|
DataMuseum.dkPresents historical artifacts from the history of: IBM System/3 |
This is an automatic "excavation" of a thematic subset of
See our Wiki for more about IBM System/3 Excavated with: AutoArchaeologist - Free & Open Source Software. |
top - metrics - download
Length: 3556 (0xde4)
Types: s3xseg
Names: »P$SGPCH«
└─⟦d025fa538⟧ Bits:30009183 5702-sc1.V16.2
└─⟦cfce0a73a⟧
└─⟦this⟧ »P$SGPCH«
└─⟦34f897e8c⟧ Bits:30009186 5702-sc1.V16.scp
└─⟦e1bdf435f⟧
└─⟦this⟧ »P$SGPCH«
// LOAD $MAINT,R1 * * ******************** INSTRUCTIONS FOR SCP SYSTEM GENERATION ******************** * * CARD INPUT AND OUTPUT*** MFCU OR 1442 *** * *** THIS CONTROL DECK PUNCHES OUT THE SCP SYSTEM GENERATION INSTRUCTION CARDS *** AND PRINTS A LISTING OF THE PUNCHED CARDS ON THE PRINTER * *** THE FIRST CARD --A COPY CARD-- AND THE LAST CARD -- A CEND CARD-- THAT ARE *** PUNCHED OUT MUST BE DISCARDED. * *** SEPARATE THE DECK INTO TWO PARTS BY TAKING THE CARDS UP TO AND INCLUDING *** THE // RUN CARD THAT FOLLOWS THE // CALL $SGEN,R1 OFF THE FRONT OF THE *** DECK. PLACE THESE CARDS INTO THE PRIMARY HOPPER OF THE READER AND PRESS *** READER START. * *** THEN PRESS CONSOLE START --HALT/RESET IF YOU HAVE DPF SYSTEM-- * *** WHEN A HALT 90 IS DISPLAYED IN THE MESSAGE DISPLAY UNIT, THE SYSTEM *** CONFIGURATION STATEMENTS SHOULD BE MODIFIED AS REQUIRED TO REFLECT YOUR *** SYSTEM HARDWARE CONFIGURATION. *** BE SURE TO KEEP THESE CARDS IN THE SAME ORDER. WHEN CHANGES ARE COMPLETE, *** PLACE THE SYSTEM CONFIGURATION STATEMENTS IN THE PRIMARY HOPPER OF THE *** READER FOLLOWED BY THE REMAINING DECK OF PUNCHED CARDS AND PRESS READER *** START. * *** SET RIGHTMOST ADDRESS/DATA SWITCH TO 0, *** THEN PRESS CONSOLE START -HALT/RESET IF YOU HAVE DPF SYSTEM- TO CONTINUE * *** WHEN HALT 91 IS DISPLAYED IN THE MESSAGE DISPLAY UNIT,THE ALLOCATE *** STATEMENT FOR THE LIBRARIES SHOULD BE MODIFIED AS REQUIRED TO *** REFLECT YOUR SYSTEM LIBRARY REQUIRMENTS . BE SURE TO KEEP THE STATEMENTS *** IN ORDER . WHEN CHANGES ARE COMPLETE PLACE THE ALLOCATE STATEMENT *** IN THE PRIMARY HOPPER FOLLOWED BY THE REMAINING CONTROL STATEMENTS *** AND PRESS READER START. * *** SET RIGHTMOST ADDRESS/DATA SWITCH TO 0, *** THEN PRESS CONSOLE START --HALT/RESET IF YOU HAVE DPF SYSTEM-- TO CONTINUE * * *** WHEN A HALT 90 IS AGAIN DISPLAYED IN THE MESSAGE DISPLAY UNIT, *** SCP GENERATION IS COMPLETE. * *** END OF INSTRUCTIONS FOR SCP SYSTEM GENERATION USING CARD.*************** * ******************************************************************************* * * 3741 INPUT AND OUTPUT*** * *** THIS CONTROL PROGRAM OUTPUTS TO DISKETTE THE SCP GENERATION STATEMENTS *** AND PRINTS A LISTING OF THE STATEMENTS ON THE PRINTER. * *** SET THE 3741 OFF LINE AND POSITION AT THE OUTPUT(PUNCH) DATA SET IN THE *** UPDATE MODE. THE FIRST STATEMENT IS A --COPY STATEMENT-- DELETE IT. * *** NOW USE THE REC ADV KEY TO MOVE AHEAD TO EACH RECORD TO MODIFY THE *** CONFIGURATION STATEMENTS AS REQUIRED TO REFLECT YOUR SYSTEM HARDWARE *** CONFIGURATION. * *** THE ALLOCATION STATEMENT FOR THE LIBRARIES SHOULD BE MODIFIED NEXT *** TO REFLECT YOUR SYSTEM LIBRARY REQUIREMENTS. * *** NOW USE REC ADV KEY TO ADVANCE TO THE -CEND STATEMENT- DELETE THIS *** STATEMENT. * *** POSITION THE 3741 AT THE BEGINNING OF THE UPDATED PUNCH DATA SET AND *** PUT THE 3741 BACK ON LINE IN THE --READ MODE--. * *** RESPOND TO THE EJ HALT NOW TO CONTINUE. * *** END OF INSTRUCTIONS FOR SCP SYSTEM GENERATION USING 3741 ***************** * * * * READ THE INSTRUCTIONS GIVEN ABOVE. * * *** AFTER READING THE INSTRUCTIONS, SET RIGHTMOST ADDRESS/DATA SWITCH TO 0, *** PRESS CONSOLE START --HALT/RESET IF YOU HAVE DPF SYSTEM-- *** TO CONTINUE WITH SCP SYSTEM GENERATION. // PAUSE // RUN // COPY NAME-$SGPCH,LIBRARY-S,FROM-R1,TO-PRTPCH // END