in Tcap for use with uprint
* and you want to use this with uprop; The entry must be copied into 
* Pcap and either the VMI work done or simply add the following to the
* entry:- FONTINIT='D-NORMAL',0,0
*
* To improve printer capabilities refer to config manual and insert 
* values for VMIBEG, VMIPIN, VMIMAX, VMIOFST etc... for the required 
* printers.
*
* To enable a printer to use proportional spacing one must enter the
* correct values for HMIBEG, HMIPIN etc... , as explained in the config
* manual.
*
* If a printer can use different fonts then amendments must be made to
* Fcap as detailed by the configuration manual.
*
* Standard Printer .SN strings:
*
* PNAME= Printer name, and CR
* CX  = Right hand margin bars:
* CN    "Change Next" - next line only
* C2    "Change two"  - next 2 lines
* CS    "Change start" - start of series of bars (or start marker)
* CE    "Change end"   - end of series of bars (or end marker)
*
*********************************************************************

*********************************************************************
*
*       Default dump printer.   A good addition to the dumb
*       printer is 'FF=12' as most deficient printers can
*       support formfeed.
*
*********************************************************************

* Genicom stuff:
* CPIxx Set appropriate CPI and Gothic NLQ
* TINY  Set microfont

* Alternate INIT=$-'[s'-$-'[m'-$-'[13m'-$-'[;60 G'
* can be used to:
*       Set default page layout (from SETUP)
*       Set off any print enhancements (u/line, bold, etc)
*       Set Gothic NLQ
*       Set 12 CPI

#genicom
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: genicom'-13
INIT=$-'[s'-$-'[m'
A=$-'[1m',$-'[m'
B=$-'[1m',$-'[m'
C=$-'[4m',$-'[m'
D=$-'[4m',$-'[m'
E=$-'[1;4m',$-'[m'
FF=12
CPI10=$-'[13m'-$-'[;72 G'
CPI12=$-'[13m'-$-'[;60 G'
CPI17=$-'[13m'-$-'[;55 G'
TINY=$-'[14m'-$-'[;40 G'
))

.PA


*       diablo is a minimal set of the diablo 630 series

#diablo
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: diablo'-13
J=$-'U',$-'D'
K=$-'D',$-'U'
W=$-'A',$-'B'
))

*       diablo 630 with WP option

#diablo-wp
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: diablo-wp'-13
A=$-'O',$-'&'
B=$-'W',$-'&'
C=$-'E',$-'R'
J=$-'U',$-'D'
K=$-'D',$-'U'
W=$-'A',$-'B'
))
W = Red print (ribbon down)

*********************************************************************
*
*               QUME printers
*
*********************************************************************

#qume
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: epson'-13
A=$-'K',$-'M'
B=$-'Q',$-'R'
C=$-'I',$-'J'
J=$-'U',$-'D'
K=$-'D',$-'U'
W=$-'A',$-'B'
FF=12
))

.PA
******************************************************
* Quietwriter Printer
*
* NB Map Null character to 2 in the codes, then map it
*    back in MAP
*    PITCH is to proper Bolding on this printer
*
******************************************************

#quiet
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: quiet'-13
PITCH=$-'d'-1-2,8
C=$-'-'-1,$-'-'-2
E='AC',0
BOXC=196-179-197-218-194-191-180-217-193-192-195
BOXE='           '
FILLC=254-178-177-176-219-249-206-221-220-197
FILLE='          '
MAP=2,0
))

.PA
**********************************************
* IBM Proprinter XL driver for UNIPLEX-II Plus
**********************************************

#proxlletter
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: proxlletter'-13
INIT=$-71
DEINIT=$-72
A=$-69,$-70
C=$-45-1,$-45-2
E='AC',0
F=$-87-1,$-87-2
G='FA',0
H='FC',0
I='FAC',0
J=$-83-2,$-84
K=$-83-1,$-84
L=$-91-64-4-2-2-2-18-2,$-91-64-4-2-2-2-17-2
BOXC=196-179-197-218-194-191-180-217-193-192-195
BOXE='
FILLC=219-177-176-178-206-220-222-197-215-232
FILLE='
MAP=2,0
))

#proxldraft
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: proxldraft'-13
A=$-69,$-70
C=$-45-1,$-45-2
E='AC',0
F=$-87-1,$-87-2
G='FA',0
H='FC',0
I='FAC',0
J=$-83-2,$-84
K=$-83-1,$-84
L=$-91-64-4-2-2-2-18-2,$-91-64-4-2-2-2-17-2
BOXC=196-179-197-218-194-191-180-217-193-192-195
BOXE='
FILLC=219-177-176-178-206-220-222-197-215-232
FILLE='
MAP=2,0
))

************
* PROPRINTER
************

#proprinter
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: proprinter'-13
A=$-'E',$-'F'
B=$-'G',$-'H'
C=$-'-'-1,$-'-'-2
E='AC',0
BOXC=196-179-197-218-194-191-180-217-193-192-195
BOXE='           '
FILLC=219-177-176-178-206-220-222-197-215-232
FILLE='          '
MAP=2,0
))

.PA
*********************************************************************
*
*               UIS Printer Definitions
*
*********************************************************************
*********************************************************************
*
*               Toshiba printers
*
*       Toshiba.graph.lq is a full Toshiba listing:
*       For variations replace the appropriate INIT entries.
*       Do not use the entries directly
*
*********************************************************************
##toshiba               INIT=$-26-73
##toshiba.lq.10-6       INIT=27-26-73-27-42-49-27-69-49-50-27-76-48-56
##toshiba.lq.10-8       INIT=27-26-73-27-42-49-27-69-49-50-27-76-48-54
##toshiba.lq.12-6       INIT=27-26-73-27-42-49-27-69-49-48-27-76-48-56
##toshiba.lq.12-8       INIT=27-42-49-27-69-49-48-27-76-48-54
##toshiba.dq.12-6       INIT=27-26-73-27-69-49-50-27-76-48-56
##toshiba.man.10-6      INIT=27-26-73-27-42-49-27-69-49-50-27-76-48-56

#toshiba.graph.lq
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: toshiba.graph.lq'-13
INIT=27-26-73-27-42-49-27-69-49-50-27-76-48-56
DEINIT=27-26-73
C=27-73,27-74
E=27-42-50-27-73,27-42-49-27-74
F=27-33,27-34
G=27-42-50-27-33,27-42-49-27-34
H=27-33-27-73,27-34-27-74
I=27-42-50-27-33-27-73,27-42-49-27-34-27-74
J=27-85,27-68
K=27-68,27-85
M=27-42-49-27-34-27-74,27-42-49-27-34-27-74
N=27-'5'-27-61-27-68-245-27-85-8-27-85-245-27-68-8,27-63
O=27-'5'-27-61-27-85-245-27-68-8,27-63
P=27-'5'-27-61-27-68-245-27-85-8,27-63
[=27-'5'-27-61,27-63
BOXC=241-245-250-240-243-242-249-247-248-246-244
BOXE='[NNOOONPPPN'
FILLC=239-254-253-252-251-234-233-232-230-228
FILLE='[[[[[[[[[['
MAP='~',' '
MAP=31,'~'
MAP=10,10-13
))

.PA
*********************************************************************
*
*               Citizen printers
*
*********************************************************************

#citizen.dq.10-6.nml
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: citizen.dq.10-6.nml'-13
INIT=$-'[5i'
DEINIT=$-'[4i'
A=$-'E',$-'F'
B=$-'G',$-'H'
C=$-'-1',$-'-0'
E=$-'E'-$-'-1',$-'F'-$-'-0'
F=$-'W1',$-'W0'
G=$-'W1'-$-'E',$-'W0'-$-'F'
H=$-'W1'-$-'-1',$-'W0'-$-'-0'
I=$-'W1'-$-'E'-$-'-1',$-'W0'-$-'F'-$-'-0'
J=$-'S0',$-'T'
K=$-'S1',$-'T'
L=$-'4'-$-'E'-$-'G',$-'5'-$-'F'-$-'H'
M=$-'F'-$-'-0'-$-'W0'-$-'5',$-'F'-$-'-0'-$-'W0'-$-'5'
[=$-'x0'-$-'E'-$-'G'-$-'>'-$-'U1',$-'#'-$-'F'-$-'H'-$-'x1'
BOXC='D3EIK?4>ASF'
BOXE='[[[[[[[[[[['
FILLC='0[/E2p#/*+%'
FILLE='[[[[[[     '
))

#scitizen.dq.10-6.nml
FONTINIT='NORMAL',0,0
PNAME='Printer Tcap name: scitizen.dq.10-6.nml'-13
INIT=$-'@'
DEINIT=$-'@'
A=$-'E',$-'F'
B=$-'G',$-'H'
C=$-'-1',$-'-0'
E=$-'E'-$-'-1',$-'F'-$-'-0'
F=$-'W1',$-'W0'
G=$-'W1'-$-'E',$-'W0'-$-'F'
H=$-'W1'-$-'-1',$-'W0'-$-'-0'
I=$-'W1'-$-'E'-$-'-1',$-'W0'-$-'F'-$-'-0'
J=$-'S0',$-'T'
K=$-'S1',$-'T'
L=$-'4'-$-'E'-$-'G',$-'5'-$-'F'-$-'H'
M=$-'F'-$-'-0'-$-'W0'-$-'5',$-'F'-$-'-0'-$-'W0'-$-'5'
[=$-'x0'-$-'E'-$-'G'-$-'>'-$-'U1',$-'#'-$-'F'-$-'H'-$-'x1'
BOXC='D3EIK?4>ASF'
BOXE='[[[[[[[[[[['
FILLC='0[/E2p#/*+%'
FILLE='[[[[[[     '
))
.PA
#laser
RESTORE
PNAME='Printer Tcap name: laser'-13
DEINIT=$-'E'
FF=12
A=$-'(s7B',$-'(s0B'
B=$-'(s7B',$-'(s0B'
C=$-'&dD',$-'&d@'
D=$-'&dD',$-'&d@'
E='AC',0
G=$-'(s7B',$-'(s0B'
H=$-'(s7B',$-'(s0B'
I=$-'(s1S',$-'(s0S'
J=$-'(0B',$-'(0U',127
M=$-'&dD',$-'&d@','_'
T=$-'(0B',$-'(0U',127
[=$-'(0B',$-'(0U'
BOXC=',./r7t6g8f5'
BOXE='[[[[[[[[[[['
FILLC=127-'0c?dxz><)'
FILLE='[[[[[[[[[['
LINE='  ______________________________________________________________________'-13-10
ITALIC=$-'(s1S'
NORMAL=$-'&l0O'-$-'(0U'-$-'(s0p1oh12v0s0b3T'
LANDSCAPE=$-'&l1O'-$-'(8U'-$-'(s0p1oh12v0s0b3T'
PORTRAIT=$-'&l0O'
CN=$-'&a+99C'-8-$-'(0B:'-13-$-'(0U'
C2=$-'&a+99C'-8-$-'(0B:'-8-$-'&a+1R:'-$-'&a-1R'-13-$-'(0U'
CS=$-'&a+99C'-8-$-'(0Bw'-8-$-'&a+1R:'-$-'&a-1R'-13-$-'(0U'
CE=$-'&a+99C'-8-$-'(0B'-$-'&a-2R:'-8-$-'&a+1Rs'-$-'&a+1R'-13-$-'(0U'
))
.PA
***************
* End of File *
***************